giải pháp nhà thông minh

Intelligent Solutions This chapter shows two simplified examples of the use of Siemens instabus in the residential and the commercial buildings These examples serve as the method of documentation for your projects and, therefore, the features are kept to a minimum The following states the full documentation required for any one project: 1) Layout Drawings: Layout Drawings show the location where products are mounted in the building, to show the contractors where to install the products (e.g AP-, UP- and GE-type) If instabus products are mounted outside the distribution board, their mounting locations have to be indicated in this plan Siemens provides you with icons for flush mounted devices, surface mounted devices and devices that are incorporated in the equipment itself, that you can easily place them in your plan The layout plan also shows the basic routing of the wiring for the connection of the instabus devices as well as for the IR-Receivers Different lines (dashed, dotted) indicate a different cable type The routing of the 230V supply cabling is done by means of reference numbers For example, the index number for the lighting group 1.1.1 (5) means: This lighting group is connected to the instabus product with the number 1.1.1 You can find the details of this product in the Single Line Drawing of that project The number in brackets (5) indicates the terminal number of the product, so the contractor will have a reference of where to terminate the cable of this lighting group in the DB For AP-, UP- and GE-type products, separate icons are used to create Detail Drawings for termination references Intelligent Solutions: Necessary Documentation 4-47 A Residential Project 4-49 A Commercial Project .4-55 4-47 2) Single Line Drawings: The Single Line Drawings are used to plan the general concept of circuit protection and power distribution of the electrical system in a building The Siemens instabus products for distribution box mounting are designed to be mounted together with the circuit protection products in the same enclosure Therefore it is recommended to complete the single line drawings with the instabus EIB control devices mounted in the distribution boards Each page represents one rail in the distribution board The icons of the Siemens instabus products show the product name and all terminal connections to make planning easy and efficient The connections between circuit protection devices, DIN-rail mounted instabus devices and then to the load build a useful documentation of the design of the instabus installation The symbols and the physical instabus products can be labeled with an individual identification number (physical address) for cross reference to the Layout Drawings, for example: 1.1.1 The icon of this product also indicates the function of a dimmer N 527 Detailed technical information about the products can be found in the Technical Manual “Building Management with instabus EIB.” 3) Detail Drawings: The Detail Drawings show the terminal connections of the AP and GE type devices Detail Drawings are necessary to indicate the termination of the wires to the contractor on site When AP and GE type devices are used in a project and documented in the layout plan, one drawing per product type is sufficient Detailed technical information about the products can be found in the Technical Manual “Building Management with instabus EIB.” The icons used in these examples can be imported in the AutoCAD software and are ready to use Kindly contact your Siemens partner to get the latest Siemens instabus AutoCAD library for your office 4-48 Residential Project The residential area, in this example, is a one-storey house with three bedrooms, living/dining area and three bathrooms The features included in this example are simple: on/off switching with dimming and control via IR transmitter The home objects controlled by instabus EIB are the lights and two heaters There are two IR Receivers mounted in the ceiling: one in Bedroom and the other in the Living Hall They are connected to the IR decoder found in the Distribution Board and the line is represented by the dotted line IR Receivers not require physical addresses There are a total of 14 light circuits, heaters and set of shutters There are incandescent dimming circuits and florescent dimming circuits The following devices were specified: N 527 Universal Dimmer N 528 Universal Dimmer N 525 Switching/Dimming Actuator N 521 Shutter Actuator N 561 channel Binary Output N 510 channel Binary Output N 562 channel Binary Output N 450 IR Decoder S 440 IR Receiver N 122 Power Supply with Choke REG 190/01 Connector Data Rail 16 MW Number of Devices 2 2 1 2 4 Please refer to the Distribution Board drawings and the layout for correlation between light circuits and Siemens instabus products 4-49 Layout Drawing 4-50 Single Line Drawing 4-51 Single Line Drawing (Cont’d) 4-52 Single Line Drawing (Cont’d) 4-53 Single Line Drawing (Cont’d) 4-54 Commercial Project In this example, the areas which are looked into are: one meeting room, the lobby/corridor area and the offices Lobby/Corridor Area: For the lobby and corridor area, the lights are trigged on by Motion Detectors and will remain on for 40 minutes If further movement is detected within the 40 minutes, the timer will be re-set back to and the lights will remain on for a further 40 minutes Offices: All lights are controlled by a Push Button located at the entrance Only on/off switching is offered in this project The DIN rail mounted products for the office, lobby and corridor are found in Distribution Board The following devices are specified: In DB N 527 Universal Dimmer N 561 channel Binary Output N 302 Time Module N 122 Power Supply with Choke REG 190/01 Connector Data Rail 16 MW Number of Devices 1 1 2 Surface Mounted AP 600/01 channel Binary Output UP 250 Motion Detector UP 245 gang DELTA profil Push Button 3 Meeting Room: It is common that discussions and presentations are held in a meeting/conference room and to facilitate the change of one type of usage to another, Scene Control and Infra-Red Control have been added There are a total of lighting groups: groups of dimmable halogen lamps and group of dimmable florescent lamps A Handheld Transmitter is an added convenience to the users The following devices are specified: In DB N 527 Universal Dimmers N 450 IR Decoder N 300 Scene Module REG 190/01 Connector Number of Devices 1 Ceiling/Surface Mounted GE 525 Switching/Dimming Actuator (located in the light fitting itself) S 440 IR Receiver UP 212 gang DELTA studio push button AP 421 gang Handheld Transmitter 1 1 Points to note: • Only Power Supply is needed to supply power to the products as there are fewer than 64 programmable products in this project • The physical addresses for the devices must never be repeated for the same project Please refer to the drawings for the detailed connection between devices and load 4-55 Layout Drawing 4-56 Single Line Drawing 4-57 Single Line Drawing (Cont’d) 4-58 Single Line Drawing (Cont’d) 4-59 Detail Drawing DIMMER SWITCH (GE-TYPE) SWITCHING DEVICE (AP-TYPE) 4-60 4-61 4-62