B1.1 Function description The setting display of the CRT please refer to manual supplied from the controller builder CRT/MDI control panel： The controller panel including CRT and function key and power control push buttons。 ※ FANUC-0i-TC Power ON/OFF CRT10.4" display Function key B1.2 Element functions of machine operator panel Power switch：POWER ON Power switch：POWER OFF Cycle start push – button Feed hold: during the auto program running, the machine will stop cutting when the feed hold push button is pressed if the accident happened And the program can be resumed by push the cycle start push – button EMG STOP Emergency stop Data write protect switch: only when the switch is set to〝on〞the program could be edited, inserted or deleted Auto mode: when the mode selection switch is set to〝auto〞mode，the CRT would the program, and be executed Transmitting and working at the same time: Read out data through PC or CNC as turn the button to this position M.D.I mode: manual data input mode, and the parameters and program could be dited at this mode Handle mode: At the handle mode, the axis selection switch is fed by turning the pulse Handle。axis feed amount per pulse conforms to the setting of the handle switch JOG mode: Press directional button to axis-feed RAPID mode: Press directional button to move rapidly as Zero return Single block: when this switch is pressed, the indicator is lit, and automatic operation is executed by one block When the indicator is off, The program is executed continuously M01 stop: when the switch is pressed, the indicator is lit, and the machine will become feed hold when the block with M01 is executed Dry run: this function is used to check the program when this program Is executed at first time and it is valid only when the indicator lit Block skip: when the switch is pressed, the indicator is lit, and the block with the 〝/〞will be ignored Spindle JOG: To adjust spindle RPM by manual Spindle ccw rotate push button: spindle counter clockwise rotates, is equal to the M04 command Spindle stop push button: spindle stops rotates, is equal to the M05 command Spindle cw rotate push button: Spindle clockwise rotates, is equal to the M03 command C axis cw rotate push button C axis ccw rotate push button Press direction key with〝KEEP〞three second to move continuously To move X-axis in〝﹢〞direction To move X-axis in〝﹣〞direction To move Z-axis in〝﹢〞direction To move Z-axis in〝﹣〞direction Auto Shut-down Rest Apparatus: When this light is on , machine automatically shutdown while M30 code read in Spindle neutral gear indicator.﹙M40﹚ Spindle low gear indicator.﹙M41﹚ Spindle Middle gear indicator.﹙M42﹚ Spindle Middle-high gear indicator.﹙M43﹚ Spindle high gear indicator.﹙M44﹚ Chip conveyor switches: Press and move back Chip conveyor switches: Press to go forward continuously Press again to stop Tool changing push button In reserve key choose V12 Tools choose H4 Tools Coolant on/off switch Work lamp switch Machine lock: all the axes would not move, but the value of the coordinate will change on the screen Note: The zero return procedure should be done when turn off the function X axis zero return indicator: When X axis return to the zero position , the indicator will get lit Z axis zero return indicator: When Z axis return to the zero position , the indicator will get lit C axis zero return indicator: When C axis return to the zero position , the indicator will get lit Hydraulic chuck pilot lamp Selectivity program stop pilot lamp CNC alarm pilot lamp Lube alarm pilot lamp Coolant alarm pilot lamp Machinery alarm pilot lamp Hydraulic chuck open Hydraulic chuck close Program protect Program not protect Rapid feed rate override: F0 : 1% of the rapid feed rate F25 : 25% of the rapid feed rate F50 : 50% of the rapid feed rate F100: 100% of the rapid feed rate Spindle speed override switch: The switch is used to override the spindle speed For instance, if the spindle speed is 100 rpm in program, and the switch is set to 60%, then the spindle speed will reduce to 60 rpm Spindle speed adjustment switch: this switch at the jog or handle mode could adjust the spindle speed Note: Do not make change the spindle turn to opposite direction repeatedly, it will damage the gear JOG feed ride: The programmed feed rate is adjuration form to 150% in increments of 10% Mode selection button Turret indexing switch Load meter: Spindle load meter OT Over travel release: If X or Z axis over travel, press this button and use handle to move these axes Quá cữ hành trình Nếu trục X trục Z cữ, nhấn nút sử dụng chế dộ quay tay tạo xung đễ đưa Fast servomotor turrets to zero: Turn the tool switch to tool NO.1 and Choose V12 turret, Then put the tool change button