Early strength development of cement mixed singapore marine clay

EARLY STRENGTH DEVELOPMENT OF CEMENT MIXED SINGAPORE MARINE CLAY LU YITAN NATIONAL UNIVERSITY OF SINGAPORE 2014 EARLY STRENGTH DEVELOPMENT OF CEMENT MIXED SINGAPORE MARINE CLAY LU YITAN (B.Eng. (Hons), NTU ) A THESIS SUBMITTED FOR THE DEGREE OF DOCTOR OF PHILOSOPHY DEPARTMENT OF CIVIL AND ENVIRONMENTAL ENGINEERING NATIONAL UNIVERSITY OF SINGAPORE 2014 Declaration I hereby declare that this thesis is my original work and it has been written by me in its entirety. I have duly acknowledged all the sources of information which have been used in the thesis. This thesis has also not been submitted for any degree in any university previously. /lF April It,20L4 Abstract In land scarce Singapore, the use of cement mixed clay as reclamation fill resolves not only the shortage of dumping ground for unwanted soil disposal, but also the shortage of fill for land reclamation. This innovative scheme of using cement mixed clay always involves massive volume of construction at high rate of production. Thus, effective early quality control (QC) measures play an pivotal role in the successful implementation of this scheme. In a recent project in Singapore, cement mixed Singapore marine clay has been used as fill to build a containment bund. This research was set out to devise an effective early QC technique for the cement mixed clay fill in the containment bund construction. The early strength behavior of cement mixed Singapore marine clay was first investigated in an experimental study. The transition behavior in the early strength development and the corresponding reaction heat evolution suggest that cement mixed Singapore marine clay exhibits setting behavior in the initial stage of curing like any other cementitious material. In this investigation, the effect of curing temperature on the early strength behavior was also studied. It was found that the setting time reduces at a higher curing temperature. The relation between setting time and curing temperature was found to be governed by the Arrhenius law, and this relation was validated by literature data of concrete/mortar. The effect of curing temperature on the long-term strength development was also investigated. It was found that cement mixed Singapore marine clay develops higher ultimate strengths under higher curing temperatures. This behavior is different from the commonly observed “crossover” behavior for concrete/mortar or cement mixed granular soils, in which the ultimate strengths developed under different curing temperatures are about the same. Due to this difference, the model developed by Chitambira (2004) was modified by introducing a proposed strength enhancing factor ηT and adopting a modified shift factor aT . By making these modifications, the effect of curing temperature on both the ultimate strength and rate of strength gain can be accounted for. Moreover, both ln ηT and i aT show Arrhenius-type relation with the curing temperature T . The proposed model in this study was validated by independent tests and literature data. Thus, the strengths developed under different curing temperatures can be fundamentally related. An accelerated strength test based on elevated temperature curing was proposed in this study as an early QC technique. The rationale behind this proposal is that the setting process can be shortened by the elevated temperature, and that the strengths developed under different temperatures are fundamentally related. Accelerated tests were conducted independently in this study. The test results suggest that the strength obtained in the accelerated test [qu (acc)] is governed by the similar fundamental strength mechanisms of 7-day or 28-day strength [qu (7day) or qu (28day)] obtained in the standard room temperature curing condition. The strong correlation of qu (7day) – qu (acc) or qu (28day) – qu (acc) can be used for the early QC of cement mixed Singapore marine clay. Therefore, the applicability of the proposed accelerated test is validated. KEYWORDS: quality control, cement mixed clay, land reclamation, setting, curing temperature, Arrhenius law. ii Acknowledgment First and foremost, I would like to express my most sincere and heartfelt gratitude to Professor Tan Thiam Soon for his invaluable guidance, and utmost patience throughout the entire course of my PhD study. I would not have completed this thesis without Prof Tan’s contribution. I wish to thank Professor Phoon Kok Kwang for his suggestions and continuous support in various stages of this research. It has always been pleasant and great learning experience for me to discuss with him various issues in technical and non-technical fields. I would like to thank Dr Zhang Rongjun for his help in my laboratory tests, for the many long and stimulating discussions and for good friendship. I would also like to thank Dr Surendra Tamrakar for his help in setting up various laboratory instruments in the initial stage of this research and for his friendship. My sincere thanks must go to Dr Darren Chian Siau Chen and Professor Leung Chun Fai, both of