Belt grinder plans v1 Thiết kế máy mài dây đai

Belt Grinder -Backbone make one weld together, places ¼” x 2" flat bar cut a 1/16" x ¾” clearance slot the entire length on the inside of the ½” x 2" flat bar ½” x 2" flat bar 2.030" tap ½-20 0.530" ¼” x 2" flat bar file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 ¼” x 2" flat bar Belt Grinder -Bearing Plate make one Bearing Plate, 3/8" f;at bar weld the Backbone to the Bearing Plate take appropriate steps so that after welding this angle is precisely 90 degrees since it affects belt tracking drill appropriate pattern to mount two pillow block bearings to the plate 6.000" 7.000" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 Belt Grinder -Tracking Arm Bracket make one take appropriate steps so that after welding this angle is precisely 90 degrees since it affects belt tracking drill 0.500" 0.750" 6.500" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 weld ½” x 2" flat bar to the frame to form the tracking arm bracket Belt Grinder -Pedistal make one 1-1/2" square tubing with 3/16" or 1/4" wall drill and tap square tubing ½-20, then weld nut over the hole to increase the number of threads weld 1" x 0.250" wall DOM tubing to square tubing 2.000" 8.000" 33.000" Belt Grinder -Backbone and Pedistal Assembly make one weld Backbone to Pedistal Belt Grinder -Stand make one 10.000" 1-½” square tubing with 3/16" or ¼” wall electrical switch box 1" square bar 18.000" 10.000" 10.000" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 10.000" Belt Grinder -Tracking Adjustment Block make one ½” x 4" flat bar drill 0.250", places 1.000" 1.000" 1.000" 1.000" 0.500" 0.750" 3.000" tap 3/8-24 3.500" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 Belt Grinder -Tracking Adjustment Lever make one weld 1/2" x 1-½” flat bar to Tracking Adjustment Block drill 0.500" tap ¼-20 1.500" 8.000" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 Belt Grinder -Tracking Adjustment Arm make one 1.125" ½” x 2" flat bar, places drill 0.250" tap ½-13 weld two pieces together 0.250" 1.500" 3.000" 1.000" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 1.000" Belt Grinder -Vertical Platen Frame make one 3/8" x 6" flat bar tap ½-13, places 3/8" radius, drill 0.750" 1/4" radius, drill 0.500" Tap 3/8-16, places drill 0.500" 1.250" 2.250" 3.875" 4.250" 5.000" 5.750" 0.750" 1.125" 1.500" 1.750" 2.250" 3.000" 4.000" 6.000" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 Belt Grinder -Tool Rest make one 2.500" cut away this area 3" angle iron with ¼” wall 0.750" 0.750" tap ½-13 then weld a nut over the hole to increase the number of threads file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 Belt Grinder -Tool Rest Support Arm make one round end, places ½” square bar, places, welded together drill 0.500" 0.750" 2.500" 8.750" 9.500" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 Belt Grinder -Vertical Platen Extension Arm make one ½” x 2" flat bar tap ½-13, places 2.500" 21.000" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 Belt Grinder -Platen Clamp make one 3/8" x 1-½” flat bar drill 0.500", places 2.500" 4.000" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 Belt Grinder -Motor Mount make one drill 0.375" places 1.750" 0.750" 2.250" 7.000" drill 0.500", places ¼” x 1" flat bar, places 1.000" 4.875" 6.875" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 Belt Grinder -Vertical Platten Bracket make two tap ¼-20 and countersink 1.000" 1.50" 1.000" 5.000" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 Belt Grinder -Vertical Platten make one countersink all the way through, places 6.000" ¼” x 2" flat bar of stainless steel or other wear resistant material 4.250" 1.750" 1.000" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 1.000" [...]... Created 10/08/2011 Version 10/08/2011 Belt Grinder -Vertical Platen Extension Arm make one ½” x 2" flat bar tap ½-13, 2 places 2.500" 21.000" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 Belt Grinder -Platen Clamp make one 3/8" x 1-½” flat bar drill 0.500", 2 places 2.500" 4.000" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 Belt Grinder -Motor Mount make one drill 0.375".. .Belt Grinder -Tool Rest make one 2.500" cut away this area 3" angle iron with ¼” wall 0.750" 0.750" tap ½-13 then weld a nut over the hole to increase the number of threads file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 Belt Grinder -Tool Rest Support Arm make one round end, 2 places ½” square bar, 4 places, welded together drill 0.500" 0.750" 2.500" 8.750" 9.500" file = BeltGrinder1.vsd... 2.250" 7.000" drill 0.500", 2 places ¼” x 1" flat bar, 4 places 1.000" 4.875" 6.875" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 Belt Grinder -Vertical Platten Bracket make two tap ¼-20 and countersink 1.000" 1.50" 1.000" 5.000" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 Belt Grinder -Vertical Platten make one countersink all the way through, 2 places 6.000" ¼” x 2"... Version 10/08/2011 Belt Grinder -Vertical Platten make one countersink all the way through, 2 places 6.000" ¼” x 2" flat bar of stainless steel or other wear resistant material 4.250" 1.750" 1.000" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 1.000" ... 9.500" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 Belt Grinder -Vertical Platen Extension Arm make one ½” x 2" flat bar tap ½-13, places 2.500" 21.000" file = BeltGrinder1.vsd... Version 10/08/2011 Belt Grinder -Platen Clamp make one 3/8" x 1-½” flat bar drill 0.500", places 2.500" 4.000" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 Belt Grinder -Motor Mount... 6.875" file = BeltGrinder1.vsd Created 10/08/2011 Version 10/08/2011 Belt Grinder -Vertical Platten Bracket make two tap ¼-20 and countersink 1.000" 1.50" 1.000" 5.000" file = BeltGrinder1.vsd