A study on bottom spray granulation and its potential applications

A STUDY ON BOTTOM-SPRAY GRANULATION AND ITS POTENTIAL APPLICATIONS ER ZHI LIN DAWN NATIONAL UNIVERSITY OF SINGAPORE 2010 A STUDY ON BOTTOM-SPRAY GRANULATION AND ITS POTENTIAL APPLICATIONS ER ZHI LIN DAWN B.Sc. (Pharm.) Hons., NUS A THESIS SUBMITTED FOR THE DEGREE OF DOCTOR OF PHILOSOPHY DEPARTMENT OF PHARMACY NATIONAL UNIVERSITY OF SINGAPORE 2010 ACKNOWLEDGEMENTS I would like to express my heartfelt thanks to my supervisors, Asst. Prof Celine Liew and A/P Paul Heng for their guidance and the opportunities they have given me to learn and grow during the course of my study. I am indebted to NUS for providing me with a research scholarship to fund this higher degree, and to the Department of Pharmacy and its administrators for the facility and support during my candidature. I also wish to thank A/P Chan Lai Wah for her concern and advice throughout my candidature. Special thanks to Mrs Teresa Ang, Mr Peter Leong and Ms Wong Mei Yin, the laboratory technologists during my course of study for their technical assistance. I am fortunate to have been in the company of a group of supportive and helpful fellow postgraduates in GEA-NUS PPRL. They have made the laboratory a very pleasant and conducive place to work in. I would like to especially thank Elaine, Zhihui, Sook Mun, Yihui, Atul, Likun, Stephanie, Wun Chyi and Christine for their invaluable friendship. Finally, my deepest gratitude belongs to my dear family and friends, especially to my parents, for their faith and belief in me. I am grateful to my beloved husband, Dale, for his loving support and patience during this work. I will also like to thank my best friend, Serena, for her constant encouragement. Dawn, 2010 ii DEDICATION For my parents, Chin Lam and Hwee Kiang iii Table of contents TABLE OF CONTENTS ACKNOWLEDGEMENTS .ii DEDICATION . iii TABLE OF CONTENTS iv SUMMARY . x LIST OF TABLES .xii LIST OF FIGURES xiv LIST OF SYMBOLS .xvii I. INTRODUCTION . 2  A. BACKGROUND 2  A1. Significance of granulation . 2  A2. Types of granulation . 4  A2.1. Dry granulation processes . 4  A2.2. Wet granulation processes . 5  B. FLUIDIZED BED GRANULATION . 9  B1. Techniques of spray 11  B2. Advantages and challenges . 14  B3. Parameters influencing the process and granule quality . 16  B3.1. Material related factors 17  B3.2. Process related factors during the liquid binder addition phase . 20  B3.3. Process related factors during the drying phase 22  C. RECENT ADVANCES IN FLUIDIZED BED GRANULATION 25  C1. Process analytical technology (PAT) in fluidized bed granulation . 25  C1.1. Moisture content 26  iv Table of contents C1.2. Particle size 27  C1.3. Composition of bed material . 28  C1.4. Solid state transformations 28  C2. Fluidized bed granulation methods . 29  C2.1. Fluidized bed melt granulation 29  C2.2. Fluidized bed binderless granulation . 31  C2.3. Bottom-spray granulation 32  II. HYPOTHESIS AND OBJECTIVES 40  A. HYPOTHESIS 40  B. OBJECTIVES . 41  III. EXPERIMENTAL . 44  A. MATERIALS 44  A1. Feed material . 44  A2. Liquid binder . 44  A3. Model drugs 44  A4. Tablet excipients . 45  A5. Chemicals for dissolution media preparation and high performance liquid chromatography (HPLC) analyses . 46  B. METHODS . 47  B1. Feed material . 47  B1.1. Blending of powder . 48  B1.2. Determination of powder particle size . 48  B1.3. Determination of powder flow with angle of repose . 48  B2. Liquid binder . 49  B2.1. Micronization of HCT . 49  v Table of contents B2.2. Determination of particle size of micronized HCT . 50  B2.3. Preparation of HCT-incorporated liquid binder 50  B3. Granulation process . 