whom are members of my thesis examination committee, for providing me with in-depth and professional review comments to improve my thesis. I thank Professor Lee Fook Hou, Dr Goh Siang Huat and Associate Professor Harry Tan Siew Ann for sharing with me their expert advices and opinions on my research. I am grateful to my former mentor, Associate Professor Leong Eng Choon of Nanyang Technological University, for his concern and encouragement over these years. Special thanks are due to Dr Muthusamy Karthikeyan, Mr Wong Tsz Ming and many other engineers from Surbana Consultants Pte Ltd, Singapore, TOA – JDN (PUT) Joint Venture, Singapore, for their support during my site visits, and for supplying materials for the laboratory testing. I appreciate the research scholarship and facilities provided by the National University of Singapore. The opportunity to work under “Ministry of National Development (MND) Research Fund for Built Environment” is acknowledged. The help rendered by laboratory officers in the Geotechnical laboratory of NUS is gratefully appreciated. I would also like to thank fellow research iii scholars Zhang Yi, Wu Jun, Sanjay, Tran, Faizul, Yannick, Eng and many others for the discussions, gossiping sessions, and warm friendship that has made my stay in NUS enjoyable. I thank Miss Chen Li for her company, care and encouragement. Last but not least, I would like to thank my parents for their love and support. April 11, 2014 iv Contents Introduction 1.1 Backgrounds . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Cement mixed clay as reclamation fill . . . . . . . . . . . . 1.3 Quality control of cement mixed dredged clay as reclamation fill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4 Research objectives . . . . . . . . . . . . . . . . . . . . . . 1.5 Organization of thesis . . . . . . . . . . . . . . . . . . . . . . . . . 11 . 13 Literature Review 2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2 Early strength (t < 48 hours) development of cement mixed soils with time . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3 Early strength development of concrete materials with time . 2.4 Influence of curing temperature on the strength development of cement mixed soils . . . . . . . . . . . . . . . . . . . . . . 2.4.1 Chitambira’s approach . . . . . . . . . . . . . . . . . 2.4.2 Long-term effect of curing temperature on the strength development of concrete/mortar . . . . . . . . . . . . 2.4.3 Effect of curing temperature on the setting behavior of concrete/mortar . . . . . . . . . . . . . . . . . . . 2.5 Early quality control of cement mixed soils . . . . . . . . . . 2.5.1 Flow value test . . . . . . . . . . . . . . . . . . . . . 2.5.2 Accelerated test of cement mixed soils . . . . . . . . 2.5.3 Slump test of concrete/mortar . . . . . . . . . . . . . 2.5.4 Accelerated test of concrete/mortar . . . . . . . . . . 2.6 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . v 1 14 14 16 26 31 32 44 45 51 55 56 59 60 64 Methodology 67 3.1 Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 3.1.1 Singapore Upper Marine Clay . . . . . . . . . . . . . 67 3.1.2 Portland Blast Furnace Cement . . . . . . . . . . . . 69 3.1.3 Seawater . . . . . . . . . . . . . . . . . . . . . . . . . 71 3.2 Experimental methods . . . . . . . . . . . . . . . . . . . . . 72 3.2.1 Preparation of cement mixed clay mixture . . . . . . 72 3.2.2 Preparation of test specimen . . . . . . . . . . . . . . 73 3.2.3 Curing . . . . . . . . . . . . . . . . . . . . . . . . . . 74 3.2.4 Unconfined compression test . . . . . . . . . . . . . . 75 3.2.5 Laboratory vane shear test . . . . . . . . . . . . . . . 75 3.2.6 Miniature T-bar penetrometer test . . . . . . . . . . 77 3.2.7 Isothermal calorimetry test . . . . . . . . . . . . . . . 79 3.2.8 Proposed accelerated test . . . . . . . . . . . . . . . 81 3.3 Experimental programme . . . . . . . . . . . . . . . . . . . . 82 3.3.1 Experimental investigation on early strength behavior of cement mixed Singapore Marine Clay . . . . . 82 3.3.2 Experimental investigation on effect of temperature on strength behavior of cement mixed Singapore Marine Clay . . . . . . . . . . . . . . . . . . . . . . . . . 82 3.3.3 Experimental validation of the proposed early quality control technique . . . . . . . . . . . . . . . . . . . . 83 3.4 Experimental Assessment of Flow Value Test . . . . . . . . . 85 3.4.1 Flow value test procedure . . . . . . . . . . . . . . . 85 3.4.2 Assessment programme of flow value test . . . . . . . 87 3.4.3 Relation between yield stress and flow value . . . . . 89 3.4.4 Correlation between flow value and later-age strengths 90 3.4.5 Strength behavior at t = . . . . . . . . . . . . . . . 92 3.4.6 Delayed Flow Value Test – An extended assessment of FVT . . . . . . . . . . . . . . . . . . . . . . . . . 95 3.4.7 Summary . . . . . . . . . . . . . . . . . . . . . . . . 100 Early Strength Behavior of Cement Mixed Singapore Upper Marine Clay 101 4.1 Transition behavior in early strength development . . . . . . 102 vi 4.2 4.3 4.4 4.5 4.6 Early strength development measured by T-bar . . . . . . Early strength development at different temperatures . . . 