PCM Connector for Inputs and Outputs 7139 Page of PCM Connector for Inputs and Outputs PCM Inputs and Outputs at PCM Connector A (50P) Terminal number Wire color Terminal name Description LT BLU FI MAIN RLY OUT Power source for PCM (POWER SOURCE) GRY DBW RLY OUT (IGNITION Detects ignition signal SIGNAL ETCS) WHT SHIFT LOCK SOL (SHIFT Drives shift lock solenoid 3*4 LOCK SOLENOID) PUR DBW RLY CL- Drives electronic throttle control system (ETCS) control relay (ELECTRONIC THROTTLE CONTROL SYSTEM (ETCS) CONTROL RELAY) Not used Not used *4 PUR IG1 MISS SOL (POWER Power source for solenoid valves SOURCE FOR SOLENOID VALVES) BLK GND (GROUND) Ground circuit for PCM WHT IG1 FUEL PUMP Detects ignition signal (IGNITION SIGNAL) PNK FI MAIN RLY CL- (PGM-FI Drives PGM-FI main relay 1 MAIN RELAY 1) 10 BLU +B IGP (VOLTAGE BACK Detects 12 volt battery voltage UP) 11 RED FUEL PUMP RLY CL- Drives PGM-FI main relay 2 (IMMOBILIZER FUEL PUMP RELAY) 12 Not used Not used 13 BRN FAN HI SIGNAL Drives A/C condenser fan relay, fan control relay (RADIATOR FAN CONTROL) 14 RED F-CAN_L (CAN Sends and receives communication signal COMMUNICATION SIGNAL LOW) 15 WHT F-CAN_H (CAN Sends and receives communication signal COMMUNICATION SIGNAL HIGH) 16 BLK GND (GROUND) Ground circuit for PCM *1: With keyless access system *2: CVT (with paddle shifter) *3: M/T *4: CVT *5: M/T (with keyless access system,17 model) https://biz.honda.co.jp/sip70/data/contents/sm/62T9AD90_2018_eng_EWD_20170630140 8/21/2017 PCM Connector for Inputs and Outputs 7139 Terminal number 17 Wire color Terminal name Page of Description BRN VCC4 (SENSOR Provides sensor reference voltage VOLTAGE) 18 LT GRN VCC5 (SENSOR Provides sensor reference voltage VOLTAGE) 19 Not used Not used 20 LT BLU TEVA (EVAPORATOR Detects evaporator sensor signal SENSOR) 21 Not used Not used *1 BLU ST CUT RLY2 CL- Drives starter cut relay 2 22 (STARTER RELAY 2) 23 GRN A/C MG CLUTCH RLY CL- Drives A/C compressor clutch relay (A/C COMPRESSOR CLUTCH RELAY) WHT ST CUT RLY1 CL- Drives starter cut relay 1 24*1 (STARTER RELAY 1) 25 RED CNG RLY CL- (CNG Drives CNG relay RELAY) 26 PUR FAN LO SIGNAL Drives radiator fan relay (RADIATOR FAN CONTROL) 27 BLU LIN (BATT SENSOR) Sends and receives communication signal (LOCAL INTERCONNECT NETWORK) 28 YEL S-NET (SERIAL Sends serial communication signal COMMUNICATION FOR IMMOBILIZER) 29 LT BLU SG4 (SENSOR GROUND) Sensor ground 30 BLU SG5 (SENSOR GROUND) Sensor ground 31 Not used Not used 32 WHT APS1 (ACCELERATOR Detects APP sensor A signal PEDAL POSITION (APP) SENSOR A) 33 Not used Not used 34 Not used Not used 35 BLU VSP (VEHICLE SPEED Sends vehicle speed signal SIGNAL OUTPUT) 36 Not used Not used 37 PNK SCS (SERVICE CHECK Detects service check signal SIGNAL) GRN STS (STARTER SWITCH Detects starter switch signal 38*1 SIGNAL) 39 LT GRN STOP LT (BRAKE PEDAL Detects brake