50  B3.1. Real-time measurement of process conditions 52  B3.2. Determination of process drying efficiency 54  B3.3. Determination of granule bed temperature profiles . 54  B3.4. Determination of capacity for moisture removal . 55  B3.5. Determination of granule bed moisture content profiles . 55  B3.6. Determination of air velocity within partition column 56  B3.7. Determination of process yield 56  B4. Characterization of granules 57  B4.1. Granule size . 57  B4.2. Granule shape 57  B4.3. Granule surface morphology . 58  B4.4. Granule flow 58  B4.5. Granule porosity 59  B4.6. Granule friability . 59  B4.7. Content determination of HCT in granules . 60  B4.8. Dissolution of HCT from granules 61  B4.9. Amount of ASA degradation . 61  B5. Compaction process 63  B5.1. Heckel plot analysis . 64  B6. Characterization of tablets . 65  B6.1. Tablet surface morphology and roughness 65  B6.2. Tablet porosity . 66  vi Table of contents B6.3. Tablet tensile strength 67  B6.4. Disintegration of tablets . 67  B6.5. Dissolution of HCT from tablets . 67  B7. Statistical analyses . 68  B7.1. Design-of-Experiment and response surface modelling 68  B7.2. Multivariate data analysis 69  B7.3. Regression analyses . 69  B7.4. Other data analyses 70  B7.5. Level of significance 70  IV. RESULTS AND DISCUSSION . 72  A. ROLE OF FLUID DYNAMICS AND WETTING ON GRANULE FORMATION IN PG 72  A1. Factors influencing air velocity within the partition column 73  A2. Factors influencing characteristics of granule batches . 77  A2.1. Influence of variables on process yield . 77  A2.2. Influence of variables on granule size and size distribution 85  A2.2.1. Influence of variables on fines . 85  A2.2.2. Influence of variables on lumps . 88  A2.2.3. Influence of variables on modal size fraction 89  A2.2.4. Influence of variables on MMD . 89  A2.2.5. Influence of variables on span . 91  A2.3. Influence of variables on granule shape 91  A2.4. Influence of variables on granule flow 95  B. APPLICABILITY OF PG AND TG FOR SPRAY DEPOSITION OF DRUG DURING GRANULATION . 96  vii Table of contents B1. Drug content and drug content uniformity of PG and TG granules 96  B2. Impact of particle circulation pattern and fluid dynamics in PG and TG on granule growth 99  B2.1. Resultant mode of granule growth in PG and TG . 102  B2.2. Process sensitivity to binder spray rate and the resultant influences on granule growth . 106  B2.3. Process sensitivity to particle size of feed material and the resultant influences on granule growth . 112  B3. Drug release properties of PG and TG granules . 117  B4. Flow properties of PG and TG granules 119  C. COMPACTIBILITY STUDY ON PG AND TG GRANULES . 120  C1. Compaction behaviour of PG and TG granules 120  C1.1. Influence of compactibility of granules on tablet properties . 126  C1.2. General relation between granule characteristics, granule compactibility and tablet properties . 136  C2. Compaction behaviour of PG and TG granules with tablet excipients . 142  C2.1. Influence of compactibility of granules on disintegrant efficacy . 145  D. INVESTIGATIVE STUDY ON THE ABILITY OF PG TO GRANULATE MOISTURE SENSITIVE DRUGS 150  D1. ASA stability in PG and TG during processing 150  D1.1. Impact of particle circulation pattern and fluid dynamics in PG and TG on ASA stability 155  D1.2. Influence of inlet air temperature and binder spray rate 158  viii Table of contents D2. Factors influencing processing conditions and ASA stability in PG 161  D2.1. Influence of AAI diameter . 163  D2.2. Influence of inlet air temperature 164  D2.3. Influence of binder spray rate 165  V. CONCLUSION . 