4.3.1 Repeatability of VST under elevated temperatures . Setting under different temperatures . . . . . . . . . . . . Estimating setting time under different temperatures . . . Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 113 118 119 128 131 Effect of Temperature on Strength Behavior of Cement Mixed Singapore Marine Clay 134 5.1 Long-term strength development under different temperatures135 5.2 Modelling strength developments under different temperatures140 5.2.1 Strength development with time . . . . . . . . . . . . 140 5.2.2 Modification to Chitambira’s model (2004) . . . . . . 143 5.2.3 Validation of the proposed model . . . . . . . . . . . 150 5.3 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 Proposal for a Novel Quality Control Technique 6.1 Proposed accelerated test . . . . . . . . . . . . . . . . . . 6.2 Experimental validation of the proposed accelerated test 6.2.1 Key variables on the accelerated strength qu (acc) 6.2.2 Correlations of qu (28day) – qu (acc) and qu (7day) qu (acc) . . . . . . . . . . . . . . . . . . . . . . . . 6.3 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . 163 . . 164 . . 169 . . 171 – . . 172 . . 176 Conclusions and Recommendations 177 7.1 Conclusions . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 7.2 Recommendations for future study . . . . . . . . . . . . . . 180 vii purpose to the author’s knowledge. It is to be noted that if different tools have to be adopted depending on the range of strength, which is dependent on the curing time, a relation or correlation must be developed between the measurements from different tools. As the property of the cement mixed clay changes with curing time, the relation or correlation between the measurements obtained from different tools may not be the same as those for natural soils. Therefore, it is useful to devise a testing tool that is suitable for measuring the entire range of strength the cement mixed clay is to develop in future studies. With such a tool, a holistic overview of the strength development of a cement mixed clay with time can be obtained. 182 Bibliography ACI (1978). SP-56: Acceleraed Strength Testing. American Concrete Institute. ACI (2008). Report on measurements of workability and rheology of fresh concrete. Technical report, American Concrete Institute. Ahnberg, H. (2006). Strength of stabilized soils - A laboratory study on clays and organic soils stabilized with different types of binder. Phd thesis. Al-Rawi, R. S. and K. Al-Murshidi (1978). Effects of w/c ratio and mix proportions in accelerated testing of concrete. Cement and Concrete Research (3), 343–350. ASTM (2003). C 684 standard test method for making, acclerated curing and testing concrete compression test specimens. ASTM (2005). D 4648 standard test method for laboratory miniature vane shear test for saturated fine-grained clayey soil. ASTM (2008). C 403 standard test method for time of setting of concrete mixture by penetration resistance. ASTM (2009). C 1679 standard practice for measuring hydration kinetics of hydraulic cementitious mixtures using isothermal calorimetry. Baghdadi, Z. A. (1982). Accelerated strength testing of soil-cement. Phd thesis. Ballim, Y. and P. C. Graham (2003). A maturity approach to the rate of heat evolution in concrete. Magazine of Concrete Research 55 (3), 249–256. 183 Barnett, S. J., M. N. Soutsos, S. G. Millard, and J. H. Bungey (2006). Strength development of mortars containing ground granulated blastfurnace slag: Effect of curing temperature and determination of apparent activation energies. Cement and Concrete Research 36 (3), 434–440. Bell, F. G. (1996). Lime stabilization of clay minerals and soils. Engineering Geology 42 (4), 223–237. Bennert, T. A., M. H. Maher, F. Jafari, and N. Gucunski (2000). Use of dredged sediments from newark harbor for geotechnical applications. ASTM Special Technical Publication 1374, 162–164. Bergado, D. T., L. R. Anderson, N. Miura, and A. S. Balasubramaniam (1996). Soft Ground Improvement in Lowlands and Other Environment. American Society of Civil Engineers. Bernhardt, C. J. (1956). Hardening of concrete at different temperatures. In RILEM Symposium on Winter Concreting, Session B2, Copenhagen, Denmark. Danish Institute for Building Research. Bickley, J. A. (1978). Accelerated concrete strength testing at the cn tower. ACI Special Publication 56, 29–38. Binns, T. (2003). Accelerated strength testing. In J. Newman and B. S. Choo (Eds.), Advanced Concrete Technology: Testing and Quality. Butterworth-Heinemann. Biswas, B. R. (1972). Study of Accelerated Curing and Other Factors Influencing Soil Stabilization. Phd thesis. BSI (1983). 1881-112: Testing concrete-methods of accelerated curing of test cubes. BSI (1990a). 1377-2: Methods of test for soils for civil engineering purposes - part 2: Classification tests. BSI (1990b). 1377-7: Methods of test for soils for civil engineering purposes - part 7: Shear strength tests (total stresses). 