pedal position switch signal POSITION SWITCH) *2 PNK PADDLE SW UP (PADDLE Detects paddle shifter ＋ (upshift switch) signal 40 SHIFTER ＋UPSHIFT SWITCH) 41 BLU PD SENSOR (A/C Detects A/C pressure sensor signal PRESSURE SENSOR) 42 PUR APS2 (ACCELERATOR Detects APP sensor B signal PEDAL POSITION (APP) SENSOR B) 43 Not used Not used *1 GRY START DIAG (STARTER Detects starter cut relay 44 RELAY RETURN SIGNAL) *1: With keyless access system *2: CVT (with paddle shifter) *3: M/T *4: CVT *5: M/T (with keyless access system,17 model) https://biz.honda.co.jp/sip70/data/contents/sm/62T9AD90_2018_eng_EWD_20170630140 8/21/2017 PCM Connector for Inputs and Outputs 7139 Terminal number 45 Wire color Terminal name PUR TEMP-P (TEMPERATURE CONTROL DIAL) LT GRN CLUTCH SW(SA) 46*5 (CLUTCH PEDAL POSITION SWITCH A SIGNAL) RED ATP-P (BYPASS FOR 47*4 TRANSMISSION RANGE SWITCH P POSITION SIGNAL) PUR ATP-R (BYPASS FOR 48*4 TRANSMISSION RANGE SWITCH R POSITION SIGNAL) 49 GRY BKSWNC (BRAKE PEDAL POSITION SWITCH) *2 RED PADDLE SW DOWN 50 (PADDLE SHIFTER － DOWNSHIFT SWITCH) PNK CLUTCH SW (CRUISE) 50*3 (CLUTCH PEDAL POSITION SWITCH) *1: With keyless access system *2: CVT (with paddle shifter) *3: M/T *4: CVT *5: M/T (with keyless access system,17 model) Page of Description Detects temperature control dial signal Detects clutch pedal position switch A signal Outputs transmission range switch P position signal Outputs transmission range switch R position signal Detects brake pedal position switch signal Detects paddle shifter － (downshift switch) signal Detects clutch pedal position switch signal PCM Inputs and Outputs at PCM Connector E (80P) Terminal number Wire color Not used LT GRN GRY WHT PNK Not used YEL Terminal name SO2HT (SECONDARY HEATED OXYGEN SENSOR (SECONDARY HO2S) (SENSOR 2) HEATER) Not used INJ1 (No. 1 INJECTOR) INJ4 (No. 4 INJECTOR) MTR 1 (THROTTLE ACTUATOR -SIDE) MTR 2 (THROTTLE ACTUATOR +SIDE) Not used Description Drives secondary HO2S (sensor 2) heater Sends No. 1 injector signal Sends No. 4 injector signal Ground for throttle actuator Drives throttle actuator https://biz.honda.co.jp/sip70/data/contents/sm/62T9AD90_2018_eng_EWD_20170630140 8/21/2017 PCM Connector for Inputs and Outputs 7139 Page of *3: M/T *4: CVT https://biz.honda.co.jp/sip70/data/contents/sm/62T9AD90_2018_eng_EWD_20170630140 8/21/2017 PCM Connector for Inputs and Outputs 7139 Terminal number 10 11*4 12 Wire color Not used Not used Not used GRN 13*4 Not used PUR 14 BLU 15 16 17 18 Not used BRN GRN TAN 19 20 Not used BLU 21 22 Not used RED 23 24 25*4 Not used Not used BLK 26*4 RED 27*4 LT GRN 28*4 BLU 29 LT GRN 30 WHT 31 32 33*4 Not used Not used RED 34*4 WHT 34*3 WHT Terminal name Page of Description Not used Not used Not used LCCLS (CVT LOCK-UP Drives CVT lock-up clutch control solenoid valve CLUTCH CONTROL SOLENOID VALVE) Not used DRLS (CVT DRIVE Drives