168  VI. REFERENCES . 172  VII. LIST OF PUBLICATIONS 211  ix References Rasanen, E., Rantanen, J., Jorgensen, A., Karjalainen, M., Paakkari, T., Yliruusi, J., 2001. Novel identification of pseudopolymorphic changes of theophylline during wet granulation using near infrared spectroscopy. J. Pharm. Sci. 90(3), 389-396. Ritala, M., Jungersen, O., Holm, P., Schaefer, T., Kristensen, H.G., 1986. A comparison between binders in the wet phase of granulation in a high shear mixer. Drug Dev. Ind. Pharm. 12(11-13), 1685-1700. Rodriguez, L., 2002. Preparation and characterization by morphological analysis of diclofenac/PEG 4000 granules obtained using three different techniques. Int. J. Pharm. 242(1-2), 285-289. Rohera, B.D., Zahir, A., 1993. Granulations in a fluidized bed: Effect of binders and their concentrations on granule growth and modelling the relationship between granule size and binder concentration. Drug Dev. Ind. Pharm. 19(7), 773-792 Romer., M., Heinamaki, J., Miroshnyk, I., Kivikero, N., Sandler, N., Rantanen, J., Yliruusi, J., 2008. Phase transformation of erythromycin A dihydrate during fluid bed drying. J. Pharm. Sci. 97(9), 4020-4029. Rubino, O.P., 1999. Fluid-bed technology. Overview and criteria for process selection. Pharm. Technol. 23(6), 104-113. 197 References Sakkinen, M., Seppala, U., Heinanen, P., Marvola, M., 2002. In vitro evaluation of microcrystalline chitosan (MCCh) as gel-forming excipients in matrix granules. Eur. J. Pharm. Biopharm. 54(1), 33-40. Sastry, K.V.S., Fuerstenau, D.W., 1973. Mechanisms of agglomerate growth in green pelletization. Powder Technol. 7(2), 97-105. Schaafsma, S.H., Kossen, N.W.F., Mos, M.T., Blauw, L., Hoffmann, A.C., 1999. Effects and control of humidity and particle mixing in fluid-bed granulation. AIChE. J. 45(6), 1202-1210. Schaafsma, S.H., Marx, T., Hoffmann, A.C., 2006. Investigation of the particle flowpattern and segregation in tapered fluidized bed granulators. Chem. Eng. Sci. 61(14), 4467-4475. Schaafsma, S.H., Vonk, P., Kossen, N.W.F., 2000. Fluid bed agglomeration with a narrow droplet size distribution. Int. J. Pharm. 193(2), 175-187. Schaefer, T., Worts, O., 1978. Control of fluidized bed granulation. IV. Effects of binder solution and atomization on granule size and size distribution. Arch. Pharm. Sci. Ed. 6, 14-25. 198 References Schiller, M., Von der Heydth, H., Marz, F., Schmidt, P.C., 2003. Enhanced processing properties and stability of film-coated tablets prepared from roller-compacted and ionexchanged Eschscholtzia californica Cham. dry extracts. S.T.P. Pharma. Sci. 13(2), 111-117. Schwartz, J.B., 1988. Granulation. Drug Dev. Ind. Pharm. 14(14), 2071-2090. Schinzinger, O., Schmidt, P.C., 2005. Comparison of the granulation behaviour of three different excipients in a laboratory fluidized bed granulator using statistical methods. Pharm. Dev. Technol. 10(2), 175-188. Senadeera, W., Bhandari, B.R., Young, G., Wijesinghe, B., 2003. Influences of shapes of selected vegetable materials on drying kinetics during fluidized bed drying. J. Food Eng. 58(3), 277-283. Seo, A., Holm, P., Kristensen, H.G., Schaefer, T., 2003. The preparation of agglomerates containing solid dispersions of diazepam by melt agglomeration in a high shear mixer. Int. J. Pharm. 259 (1-2), 161-171. Shallcross, D.C., 1997. Psychrometric charts. In: D.C. Shallcross (Ed.), Handbook of psychometric charts: humidity diagrams for engineers. London: Blackie Academic and Professional, 44-45. 199 References Shangraw R.F., 1990. Compressed tablets by direct compression. In: Lieberman, H.A., Lachman, L., Schwartz, J.B (Eds.), Pharmaceutical dosage forms: tablets vol. 1. 