184 BSI (2005). En 196-3: Methods of testing cement. determination of setting times and soundness. Carino, N. J. (1982). Maturity functions for concrete. In RILEM International Conference on Concrete of Early Ages, Paris, France, pp. 123–128. Press de l’Ecole Nationale des Ponts et Chaussees. Carino, N. J. (2006). Prediction of potential concrete strength at later ages. In J. F. Lamond and J. H. Pielert (Eds.), Significance of tests and properties of concrete and concrete-making materials, Volume 169. ASTM International. Carino, N. J. and H. S. Lew (1983). Temperature effects on strengthmaturity relations of mortar. 80 (3), 177–182. Carino, N. J. and H. S. Lew (2001). The maturity method: from theory to application. In P. C. Chang (Ed.), Proceedings of the 2001 Structures Congress & Exposition, Washington DC, US, pp. 1–19. American Society of Civil Engineers. Chen, H. and C. Lee (2002). Runout analysis of slurry flows with bingham model. Journal of Geotechnical and Geoenvironmental Engineering 128 (12), 1032–1042. Chew, S. H., A. H. M. Kamruzzaman, and F. H. Lee (2004). Physicochemical and engineering behavior of cement treated clays. Journal of Geotechnical and Geoenvironmental Engineering 130, 696–706. Chin, F. K. (1971). Relation between strength and maturity of concrete. American Concrete Institute Journal 68 (3), 196. Chin, K. G. (2006). Constitutive behaviour of cement treated marine clay. Phd thesis. Chitambira, B. (2004). Accelerated ageing of cement stabilised/solidified contaminated soils with elevated temperatures. Phd thesis. Chung, S. F., M. F. Randolph, and J. A. Schneider (2006). Effect of penetration rate on penetrometer resistance in clay. Journal of Geotechnical and Geoenvironmental Engineering 132 (9), 1188–1196. 185 Clare, K. E. and A. E. Pollard (1954). The effect of curing temperature on the compressive strength of soil-cement mixtures. Geotechnique 4, 97–107. Clare, K. E. and P. T. Sherwood (1954). The effect of organic matter on the setting of soil-cement mixtures. Journal of Applied Chemistry (11), 625–630. Das Gupta, N. C. and C. T. Tam (1989). Controlled tropical curing method for accelerated concrete strengths. International Journal of Cement Composites and Lightweight Concrete 11 (1), 29–36. de Larrard, T., F. Benboudjema, J. B. Colliat, J. M. Torrenti, and F. Deleruyelle (2010). Concrete calcium leaching at variable temperature: Experimental data and numerical model inverse identification. Computational Materials Science 49 (1), 35–45. Dermatas, D., P. Dutko, J. Balorda-Barone, and D. H. Moon (2003). Evaluation of engineering properties of cement treated hudson river dredged sediments for reuse as fill materials. Journal of Marine Environmental Engineering (2), 101–123. Dodson, V. H. (1994). Time of setting. 169C, 77–87. Douglas, W. (2000). Creative solutions to dredged materials managementthe New Jersey experience. In Conference on Dredged Material Management: Options and Environmental considerations. Dubois, V., N. E. Abriak, R. Zentar, and G. Ballivy (2009). The use of marine sediments as a pavement base material. Waste Management 29 (2), 774–782. Enami, A., M. Yoshino, S. Hibino, M. Takahashi, and K. Akiya (1985). Insitu measurement of temperature in improved soil cement column and influence of curing temperature on unconfined compressive strength. In 10th Annual Meeting of JSSMFE, pp. 1737–1740. Japanese Society for Soil Mechanics and Foundation Engineering. 186 Fall, M. and S. Samb (2006). Influence of curing temperature on strength, deformation behaviour and pore structure of cemented paste backfill properties at early ages. Construction Building Materials (in press). doi:10.1026 10. Ferraris, C. F. and F. De Larrard (1998). Modified slump test to measure rheological parameters of fresh concrete. Cement, Concrete and Aggregates 20 (2), 241–247. Ferraris, C. F., F. De Larrard, and N. Martys (2001). Fresh concrete rheology: recent developments. Materials Science of Concrete VI , 215– 241. Ferrer, M. M. (1978). Quality control of concrete by means of short-termed tests at la angostura hydroelectric project, state of chiapas, mexico. ACI Special Publication 56, 51–74. Finnie, I. M. and M. F. Randolph (1994). Punch-through and liquefaction induced failure of shallow foundations on calcareous sediments. In Proceedings of International Conference on Behaviour of Offshore Structures, Volume 1, pp. 217–230. Pergamon Press Oxford, UK. Garcia, A., D. Castro-Fresno, and J. A. Polanco (2008). Maturity approach applied to concrete by means of vicat tests. ACI Materials Journal 105 (5), 445–450. Ge, Z., K. Wang, P. J. Sandberg, and J. M. Ruiz (2009). Characterization and performance prediction of cement-based materials using a simple isothermal calorimeter. Journal of Advanced Concrete Technology (3), 355–366. George, S. Z., D. A. Ponniah, and J. A. Little (1992). Effect of temperature on lime-soil stabilization. Construction and Building Materials (4), 247–252. Gerend, M. S. (1927). Steam cured cylinders give 28-day concrete strength in 48 hours. Engineering News Record 98 (7), 282–283. 