CVT drive pulley control solenoid valve PULLEY CONTROL SOLENOID VALVE) AFHT (AIR FUEL RATIO Drives A/F sensor (sensor 1) heater (A/F) SENSOR (SENSOR 1) HEATER CONTROL) Not used INJ2 (No. 2 INJECTOR) Sends No. 2 injector signal INJ3 (No. 3 INJECTOR) Sends No. 3 injector signal PCS (EVAPORATIVE Drives EVAP canister purge valve EMISSION (EVAP) CANISTER PURGE VALVE) Not used CRKN GND Sensor ground for CKP sensor/CMP sensor (CRANKSHAFT POSITION (CKP) SENSOR/CAMSHAFT POSITION (CMP) SENSOR GROUND) Not used VTS (ROCKER ARM OIL Drives rocker arm oil control solenoid CONTROL SOLENOID) Not used Not used ATP GND Switch ground for transmission range switch (TRANSMISSION RANGE SWITCH GROUND) CPCLS (CVT CLUTCH Drives CVT clutch pressure control solenoid valve PRESSURE CONTROL SOLENOID VALVE) SH B (SHIFT SOLENOID Drives shift solenoid valve B VALVE B) DNLS (CVT DRIVEN Drives CVT driven pulley control solenoid valve PULLEY CONTROL SOLENOID VALVE) IGN03 (No. 3 IGNITION Drives No. 3 ignition coil COIL PULSE) IGN04 (No. 4 IGNITION Drives No. 4 ignition coil COIL PULSE) Not used Not used NDR (CVT DRIVE PULLEY Detects CVT drive pulley speed sensor SPEED SENSOR) VEL (CVT SPEED Detects CVT speed sensor signal SENSOR) NC (COUNTERSHAFT Detects output shaft (countershaft) speed sensor signal SPEED SENSOR) *3: M/T *4: CVT https://biz.honda.co.jp/sip70/data/contents/sm/62T9AD90_2018_eng_EWD_20170630140 8/21/2017 PCM Connector for Inputs and Outputs 7139 Terminal number 35 Wire color 36 YEL 37 38 Not used RED 39 40 41 42 Not used Not used BLU YEL 43 44 GRY TAN 45 46 GRY PNK 47 BLU 48*4 GRY 49*4 TAN 50*4 PNK 51 52*4 Not used LT GRN 53*4 LT BLU 54 BRN 55 PUR 56 LT GRN 57 58 59 60 Not used Not used Not used BRN GRN Terminal name Page of Description TDC (CAMSHAFT Detects CMP sensor signal POSITION (CMP) SENSOR) VGP (MASS AIR FLOW Detects MAF sensor signal (MAF) SENSOR +SIDE) Not used CRKN (CRANKSHAFT Detects CKP sensor signal POSITION (CKP) SENSOR) Not used Not used SG3 (SENSOR GROUND) Sensor ground VCC3 (SENSOR Provides sensor reference voltage VOLTAGE) LG1 (SENSOR GROUND) Sensor ground VCC2 (SENSOR Provides sensor reference voltage VOLTAGE) SG1 (SENSOR GROUND) Sensor ground VCC1 (SENSOR Provides sensor reference voltage VOLTAGE) IGN02 (No. 2 IGNITION Drives No. 2 ignition coil COIL PULSE) ATP-FWD Detects transmission range switch FWD position signal (TRANSMISSION RANGE SWITCH FWD POSITION) ATP-S (TRANSMISSION Detects transmission range switch S position signal RANGE SWITCH S POSITION) ATP-D (TRANSMISSION Detects transmission range switch D position signal RANGE SWITCH D POSITION) Not used NT (TORQUE Detects torque converter turbine speed sensor signal CONVERTER TURBINE SPEED SENSOR SIGNAL) TATF (ATF Detects ATF temperature sensor signal TEMPERATURE SENSOR) VGM (MASS AIR FLOW Ground for MAF sensor signal (MAF) SENSOR -SIDE) TA (INTAKE