NC2000 system operation manual vol1

NC2000 System Operation Manual V2.0 Volume I System Installation NARI Group Corp Nanjing Automation Research Institute April.2006 Copyright Announcement Warning: This Computer Program is protected by copyright law and international treaties Unauthorized reproduction or distribution of this program, or any portion of it, may result in severe civil and criminal penalties, and will be prosecuted to the maximum extent possible under the law 、 is registered trade mark of NARI Group Corp @ 2004 Nanjing Automation Research Institute All rights reserved Preface NC2000 is new generation computer monitoring & control software developed for electric power system, and it is based on the experience accumulated by Nari access system used in many hydropower plants This system use Client/Server structure, support different hardware, operating system and relative DB system Object-oriented pattern is used in design and develop process It will be more convenient and visual for users This manual mainly introduces the installation, operation and maintenance of NC2000 system It includes four parts: Volume I, Introduction of installation process for NC2000 system, including installation for operation system and configuration for NC2000 Volume II, User operation manual, which detailedly introduce how to use NC2000 system Volume III, Introduction of configuration tools, which introduce how to use system configuration software Volume IV, system maintenance manual, which introduce all the parts need to be maintained, means and steps for maintenance We hope this manual can help you master our NC2000 system fluently, and keep the system safe, reliable and stable Guideline [Target] This manual is Volume I of NC2000 system, it mainly introduce the installation process [User] All the engineers of software installation, configuration and maintenance [Structure] This manual includes two parts: Part I: Installation of operation system It introduces the installation process and steps of relative operation system for NC2000 Nowadays, NC2000 system has successfully run on Windows2000, Red Hat Linux and Sun Solaris 9、10 Part II: Installation of NC2000 system It includes “Installation and Configuration of NC2000”, ” Installation and Configuration of NARI Oncall”, “Installation and Configuration of Remote Diagnose Service” It introduces the NC2000 installation process on relative operation system, Project setup and configuration, installation and configuration of NARI Oncall and Remote Diagnose Service (RDS) [Rules] This manual obeys the following rules: All the titles are in bold face If the title follows by “[Condition]”, It means the contents below this title is required under certain conditions [Notice] User should notice relative issues [Warning] User must notice these issues; otherwise it will result in severe faults Contents CHAPTER I OVERVIEW CHAPTER INSTALLATION OF OPERATION SYSTEM 2.1 Installation of Windows 2000 .2 2.1.1 Installation of Windows 2000 2.1.2 Windows 2000 Update 11 2.2 Installation of Red Hat Linux 9.0 .15 2.2.1 Installation of Red Hat Linux 9.0 15 2.2.2 System Configuration 29 2.2.3 Installation of Java 1.5.0 on Red Hat Linux .31 2.3 Installation of Sun Solaris 31 2.3.1 Installation of Sun Solaris 31 2.3.2 Patch update and configuration for Sun Solaris 34 2.3.3 Installation of Java 1.5.0 on Solaris Unix 37 2.4 Installation of Sun Solaris 10 .38 2.4.1 Preparation before installation 38 2.4.2 Installation steps of Sun Solaris Unix 10 .38 CHAPTER INSTALLATION OF NC2000 MONITORING SYSTEM .41 3.1 Installation of NC2000 on Windows 2000 41 3.1.1 Installation process 41 3.1.2 System configuration .41 3.2 Installation of NC2000 on Red Hat Linux 9.0 42 3.2.1 Installation process 42 3.2.2 NARI Auto-start configuration .42 3.3 Installation of NC2000 on Sun Solaris Unix 9.0 .45 3.3.1 Installation process 45 3.3.2 System configuration .45 3.4 Installation of NC2000 Web system（C/S） 46 3.4.1 Foundation of NC2000 Web server（C/S） 46 3.4.2 Configuration and Application of NC2000 Web Client（C/S） .53 3.4.3 Installation of NC2000 Web Server（B/S V1.0） 59 CHAPTER PROJECTS CONFIGURATION FOR NC2000 SYSTEM 63 4.1 Projects configuration for NC2000 system 63 4.1.1“NC2000 Configuration” 63 4.1.2 Configuration steps for NC2000 project 64 4.1.3 Example for NC2000 configuration .64 4.2 Directory tree of NC2000 configuration file 65 4.2.1 System file directory: data .65 4.2.2 Project directory: projects.strategy .66 CHAPTER INSTALLATION OF NARI ONCALL SYSTEM 67 5.1 Hardware configuration 67 5.1.1 Computer hardware requirement 67 5.1.2 Telephone pronunciation card .68 5.1.3 GSM Modem 68 5.2 Installation of telephone card driver for NARI Oncall system 68 5.2.1 Driver installation 68 5.2.2 audio card configuration 70 CHAPTER INSTALLATION AND CONFIGURATION OF RDS 72 6.1 Modem installation 72 6.2 Remote server installation 72 6.3 system configuration 74 6.4 Network configuration 77 6.5 Dial server installation 81 6.6 Start local Telnet service 87 Chapter I Overview NC2000 is automatic monitoring and control software for hydro-power plants; it is developed by NARI Automation Research Institute, and can run on Windows, Linux, Unix, etc This manual mainly introduces the installation and configuration process of relative operation system and software system It also introduces how to install and configure NC2000 on these platforms Operation system installation mainly introduces the installation process of Windows 2000, Red Hat Linux 9.0 and Sun Solaris Unix 9.0 It also introduces the installation and configuration process of relative software, for example, JAVA, Sun Cluster NC2000 Installation introduces the installation and configuration process of