187 Grubb, D. G., M. Chrysochoou, C. J. Smith, and N. E. Malasavage (2010). Stabilized dredged material. i: parametric study. Journal of Geotechnical and Geoenvironmental Engineering 136 (8), 1011–1024. Guo, C. J. (1989). Maturity of concrete: Method for predicting early-age strength. ACI Material Journal 86 (4), 341–353. Herzog, A. and J. K. Michel (1963). Reactions accompanying stabilization of clay with cement. High Research Record 36, 146–171. Horpibulsuk, S., N. Miura, and T. S. Nagarj (2003). Assessment of strength development in cement-admixed high water content clays with abram’s law as basis. Geotechnique 53, No.4, 439–444. Japanese Geotechnical Society (2000). Standard practice for making and curing stabilized soil specimens without compaction. in Japanese. Kada-Benameur, H., E. Wirquin, and B. Duthoit (2000). Determination of apparent activation energy of concrete by isothermal calorimetry. Cement and Concrete Research 30 (2), 301–305. Kamruzzaman, A. H. M. (2002). Physio-chemical & engineering behaviour of cement treated singapore marine clay. Phd thesis. Kaniraj, S. R. and V. G. Havanagi (1999). Compressive strength of cement stabilized fly ash-soil mixtures. Cement and Concrete Research 29 (5), 673–677. Kaniraj, S. R. and V. G. Havanagi (2001). Behavior of cement-stabilized fiber-reinforced fly ash-soil mixtures. Journal of Geotechnical and Geoenvironmental Engineering 127 (7), 574–584. Kawasaki, T., S. Saitoh, Y. Suzuki, and R. Babaski (1984). Deep mixing method using cement slurry as hardening agent. In S. Y. e. a. Lee (Ed.), Seminar on Soil Improvement and Construction Techniques in Soft Ground, Singapore, pp. 17–38. Japanese Society for Soil Mechanics and Foundation Engineering, National University of Singapore & Asian Institute of Technology. 188 Kawasaki, T. and Y. Suzuki (1981). On the deep mixing chemical mixing method using cement hardening agent. Technical report. Kim, J. K., Y. H. Moon, and S. H. Eo (1998). Compressive strength development of concrete with different curing time and temperature. Cement and Concrete Research 28 (12), 1761–1773. Kim, Y. T., J. Ahn, W. J. Han, and M. A. Gabr (2010). Experimental evaluation of strength characteristics of stabilized dredged soil. Journal of Materials in Civil Engineering 22 (5), 539–544. Kitazume, M. and K. Hayano (2007). Strength properties and variance of cement-treated ground using the pneumatic flow mixing method. Ground Improvement 11 (1), 21–26. Kitazume, M. and T. Satoh (2003). Development of a pneumatic flow mixing method and its application to central japan international airport construction. Ground Improvement (3), 139–148. Kitazume, M. and T. Satoh (2005). Quality control in central japan international airport construction. Ground Improvement (2), 59–66. Koh, G. Q. (2005). Singapore finds it hard to expand without sand. http://www.washingtonpost.com/wp-dyn/articles/ A52521-2005Apr14_2.html. last retrieved: 11/April/2013. Kulhawy, F. H., K. K. Phoon, and W. A. Prakoso (2000). Uncertainty in basic properties of geomaterials. In Proceedings of GeoEng2000: An international conference on geotechnical and geological engineering, Melbourne, Australia. Technomic Publishing Company. Lachemi, M., K. M. A. Hossain, C. Anagnostopoulos, and A. R. Sabouni (2007). Application of maturity method to slipforming operations: Performance validation. Cement and Concrete Composites 29 (4), 290–299. Larsson, S. (2005). State of practice reportexecution, monitoring and quality control. In International Conference on Deep Mixing Best Practice and Recent Advances, Stockholm, Sweden, pp. 732–785. 189 Lee, F. H., Y. Lee, S. H. Chew, and K. Y. Yong (2005). Strength and modulus of marine clay-cement mixes. Journal of Geotechnical and Geoenvironmental Engineering 131, 178–186. Lee, Y. (1999). A framework for the design of jet grout piles in Singapore marine clay. M.eng thesis. Lei, W. G. and L. J. Struble (1997). Microstructure and flow behavior of fresh cement paste. Journal of the American Ceramic Society 80 (8), 2021–2028. Liu, S. Y., D. W. Zhang, Z. B. Liu, and Y. F. Deng (2008). Assessment of unconfined compressive strength of cement stabilized marine clay. Marine Georesources and Geotechnology 26 (1), 19–35. Locat, J. B. and M. Marc-Andre, B.and Choquette (1990). Laboratory investigations on the lime stabilization of sensitive clays: shear strength development. Canadian Geotechnical Journal 27 (3), 294–304. Low, H. E. and M. F. Randolph (2010). Strength measurement for nearseabed surface soft soil using manually operated miniature full-flow penetrometer. Journal of Geotechnical and Geoenvironmental Engineering 136 (11), 1565–1573. Lui, P. C. and T. S. Tan (2001). Building integrated large-scale urban infrastructures: Singapore’s experience. Journal of Urban Technology (1), 49–68. Madhyannapu, R., A. Puppala, S. Nazarian, and D. Yuan (2010). Quality assessment and quality control of deep soil mixing construction for stabilizing expansive subsoils. Journal of Geotechnical and Geoenvironmental Engineering 136 (1), 119–128. Malhotra, V. M. and N. G. Zoldners (1969). Some field experience in the use of an accelerated method of estimating 28-day strength of concrete. American Concrete Institute Journal 66 (11), 894–897. 