2nd Ed. New York: Marcel Dekker, 195-245. Shangraw, R.F., Wallace, J.W., Bowers, F.M., 1981. Morphology and functionality in tablet excipients for direct compression. Part 2. Pharm. Technol. 5(10), 44-60. Simons, S.J.R., Fairbrother, R.J., 2000. Direct observations of liquid binder-particle interactions: the role of wetting behaviour in agglomerate growth. Powder Technol. 110(1-2), 44-58. Skinner, G.W., Harcum, W.W., Barnum, P.E., Guo, J., 1999. The evaluation of fineparticle hydroxypropylcellulose as a roller compaction binder in pharmaceutical applications. Drug Dev. Ind. Pharm. 25(10), 1121-1128. Soares, L.A.L., Ortega, G.G., Petrovick, P.R., Schmidt, P.C., 2005. Dry granulation and compression of spray-dried plant extracts. AAPS PharmSciTech. 6(3), E359E366. Some, I.T., Bogaerts, P., Hanus, R., Hanocq, M., Dubois, J., 2000. Improved kinetic parameter estimation in pH-profile data treatment. Int. J. Pharm. 198(1), 39-49. Song, H.B., Kim, Y.T., Kim, S.D., 1997. Circulation of solids and gas bypassing in an internally circulating fluidized bed with a draft tube. Chem. Eng. J. 68 (2-3), 115–122. 200 References Stahl, H., 2004. Comparing different granulation techniques. Pharm. Technol. Eur. 16(11), 23-33. Stanley-Wood, N.G., 1990. Size enlargement. In: Rhodes, M.J., (Ed.), Principles of powder technology. Chichester: John Wiley and Sons, 193-226. Stepanek, F., Rajniak, P., Mancinelli, C., Chern, R.T., Ramachandran, R., 2009. Distribution and accessibility of binder in wet granules. Powder Technol. 189(2), 376384. Summers, M., Aulton, M., 2001. Granulation. In: Aulton, M.E., (Ed.), Pharmaceutics. The science of dosage form design. 2nd Ed. Spain: Churchill Livingstone, 364-378. Sun, C., Grant, D.J.W., 2001. Influence of elastic deformation of particles on Heckel analysis. Pharm. Dev. Technol. 6(2), 193-200. Takano, K., Nishii, K., Horio, M., 2003. Binderless granulation of pharmaceutical fine powders with coarse lactose for dry powder inhalation. Powder Technol. 131(23), 129-138. Takano, K., Nishii, K., Mukoyama, A., Iwadate, Y., Kamiya, H., Horio, M., 2002. Binderless granulation of pharmaceutical lactose powders. Powder Technol. 122(2-3), 212-221. 201 References Tan, H.S., Salman, A,D., Hounslow, M.J., 2004. Kinetics of fluidized bed melt granulation IV: Selecting the breakage model. Powder Technol. 143-144, 65-83. Tan, H.S., Salman, A,D., Hounslow, M.J., 2005a. Kinetics of fluidized bed melt granulation III: Tracer studies. Chem. Eng. Sci. 60(14), 3835-3845. Tan, H.S., Salman, A,D., Hounslow, M.J., 2005b. Kinetics of fluidized bed melt granulation V: Simultaneous modeling of aggregation and breakage. Chem. Eng. Sci. 60(14), 3847-3866. Tan, H.S., Salman, A,D., Hounslow, M.J., 2006a. Kinetics of fluidized bed melt granulation I: The effect of process variables. Chem. Eng. Sci. 61(5), 1585-1601. Tan, H.S., Salman, A,D., Hounslow, M.J., 2006b. Kinetics of fluidized bed melt granulation V: Modeling the net rate of growth. Chem. Eng. Sci. 61(5), 3930-3941. Tang, E.S.K., Wang, L., Liew, C.V., Chan, L.W., Heng, P.W.S., 2008. Drying efficiency and particle movement in coating – impact on particle agglomeration and yield. Int. J. Pharm. 350(1-2), 172-180. Thies, R., Kleinebudde, P., 1999. Melt pelletisation of a hygroscopic drug in a high shear mixer. Part 1. Influence of process variables. Int. J. Pharm. 188(2), 131-143. 202 References Tobyn, M.J., Staniforth, J.N., Baichwal, A.R., McCall, T.W., 1996. Prediction of physical properties of a novel polysaccharide controlled release system. I. Int. J. Pharm. 