AIR Detects IAT sensor signal TEMPERATURE (IAT) SENSOR) TW (ENGINE COOLANT Detects ECT sensor signal TEMPERATURE (ECT) SENSOR) Not used Not used Not used SO2TSG (SECONDARY Sensor ground for secondary HO2S (sensor 2) HEATED OXYGEN SENSOR (SECONDARY HO2S (SENSOR 2)) SENSOR GROUND) *3: M/T *4: CVT https://biz.honda.co.jp/sip70/data/contents/sm/62T9AD90_2018_eng_EWD_20170630140 8/21/2017 PCM Connector for Inputs and Outputs 7139 Terminal number 61 Wire color 62 YEL 63 BLK 64 65 WHT PNK 66*4 GRN 67*4 BLU 68*4 RED 69*4 PUR 70*4 YEL 71*4 BLU 72 73 74 75 76 Not used Not used Not used Not used TAN 77 LT BLU 78 LT GRN 79 RED 80 TAN PNK Terminal name Page of Description SO2T (SECONDARY Detects secondary HO2S (sensor 2) signal HEATED OXYGEN SENSOR (SECONDARY HO2S) (SENSOR 2)) PB (MANIFOLD Detects MAP sensor signal ABSOLUTE PRESSURE (MAP) SENSOR) KS GND (KNOCK Sensor ground for knock sensor SENSOR GROUND) KS (KNOCK SENSOR) Detects knock sensor signal IGN01 (No. 1 IGNITION Drives No. 1 ignition coil COIL PULSE) ATP-RVS Detects transmission range switch RVS position signal (TRANSMISSION RANGE SWITCH RVS POSITION) ATP-L (TRANSMISSION Detects transmission range switch L position signal RANGE SWITCH L POSITION) ATPN (TRANSMISSION Detects transmission range switch N position signal RANGE SWITCH N POSITION) BP ATPP (TRANSMISSION Detects transmission range switch P position signal RANGE SWITCH P POSITION) BP ATP-R Detects transmission range switch R position signal (TRANSMISSION RANGE SWITCH R POSITION) PDN (CVT DRIVEN Detects CVT driven pulley pressure sensor signal PULLEY PRESSURE SENSOR) Not used Not used Not used Not used THL2 (THROTTLE Detects TP sensor B signal POSITION (TP) SENSOR B) AFS- (AIR FUEL RATIO Detects A/F sensor (sensor 1) signal (A/F) SENSOR (SENSOR 1) -SIDE) THL1 (THROTTLE Detects TP sensor A signal POSITION (TP) SENSOR A) AFS+ (AIR FUEL RATIO Detects A/F sensor (sensor 1) signal (A/F) SENSOR (SENSOR 1) +SIDE) ENGOPSW (OIL Detects engine oil pressure signal PRESSURE SWITCH) *3: M/T *4: CVT https://biz.honda.co.jp/sip70/data/contents/sm/62T9AD90_2018_eng_EWD_20170630140 8/21/2017 ... 8/ 21/ 2 017 PCM Connector for Inputs and Outputs 713 9 Terminal number 10 11 *4 12 Wire color Not used Not used Not used GRN 13 *4 Not used PUR 14 BLU 15 16 17 18 Not used BRN GRN TAN 19 20 Not used BLU 21. .. https://biz.honda.co.jp/sip70/data/contents/sm/62T9AD90_2 018 _eng_EWD_2 017 063 014 0 8/ 21/ 2 017 PCM Connector for Inputs and Outputs 713 9 Page of *3: M/T *4: CVT https://biz.honda.co.jp/sip70/data/contents/sm/62T9AD90_2 018 _eng_EWD_2 017 063 014 0 8/ 21/ 2 017 ... https://biz.honda.co.jp/sip70/data/contents/sm/62T9AD90_2 018 _eng_EWD_2 017 063 014 0 8/ 21/ 2 017 PCM Connector for Inputs and Outputs 713 9 Terminal number 61 Wire color 62 YEL 63 BLK 64 65 WHT PNK 66*4 GRN 67*4 BLU 68*4 RED 69*4 PUR 70*4 YEL 71* 4 BLU