190 Marzano, I. P., A. Al-Tabbaa, and M. Grisolia (2008). Influence of curing temperature on the strength of cement-stabilised artificial clays. In M. Karstunen and M. Leoni (Eds.), Geotechnics of soft soils - focus on ground improvement, Glasgow, UK, pp. 257–262. Taylor & Francis. Meyer, D. (1997). A statistical comparison of accelerated concrete testing methods. Journal of Applied Mathematics and Decision Sciences (2), 89–100. Mindess, S., J. F. Young, and D. Darwin (2002). Concrete (2nd ed.). Prentice-Hall. Ministry of National Development (2013). A high quality living environment for all Singaporeans - Land use plan to support Singapore’s future population. Mitchell, J. K., T. S. Veng, and C. L. Monismith (1972). Behavior of stabilized soils under repeated loading. report 5. performance evaluation of cement-stabilized soil layers and its relationship to pavement design. Technical report, University of California, Berkeley. Miura, N., S. Horpibulsuk, and T. S. Nagaraj (2001). Engineering behavior of cement stabilized clay at high water content. Soils and Foundations 41 (5), 33–45. Mooney, M. A. and N. M. Toohey (2010). Accelerated curing and strengthmodulus correlation for lime-stabilized soils. Technical report, Colorado Department of Transportation, DTD Applied Research and Innovation Branch. Morohoshi, K., K. Yoshinaga, M. Miyata, I. Sasaki, H. Saitoh, M. Tokoro, N. Fukuda, T. Fujii, K. Yamada, and M. Ishikawa (2010). Design and long-term monitoring of tokyo international airport extension project constructed on super-soft ground. Geotechnical and Geological Engineering 28 (3), 223–232. Murata, J. (1984). Flow and deformation of fresh concrete. Materiaux et Constructions 17 (2), 117–129. 191 Nagaraj, T. S., P. Yarigar, N. Miura, and A. Yamadera (1996). Prediction strength development cement admixutre based on water content. In R. Yonekura, M. Terashi, and M. Shibazaki (Eds.), 2nd International Conference on Ground Improvement Geosystems, Volume 1, pp. 431– 436. Naik, T. R. (1979). Utilization of accelerated strength testing methods. Cement and Concrete Research (1), 7–17. Nasser, K. W. (1978). A new method and apparatus for accelerated strength testing of concrete. American Concrete Institute Journal 56, 249–258. Nasser, K. W. and V. M. Malhotra (1990). Accelerated testing of concrete: Evaluation of the k-5 method. ACI Materials Journal 87 (6). Nelson, E. B. (1990). Well cementing. Houston, Texas, US: Schlumberger Educational Services. Neville, A. M. (1996). Properties of Concrete. Pearson Prentice Hall. Neville, A. M. (2006). Concrete: Neville’s insights and issues. Thomas Telford Services Ltd. Noble, D. F. and R. W. Plaster (1970). Reactions in portland cement-clay mixtures. Technical report, Virginia Highway Research Council. Nurse, R. W. (1949). Steam curing of concrete. Magazine of Concrete Research (2), 79–88. Ozkul, M. H. (2001). Efficiency of accelerated curing in concrete. Cement and Concrete Research 31 (9), 1351–1357. Oztekin, E. (1987). Accelerated strength testing of portland-pozzolan cement concretes by the warm water method. ACI Materials Journal 84 (1), 51–54. Pashias, N., D. V. Boger, J. Summers, and D. J. Glenister (1996). A fifty cent rheometer for yield stress measurement. Journal of Rheology 40 (6), 1179–1189. 192 Patch, O. G. (1933). An 8-hour accelerated strength test for field concrete control. American Concrete Institute Journal 29. Pinto, R. C. (1997). The effect of cuirng temperatures on the development of mechanical properties of fresh and hardened high-strength silica fume mixtures - a maturity approach. Phd thesis. Pinto, R. C. and K. C. Hover (1999). Application of maturity approach to setting times. ACI Material Journal 96 (6), 686 – 691. Pinto, R. C. and A. K. Schindler (2010). Unified modeling of setting and strength development. Cement and Concrete Research 40 (1), 58–65. Plowman, J. M. (1956). Maturity and the strength of concrete. Magazine of Concrete Research (22), 13–22. Porbaha, A. (2002). State of the art in quality assessment of deep mixing technology. Ground Improvement 6, 95–120. Porbaha, A., H. Hanzawa, and H. Shima (1999). Technology of airtransported stabilized dredged fill. part i: Pilot study. Ground Improvement 3, 49–58. Porbaha, A., S. Shibuya, and T. Kishida (2000). State of the art in deep mixing technology. part iii: Geomaterial characterization. Ground Improvement (3), 91–110. Princigallo, A., P. Lura, K. van Breugel, and G. Levita (2003). Early development of properties in a cement paste: A numerical and experimental study. Cement and Concrete Research 33 (7), 1013–1020. Rahman, M. M., M. Taiyab, A. Siddique, and M. K. Uddin (2008). A shortcut method for predicting strength of cement treated soft bangladesh clays and the alteration of other engineering parameters. Geotechnical Engineering 39 (3), 159–167. Randolph, M. and K. Andersen (2006). Numerical analysis of t-bar penetration in soft clay. International Journal of Geomechanics (6), 411–420. 