128(1), 113-122. Tomuta, I., Alecu, C., Rus, L.L., Lecuta, S.E., 2009. Optimization of fluid bed formulations of metoprolol granules and tablets using an experimental design. Drug Dev. Ind. Pharm. 35(9), 1072-1081. Tsutsumi, A., Suzuki, H., Saito, Y., Yoshida, K., Yamazaki, R., 1998. Multicomponent granulation is a fast fluidized bed. Powder Technol. 100(2-3), 237-241. Turton, R., Tardos, G.I., Ennis, B.J., 1999. Fluidized bed coating and granulation. In: W. Yang (Ed.), Fluidization solids handling and processing: industrial applications. New Jersey: Noyes Publications, 331-434. Vaithiyalingam, S.R., Tuliani, P., Wilber, W., Reddy, I.K., Khan, M.A., 2002. Formulation and stability evaluation of ketoprofen sustained-release tablets prepared by fluid bed granulation with Carbopol® 971P solution. Drug Dev. Ind. Pharm. 28(10), 1231-1240. Van der Zwan, J., Siskens, C.A.M., 1982. The compaction and mechanical properties of agglomerated materials. Powder Technol. 33(1), 43-54. 203 References Vilhelmsen, T., Eliasen, H., Schaefer, T., 2005. Effect of a melt agglomeration process on agglomerates containing solid dispersions. Int. J. Pharm. 303(1-2), 132142. Walker, G.M., Holland, C.R., Ahmad, M.M.N., Craig, D.Q.M., 2005. Influence of process parameters on fluidized hot-melt granulation and tablet pressing of pharmaceutical powders. Chem. Eng. Sci. 60(14), 3867-3877. Walker, G.M., Andrews, G., Jones, D., 2006. Effect of process parameters on the melt granulation of pharmaceutical powders. Powder Technol. 165(3), 161-166. Walker, G.M, Bell, S.E.J., Andrews, G., Jones, D., 2007a. Co-melt fluidized bed granulation of pharmaceutical powders: Improvements in drug bioavailability. Chem. Eng. Sci. 62 (1-2), 451-462. Walker, G.M., Bell, S.E.J., Vann, M., Jones, D.S., Andrews, G., 2007b. Fluidized bed characterization using Ramen spectroscopy: Applications to pharmaceutical processing. Chem. Eng. Sci. 62(14), 3832-3838. Walker, G.M., Bell, S.E.J., Greene, K., Jones, D.S., Andrews, G.P., 2009. Characterization of fluidized bed granulation processes using in-situ Ramen spectroscopy. Chem. Eng. Sci. 64(1), 91-98. Walter, K.T., 2002. Precision granulation. United States Patent 6,492,024 B1. 204 References Walter, K.T., Liew, C., Brzeczko, A. W., 2003. Fluidized bed precision granulation™ with real time process determination™. AAPS poster presentation, Salt Lake City, Utah, US. Wan, L.S.C., Heng, P.W.S., Liew, C.V., 1995. The influence of liquid spray rate and atomizing pressure on the size of spray droplets and spheroids. Int. J. Pharm. 118(2) 213-219, Wan, L.S.C., Heng, P.W.S., Ling, B.L., 1995. Fluidized bed granulation with PVP K90 and PVP K120. Drug Dev. Ind. Pharm. 21(7), 857-862. Wan, L.S.C., Heng, P.W.S., Ling, B.L., 1996. Effect of polyvinylpyrrolidone solutions containing dissolved drug on characteristics of lactose fluidized bed granules. Int. J. Pharm. 141(1), 161-170. Wan, L.S.C., Heng, P.W.S., Muhuri, G., 1992. Incorporation and distribution of a low dose drug in granules. Int. J. Pharm. 88(1-3), 159-163. Wan, L.S.C., Lim, K.S., 1988. The effect of incorporating polyvinylpyrrolidone as a binder on fluidized bed granulations of lactose. S.T.P. Pharma. Sci. 4(7), 560-571. Wan, L.S.C., Lim, K.S., 1989. Mode of action of polyvinylpyrrolidone as a binder on fluidized bed granulation of lactose and starch granules. S.T.P. Pharma. Sci. 5(4), 244-250. 205 References Wang, X., Cui, F., Yonezawa, Y., Sunada, H., 2003. Preparation and evaluation of high drug content particles. Drug Dev. Ind. Pharm. 29(10), 1109-1118. Watano, S., 2001. Direct control of wet granulation processes by image processing system. Powder Technol. 