NC2000 on different operation system (Windows 2000, Red Hat Linux 9.0 and Sun Solaris Unix 9.0) Project Configuration for NC2000 describes how to setup a new project, and briefly introduces the function of relative configuration files and how to use them NARI Oncall system is one set of Real-time alarm and query system through by telephone, message or Speech This Chapter introduces its installation and configuration process Using RDS system, engineers can connect and maintain our monitoring system thorough remote dial network Chapter Installation of operation system 2.1 Installation of Windows 2000 2.1.1 Installation of Windows 2000 NC2000 system can run on 32-bit PC, Micro Workstation and Server which has installed Windows 2000 Minimum requirements:  850MHz Intel Pentium III or coordinate  512MB RAM  10GB available disk space  16 bit sound board and speaker  65,000 color video card ， resolution is 800x600 (mini font) or 1024x768（big font） Recommendatory:  3.2GHz Intel Pentium IV or coordinate  1G RAM  80GB available disk space  16 bit sound board and speaker  32-bit colorful video card， resolution is 1024x768（big font） The installation steps on PC are as follows: Insert Win2000 floppy disk, following this screen: Fig 2-1 Select 1, Start Window 2000 professional Installation: Fig 2- Installation will push the graph from 6-4 to 6-5。 不要点找“取消” Fig.6-4 点找找 Fig.6-5 Click “OK” then Fig.6-6 will appear Select “Yes，I want to reboot computer immediately”，then click “Close”。 先 找找找 点找找 Fig.6-6 Installation is finished 6.3 system configuration 74 Select “start/ settings/ control panel”： 找到“控制面板” Fig.6-7 Select “Telephone and modem item” 找找找 Fig.6-8 75 Select “Modem” item 点找找 找找找找 的 Modem Fig.6-9 Select relative Modem，click “Properties”。 找找音量到最高 找找速度到最高 Fig.6-10 Set “Speaker volume” to highest Set “Maximum COM speed” to fastest。 76 Click “OK”, then return to fig 6-9, click “OK” Close “control panel” 6.4 Network configuration Right click “My Network Places”, click “properties” Fig.6-11 “Network and Dial-up Connection” window（Fig.6-12）will appear。Double click “Local area connection” then Fig.6-13 will appear。 Fig.6-12 77 Fig.6-13 Click “Properties” in fig.6-13，fig.6-14 will appear。 Select “Internet protocol（TCP/IP）”，then click “Properties”。Fig.6-15 will appear。 78 Fig.6-14 79 Fig.6-15 click “advanced (V)…”，fig 6-16 will appear。 Select “IP settings” item, view IP address in “IP address(R)” list If it has “192.9.22.1”，go to step 6; if no, click “Add (A)…” Fig 6-17 will appear。 Fig.6-16 Fig.6-17 80 Enter “192.9.22.1” in “IP address (I):”, Enter “255.255.255.0” in “Subnet mask (S):” Then click “add (A)” fig 6-18 will appear。 Now “192.9.22.1” will appear in IP address list。 click “OK”, then return to fig 6-15 Click “ok”, then return to fig.6-14 Click “ok”, then return to fig.6-13 10 Click “close” 6.5 Dial server installation View if it has “incoming connection” in fig.6-12，if yes, no need to configure; if no, configure it as follows: double click “Make New connection”，fig 6-18 will appear。 Fig.6-18 81 Click “Next”，fig 6-19 will appear Fig.6-19 select “Accept incoming connections (A)”, then click “Next” 82 Fig.6-20 Select your modem in “Connection device（C）:” Click “Next” Select “Do not allow virtual private connections（D）”，then click “Next”。 An information box will pop up as fig.6-22 click “OK” Fig.6-21 83 Fig.6-22 View if it has user “nari” If no, click “Add (A)”, go to step 8; if yes, select user “Nari”, and click “properties” Make sure the password of user “nari” is “nari” Add new user Fig.6-23 Enter “nari” in all the txt box, then click “OK” Select user “nari”, then click “Next” 84 Fig.6-24 10 Select “Internet protocol (TCP/IP)”, then click “properties” Fig.6-25 85 Fig.6-26 11 Enter the IP address and select relative item following fig.6-28 then click “OK” to return to fig.6-25 click “Next ” to go to fig 6-27 86 12 Click “finish”。 Fig.6-27 13 Completing the Network Connection Wizard。 6.6 Start local Telnet service Start control panel\administrative tools\Telnet server administration Enter the following number or letter in popped up windows （ comments after “//”）: //stop services // display or modify regedit // NTLM y // Modify this value // Cancel NTLM validation y // confirm modification // exit // Start service // exit 87 Start [Control panel\administrative tools\services] Find “Telenet”，and double click it In “properties” window ，change “start type” to “auto”, then click “apply” and ”OK” 【Notice】Because of the plug and play property of Windows 2000, Modem driver will not be loaded when computer start if Modem has no power or not connected to computer (It means Modem can not be detected when windows start) When it happens, please power on the Modem, and make sure Modem and computer is connected, then reboot computer to detect Modem again Because in most plants, telephone line is used with other run telephone, usually you not need to start Modem If you want to start RDS, make sure Modem is connected to computer and power on before computer reboot So windows 2000 can detect Modem and load its driver If Modem is independent, you not need to close it 88 ... [Structure] This manual includes two parts: Part I: Installation of operation system It introduces the installation process and steps of relative operation system for NC2000 Nowadays, NC2000 system has... system, including installation for operation system and configuration for NC2000 Volume II, User operation manual, which detailedly introduce how to use NC2000 system Volume III, Introduction of... this manual can help you master our NC2000 system fluently, and keep the system safe, reliable and stable Guideline [Target] This manual is Volume I of NC2000 system, it mainly introduce the installation