193 Randolph, M. F. and G. T. Houlsby (1984). Limiting pressure on a circular pile loaded laterally in cohesive soil. Geotechnique 34 (4), 613–623. Rekik, B. and M. Boutouil (2009). Geotechnical properties of dredged marine sediments treated at high water/cement ratio. Geo-Marine Letters 29 (3), 171–179. Resheidat, M. R. and M. S. Ghanma (1997). Accelerated strength and testing of concrete using blended cement. Advanced Cement Based Materials (2), 49–56. Saak, A. W., H. M. Jennings, and S. P. Shah (2004). A generalized approach for the determination of yield stress by slump and slump flow. Cement and Concrete Research 34 (3), 363–371. Sakamoto, A. (1998). Cement and soft mud mixing technique using compressed air-mixture pipeline: Efficient solidification at a disposal site. Terra et Aqua (73), 11–22. Sant, G., C. F. Ferraris, and J. Weiss (2008). Rheological properties of cement pastes: A discussion of structure formation and mechanical property development. Cement and Concrete Research 38 (11), 1286–1296. Saul, A. G. A. (1951). Principles underlying the steam curing of concrete at atmospheric pressure. Magazine of Concrete Research (6), 127–140. Schowalter, W. R. and G. Christensen (1998). Toward a rationalization of the slump test for fresh concrete: Comparisons of calculations and experiments. Journal of Rheology 42 (4), 865–889. Schwartz, M. (2005). Encyclopedia of coastal science. Seng, S. and H. Tanaka (2011). Properties of cement treated soils during initial curing stages. Soils and foundations 51 (5), 775–784. Shaughnessy, R. and P. E. Clark (1988). The rheological behavior of fresh cement pastes. Cement and Concrete Research 18 (3), 327–341. 194 Siham, K., B. Fabrice, A. N. Edine, and D. Patrick (2008). Marine dredged sediments as new materials resource for road construction. Waste Management 28 (5), 919–928. Singapore Department of Statistics, (2010). Yearbook of statistics singapore. Technical report. Soroka, I. (1994). Concrete in Hot Environments. Taylor & Francis. Stewart, D. P. and M. F. Randolph (1994). T-bar penetration testing in soft clay. Journal of Geotechnical Engineering 120 (12), 2230–2235. Struble, L. J. and W. G. Lei (1995). Rheological changes associated with setting of cement paste. Advanced Cement Based Materials (6), 224– 230. Tan, T. S., T. L. Goh, and K. Y. Yong (2002). Properties of singapore marine clays improved by cement mixing. ASTM Geotechnical Testing Journal 25 (4), 422–433. Tank, R. C. and N. J. Carino (1991). Rate constant functions for strength development of concrete. ACI Materials Journal 88 (1), 74–83. Terashi, M. and M. Kitazume (2011). Qa/qc for deep-mixed ground: current practice and future research needs. Proceedings of the ICE-Ground Improvement 164 (3), 161–177. TOA Corporation, (2007). Index property test results. Technical report. TOA Corporation, (2009). Test report: unconfined compressive test for sdf construction. Technical report. Tokyay, M. (1999). Strength prediction of fly ash concretes by accelerated testing. Cement and Concrete Research 29 (11), 1737–1741. Turcry, P., A. Loukili, L. Barcelo, and J. M. Casabonne (2002). Can the maturity concept be used to separate the autogenous shrinkage and thermal deformation of a cement paste at early age ? Cement and Concrete Research 32 (9), 1443–1450. 195 Van Impe, W. F. and R. D. Verastegui Flores (2006). Deep mixing in underwater conditions: A laboratory and field investigation. Ground Improvement 10 (1), 15–22. Wade, S., J. Nixon, A. Schindler, and R. Barnes (2010). Effect of temperature on the setting behavior of concrete. Journal of Materials in Civil Engineering 22 (3), 214–222. Wang, K., Z. Ge, J. Grove, J. M. Ruiz, and R. O. Rasmussen (2006). Developing a simple and rapid test for monitoring the heat evolution of concrete mixtures for both laboratory and field applications. Technical report, Center for Transportation Research and Education, Iowa State University. Watabe, Y. and T. Noguchi (2011). New challenge in d-runway construction of tokyo haneda airport. In Proceedings of Indian Geotechnical Conference IGC-11, Kochi, India, pp. 41–44. Watabe, Y., T. Tsuchida, F. T., and H. Yuasa (2000). Mechanical characteristics of a cement treated dredged soil utilized for waste reclamation landfill. In A. Nakasa and T. Tsuchida (Eds.), Coastal geotechnical engineering in practice: proceedings of the international symposium, ISYokohama 2000, Yokohama, Japan, pp. 739–745. Taylor & Francis. Weakley, R. (2009). Evaluation of semi-adiabatic calorimetry to quantify concrete setting. M.eng thesis. Weiss, W. J. (2003). Experimental determination of the’time-zero’ t0 (maturity zero m0 ). In A. Bentur (Ed.), Early Age Cracking In Cementitious Systems - Report of RILEM Technical Committee 181-EAS, pp. 195 – 206. RILEM Publications SARL. World Bank, (2010). Population density (people per sq. km of land area). http://data.worldbank.org/indicator/EN.POP.DNST. last retrieved: 09/April/2013. Wu, X., D. M. Roy, and C. A. Langton (1983). Early stage hydration of slag-cement. Cement and Concrete Research 13 (2), 277–286. 