117(1-2), 163-172. Watano, S., Sato, Y., Miyanami, K., 1995. Image processing for on-line monitoring of granule size distribution and shape in fluidized bed granulation. Powder Technol. 83(11), 55-60. Watano, S., Takashima, H., Miyanami, K., 1997. Scale-up of agitation fluidized bed granulation. V. Effect of moisture content on scale-up characteristics. Chem. Pharm. Bull. 45(4), 710-714. Watano, S., Takashima, H., Sato, Y., Yasutomo, T., Miyanami, K., 1996. Measurement of moisture content by IR sensor in fluidized bed granulation. Effects of operating variables on the relationship between granule moisture content and absorbance of IR spectra. Chem. Pharm. Bull. 44(6), 1267-1269. Wells, J.I., Walker, C.V., 1983. The influence of granulating fluids upon granule and tablet properties: The role of secondary binding. Int. J. Pharm. 15(1), 97-111. Wildfong, P.L.D., Samy, A., Corfa, J., Peck, G.E., Morris, K.R., 2002. Accelerated fluid bed drying using NIR monitoring and phenomenological modeling: Method assessment and formulation stability. J. Pharm. Sci. 91(3), 631-639. 206 References Wikberg, M., Alderborn, G., 1991. Compression characteristics of granulated materials. IV. The effect of granule porosity on the fragmentation propensity and the compactibility of some granulations. Int. J. Pharm. 69(3), 239-253. Wong, T.W., Cheong, W.S., Heng, P.W.S., 2005. Melt granulation and pelletization. In: Parikh, D.M., (Ed.), Handbook of Pharmaceutical Granulation Technology. 2nd Ed. New York: Taylor and Francis, 385-406. Wostheinrich, K., Schmidt, P.C., 2000. Evaluation and validation of a fully instrumented Huttlin HKC 05-TJ laboratory scale fluidized bed granulator. Drug Dev. Ind. Pharm. 26(6), 621-633. Wormsbecker, M., Ommen, R., Nijenhuis, J., Tanfara, H., Pugsley, T., 2009. The influence of vessel geometry on fluidized bed dryer hydrodynamics. Powder Technol. 194(1-2), 115-125. Wormsbecker, M., Pugsley, T., 2008. The influence of moisture on the fluidization behaviour of porous pharmaceutical granule. Chem. Eng. Sci. 63(16), 4063-4069. Wurster, D.E., 1959. Air suspension technique of coating drug particles: A preliminary report. J. Am. Pharm. Assoc. 48(8), 451-454. Yang, D., Kulkarni, R., Behme, R.J., Kotiyan, P.N., 2007. Effect of the melt granulation on the dissolution characteristics of griseofulvin. Int. J. Pharm. 329(1-2), 72-80. 207 References Yang, S.T., Savage, G.V., Weiss, Jay., Ghebre-Sellassie, I., 1992. The effect of spray mode and chamber geometry of fluid-bed coating equipment and other parameters on an aqueous-based ethylcellulose coating. Int. J. Pharm. 86 (2-3), 247-257. Yang, W., Brooke, D., 1982. Rate equation for solid state decomposition of aspirin in the presence of moisture. Int. J. Pharm. 11(3), 271-276. Yanze, F.M., Duru, C., Jacob, M., 2000. A process to produce effervescent tablets: fluidized bed dryer melt granulation. Drug Dev. Ind. Pharm. 26(11), 1167-1176. York, P., 1978. Particle slippage and rearrangement during compression of pharmaceutical powders. J. Pharm. Pharmacol. 30(1), 6-10. Yuksel, N., Karatas, A., Baykara, T., 2003. Comparative evaluation of granules made with different binders by a fluidized bed method. Drug Dev. Ind. Pharm. 29(4), 387395. Zhang, G.G.Z., Law, D., Schmitt, E.A., Qiu, Y., 2004. Phase transformation considerations during process development and manufacture of solid oral dosage forms. Adv. Drug Deliv. Rev. 56(3), 371-390. Zhao, N., Augsburger, L.L., 2005. The influence of swelling capacity of superdisintegrants in different pH media on the dissolution of hydrochlorothiazide from directly compressed tablets. AAPS PharmSciTech. 6(1), E19. 