196 Xiao, H. (2009). Yielding and failure of cement treated soil. Phd thesis. Yun, J. M., Y. S. Song, J. H. Lee, and T. H. Kim (2006). Strength characteristics of the cement-stabilized surface layer in dredged and reclaimed marine clay, korea. Marine Georesources and Geotechnology 24 (1), 29– 45. Zhang, R. J., A. M. Santoso, T. S. Tan, and K. K. Phoon (2013). Strength of high water content marine clay stabilized by low amount of cement. Journal of Geotechnical and Geoenvironmental Engineering in press. 197 [...]... strength behaviors of cement mixed soils are reviewed in Section 2.2 Due to the fact that there have been only limited studies on the early strength of cement mixed soils, the early strength behavior of concrete/mortar is reviewed in Section 2.3 as well and comparisons are drawn with cement mixed soils Second, the effect of curing temperature on the strength development of cement mixed soils is reviewed... reactions in the cement treated clay There is a lack of understanding of how the strength development is influenced by the curing temperature The research objectives of this study are therefore as follows: 11 i To acquire an in-depth understanding on the early strength behavior of cement mixed Singapore marine clay at high water content ii To study the effect of curing temperature on the strength development. .. assessment of Flow Value Test (FVT), from which the irrelevance of FVT in this research is concluded In Chapter 4, the early strength behavior of cement mixed clay is discussed based on the experimental results from the investigation of the early strength development In the same chapter, the effect of temperature on the early strength behavior is also discussed The influence of temperature on long-term strength. .. between the QC sample and the actual quality of the cement mixed clay fill is dependent on the curing temperature in the field Unfortunately, there has not been any in-depth understanding of the curing temperature effect on the strength development of cement mixed clays A detailed review of the curing temperature effect on the strength development of cement mixed soils is presented in Chapter 2 9 (a) Temperature...List of Figures 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 2.1 2.2 2.3 2.4 2.4 Extent of reclaimed land in Singapore (based on Ministry of National Development, 2013 and Schwartz, 2005) Land area of Singapore from 1960s to 2010s Operation process of using cement mixed dredged clay as fill in the reclamation project in Singapore Operations involved in the use of cement mixed dredged clay. .. research on the strength development at very early curing ages (within 2 days upon the completion of mixing) for cement mixed clays, especially for slurry dredged clay mixed with high water content and low cement dosage ii As has been discussed, the effectiveness of the current early QC measure is questionable and provides limited understandings on the mixture’s early strength behavior iii As Singapore is... various aspects of the strength development of the cement mixed soil are fundamentally similar to that of concrete/mortar as both the materials are cement based and their strength developments depend on the cement hydration Therefore, the limited studies on the cement mixed soils may be complemented by the established understandings of concrete/mortar on relevant topics Besides, the effect of the mix proportions... effect of curing temperature on the strength development of concrete/mortar is discussed and compared with that of cement mixed soils as understandings on this topic are better established for concrete/mortar than for cement mixed soils Last, a detailed review on the early QC of cement mixed soils and concrete/mortar is presented in Section 2.5 One shall note that in this chapter, the relevant topics of. .. cement dosage is excessive Removal of the defective material is technically impractical and economically unsound as it may involve huge area of treated land, which contains defective yet hardened materials Another important aspect of QC of the cement mixed dredged clay fill in Singapore is the effect of curing temperature on the strength development As a tropical country, the ambient temperature of Singapore. .. 10 1.4 Research objectives Cement mixed clays have been widely used for soil improvement in various kinds of geotechnical applications Using cement mixed dredged clay as fill, in particular as material for the containment bund, is a relatively new variation from conventional clay cement mixtures, as the base clay is usually high in initial water content (often ≥ 1.5 times of its liquid limit) and the . EARLY STRENGTH DEVELOPMENT OF CEMENT MIXED SINGAPORE MARINE CLAY LU YITAN NATIONAL UNIVERSITY OF SINGAPORE 2014 EARLY STRENGTH DEVELOPMENT OF CEMENT MIXED SINGAPORE MARINE CLAY LU YITAN (B.Eng early strength behav- ior of cement mixed Singapore Marine Clay . . . . . 82 3.3.2 Experimental investigation on effect of temperature on strength behavior of cement mixed Singapore Ma- rine Clay. 131 5 Effect of Temperature on Strength Behavior of Cement Mixed Singapore Marine Clay 134 5.1 Long-term strength development under different temperatures135 5.2 Modelling strength developments