208 References Zoglio, M.A., Streng, W.H., Carstensen, J.T., 1975. Diffusion model for fluidized-bed drying. J. Pharm. Sci. 64(11), 1869-1873. Zuurman, K., Riepma, K.A., Bolhuis, G.K., Vromans, H., Lerk, C.F., 1994. The relationship between bulk density and compactibility of lactose granulations. Int. J. Pharm., 102(1-3), 1-9. 209 PART VII: LIST OF PUBLICATIONS 210 List of publications VII. LIST OF PUBLICATIONS Journal publications 1. Liew, C.V., Er, D.Z.L., Heng, P.W.S., 2009. Air-dictated bottom spray process: Impact of fluid dynamics on granule growth and morphology. Drug Dev. Ind. Pharm. 35(7), 866-876. 2. Er, D.Z.L., Liew, C.V., Heng, P.W.S., 2009. Layered growth with bottom-spray granulation for spray deposition of drug. Int. J. Pharm. 377(1-2), 16-24. Conference presentations 1. Er, D.Z.L., Liew, C.V., Heng, P.W.S. A comparative study on the compactibility of granules prepared by bottom-spray and top-spray granulation. Poster presentation. American Association of Pharmaceutical Scientists (AAPS) Annual Meeting and Exposition 2009, 8th to 12th November 2009, Los Angeles, California, USA. 2. Er, D.Z.L., Liew, C.V., Heng, P.W.S. Air-dictated bottom spray process for granulation of moisture sensitive drugs. Oral presentation. ASEAN Scientific Conference in Pharmaceutical Technology 2008, 1st to 3rd June 2008, Penang, Malaysia. 3. Er, D.Z.L., Liew, C.V., Heng, P.W.S. A study on granule growth behaviour in top and bottom fluidized bed granulations. Poster presentation. Asian Association of Colleges of Pharmacy (AASP) Conference 2007, 25th to 28th October 2007, Makati City, Philippines. 211 List of publications 4. Ng, Y., Er, D.Z.L., Liew, C.V., Heng, P.W.S. Influence of the characteristics of starting material on fluidized bed granules properties. Poster presentation. 2nd AAPS-NUS Student Chapter Symposium, 5th March 2007, Singapore. 5. Er, D.Z.L., Liew, C.V., Heng, P.W.S. Precision granulation: a promising bottom spray fluid bed granulation process. Poster presentation. Asian Pharmaceutics Graduate Congress, 25th to 27th September 2006, Singapore. 6. Er, D.Z.L., Liew, C.V., Heng, P.W.S. A comparative study of the influence of fluid dynamics and thermodynamics on the properties of granules prepared by precision granulation. Poster presentation. American Association of Pharmaceutical Scientists (AAPS) Annual Meeting and Exposition 2006, 29th October to 2nd November 2006, San Antonio, Texas, USA. 7. Er, D.Z.L., Liew, C.V., Heng, P.W.S. Cocurrent and countercurrent binder spray orientation on growth kinetics in fluid bed granulation processes. Poster presentation. Asian Association of Colleges of Pharmacy (AASP) Conference 2005, 14th to 17th November 2005, Bangkok, Thailand. 212 [...]... linear term (partition gap) in response surface equation XS linear term (binder spray rate) in response surface equation XAA squared term (air accelerator insert × air accelerator insert) in response surface equation XPP squared term (partition gap × partition gap) in response surface equation XSS squared term (binder spray rate × binder spray rate) in response surface equation XAP interaction term (air... in which a positive correlation to granule size was exhibited The partition gap played an important role in transporting particles into the spray granulation zone, whereas the binder spray rate affected granule shape Unlike conventional top -spray granulation, fluid dynamics in the bottom- spray process can be easily modulated by using different air accelerator inserts and partition gaps to allow for... (air accelerator insert × partition gap) in response surface equation xix List of symbols XAS interaction term (air accelerator insert × binder spray rate) in response surface equation XPS interaction term (partition gap × binder spray rate) in response surface equation Xaf linear term (airflow rate) in regression equation XAAI linear term (air accelerator insert) in regression equation Xheat linear... of (a) AAI diameter and partition gap (hold values at binder spray rate = 21 g/min) and (b) binder spray rate and partition gap (hold values at AAI diameter = 29.5 mm) on aspect ratio 93 Figure 13 Mean drug content of PG and TG granules: PG/small ( ), PG/medium ( ), PG/large ( ), TG/small ( ), TG/medium ( ) and TG/large ( ) when (a) binder spray rate and (b) lactose powder blend were varied... practical application, attributed to inherent problems such as loss in compactibility (Li and Peck, 1990) and poor homogeneity of the formed compact (Badawy et al., 1999) A2 .2 Wet granulation processes Some common examples of wet granulation processes include wet massing, high shear granulation, pan granulation, extrusion-spheronization, spray drying and fluidized bed granulation Of particular interest... postioned at side of chamber Perforated metal plate Powder particles Rotating plate Fluidizing air Gap air (c) Product chamber Partition column Powder particles Perforated air distribution plate Fluidizing air Spray nozzle positioned at bottom of chamber Figure 3 Schematic diagrams of (a) top -spray granulator, (b) tangential -spray granulator: double chamber rotary processor and (c) bottom- spray granulator... commonly present and its presence better regulates particle fluidization and flow into the spray granulation zone (Ishida and Shirai, 1975) Binder solution is sprayed in the same direction as the air flow Essentially employed for coating purposes and less so for granulation (Dixit and Puthli, 2009), there were few reports on its use for pharmaceutical granulation in the 1990s (Flogel and Egermann,... granulation of inorganic materials (Freitag and Kleinebudde, 2003), granulation of dry herbal materials (EggelkrautGottanka et al., 2002; Soares et al., 2005), compaction of tablet formulations (Mollan and Celik, 1996; Skinner et al., 1999) and production of controlled release formulations (Ohmori and Makino, 2000; Juang and Storey, 2003; Mitchell et al., 2003) However, there are limitations to its practical... increases, particle deformation occurs and creates more points of contact for bonding to occur With an additional increase in the 4 Introduction compaction force, fragmentation of particles takes place and the number of potential bonding sites is further increased Lastly, particle-particle bonding results, together with plastic deformation and fragmentation Roller compaction has found application in the granulation. .. have understandably gained more attention 3 Introduction A2 Types of granulation Several manufacturing techniques are used for producing granules, and they can be broadly divided into dry and wet granulation processes A2 .1 Dry granulation processes In dry granulation processes, power particles are brought together by mechanical force The binders used exist in solid form A major advantage of dry granulation . A STUDY ON BOTTOM-SPRAY GRANULATION AND ITS POTENTIAL APPLICATIONS ER ZHI LIN DAWN NATIONAL UNIVERSITY OF SINGAPORE 2010 A STUDY ON BOTTOM-SPRAY. factorial design. 78 Figure 11. Response surface graphs of the effect of (a) AAI diameter and binder spray rate (hold values at partition gap = 26 mm) on fines and (b) AAI diameter and partition. granulation 2 A2 . Types of granulation 4 A2 .1. Dry granulation processes 4 A2 .2. Wet granulation processes 5 B. FLUIDIZED BED GRANULATION 9 B1. Techniques of spray 11 B2. Advantages and challenges