Kết nối WinCC với PLC s7 1200 và 1500

http://support.automation.siemens.com/WW/view/en/101908495 Configuration Example  10/2014 WinCC Connection to S7-1200 and S7-1500 WinCC V7.3 Warranty and Liability WinCC S7-1200/ S7-1500 Entry ID: 101908495, V1.0, 10/2014 2 ã Siemens AG Copyright- 2014 All rights reserved Warranty and Liability Note The Application Examples are not binding and do not claim to be complete regarding the circuits shown, equipping and any eventuality. The Application Examples do not represent customer-specific solutions. They are only intended to provide support for typical applications. You are responsible for ensuring that the described products are used correctly. These Application Examples do not relieve you of the responsibility to use sound practices in application, installation, operation and maintenance. When using these Application Examples, you recognize that we cannot be made liable for any damage/claims beyond the liability clause described. We reserve the right to make changes to these Application Examples at any time and without prior notice. If there are any deviations between the recommendations provided in these Application Examples and other Siemens publications – e.g. Catalogs – the contents of the other documents have priority. We do not accept any liability for the information contained in this document. Any claims against us – based on whatever legal reason – resulting from the use of the examples, information, programs, engineering and performance data etc., described in this Application Example shall be excluded. Such an exclusion shall not apply in the case of mandatory liability, e.g. under the German Product Liability Act (“Produkthaftungsgesetz”), in case of intent, gross negligence, or injury of life, body or health, guarantee for the quality of a product, fraudulent concealment of a deficiency or breach of a condition which goes to the root of the contract (“wesentliche Vertragspflichten”). The damages for a breach of a substantial contractual obligation are, however, limited to the foreseeable damage, typical for the type of contract, except in the event of intent or gross negligence or injury to life, body or health. The above provisions do not imply a change of the burden of proof to your detriment. Any form of duplication or distribution of these Application Examples or excerpts hereof is prohibited without the expressed consent of Siemens Industry Sector. Security informa- tion Siemens provides products and solutions with industrial security functions that support the secure operation of plants, solutions, machines, equipment and/or networks. They are important components in a holistic industrial security concept. With this in mind, Siemens’ products and solutions undergo continuous development. Siemens recommends strongly that you regularly check for product updates. For the secure operation of Siemens products and solutions, it is necessary to take suitable preventive action (e.g., cell protection concept) and integrate each component into a holistic, state-of-the-art industrial security concept. Third-party products that may be in use should also be considered. For more information about industrial security, visit http://www.siemens.com/industrialsecurity. To stay informed about product updates as they occur, sign up for a product- specific newsletter. For more information, visit http://support.automation.siemens.com. Table of Contents WinCC S7-1200/ S7-1500 Entry ID: 101908495, V1.0, 10/2014 3 ã Siemens AG Copyright- 2014 All rights reserved Table of Contents Warranty and Liability 2 1 Task 4 2 Solution 5 2.1 Overview 5 2.2 Hardware and software components 7 2.2.1 Validity 7 2.2.2 Components used 7 3 Configuration and Settings 9 3.1 Loading AS symbols from an existing S7-1500 program 9 3.2 Loading AS messages from an existing S7-1500 program 15 4 References 18 5 History 18 1 Task WinCC S7-1200/ S7-1500 Entry ID: 101908495, V1.0, 10/2014 4 ã Siemens AG Copyright- 2014 All rights reserved 1 Task Figure 1-1 S7-1500 S7-1200 WinCC V7.3 Encrypted process connection Process connection Introduction The task is to provide process tags and AS messages of S7-1200 and S7-1500 in WinCC V7.3. It is to be possible to establish a protected HMI connection to S7-1500. 2 Solution 2.1 Overview WinCC S7-1200/ S7-1500 Entry ID: 101908495, V1.0, 10/2014 5 ã Siemens AG Copyright- 2014 All rights reserved 2 Solution 2.1 Overview Setup The following scheme shows the most important components of the solution: Figure 2-1 S7-1500 S7-1200 PROFINET IE WinCC V7.3 SIMATIC S-1200, S7-1500 Channel Description WinCC V7.3 provides the communication channel "SIMATIC S7-1200, S7-1500 Channel" for communication with S7-1200 and S7-1500 CPUs. Communication to S7-1200 and S7-1500 can be realized with absolute addressing and since WinCC V7.3 also with symbolic addressing. Between WinCC V7.3 and S7-1500, a protected communication connection can be established. Characteristic features · Access to the symbolic addresses and CPU alarming is effected via the online connection to the CPU only. · Offline configuration is only possible for the absolute addresses. Note Currently, no raw data tags can be used via the "SIMATIC S7-1200, S7-1500 Channel". 2 Solution 2.1 Overview WinCC S7-1200/ S7-1500 Entry ID: 101908495, V1.0, 10/2014 6 ã Siemens AG Copyright- 2014 All rights reserved Features of the communication to S7-1200 and S7-1500 · Cyclic reading of tags · Chronological reporting (program alarm) · Loading of AS messages (S7-1500) · Password protection · Time synchronization · Use of S7-1200/S7-1500 tags in WinCC – Export/Import function 1) Export of the tags from TIA Portal (only absolute addressing) 2) Import to WinCC via the WinCC Configuration Studio · Loading of AS symbols Delimitation This application does not contain a description of: · Configuration of S7-1500 in TIA Portal · Installation of SIMATIC TIA Portal and WinCC V7.3 Basic knowledge of these topics is assumed. Assumed knowledge Basic knowledge of WinCC V7.3 and SIMATIC TIA Portal is assumed. 2 Solution 2.2 Hardware and software components WinCC S7-1200/ S7-1500 Entry ID: 101908495, V1.0, 10/2014 7 ã Siemens AG Copyright- 2014 All rights reserved 2.2 Hardware and software components 2.2.1 Validity This application is valid for · STEP 7 from V13 · WinCC V7.3 · S7-1200 (from firmware V2.2) · S7-1500 2.2.2 Components used The application was created with the following components: Hardware components Table 2-1 Component No. Article number Note S7-1516-3 PN/DP 1 6AG1516-3AN00-7AB0 Alternatively, any other S7- 1500 or S7-1200 can be used. Development system 1 PC for configuration of controller and WinCC. The hardware requirements for STEP 7 and WinCC apply. Software components Table 2-2 Component No. Article number Note WinCC V7.3 1 6AV63.1 7-3 TIA Portal STEP 7 V13 Professional 1 6ES7822-1 03 Alternatively, TIA Portal STEP 7 V13 Basic can be used for S7-1200. NOTE Use the SIMATIC NET V12 installation being enclosed to WinCC V7.3 if no STEP 7 or TIA Portal is installed on the computer. (With it the communication drivers are installed.) Sample files and projects The following list includes all files and projects that are used in this example. 2 Solution 2.2 Hardware and software components WinCC S7-1200/ S7-1500 Entry ID: 101908495, V1.0, 10/2014 8 ã Siemens AG Copyright- 2014 All rights reserved Table 2-3 Component Note color_filling_station.zip Getting Started S7-1500 101908495_WinCC_S71200_S71500_Chanel_de.pdf This document. 3 Configuration and Settings 3.1 Loading AS symbols from an existing S7-1500 program WinCC S7-1200/ S7-1500 Entry ID: 101908495, V1.0, 10/2014 9 ã Siemens AG Copyright- 2014 All rights reserved 3 Configuration and Settings 3.1 Loading AS symbols from an existing S7-1500 program This section describes the configuration of tags in WinCC with optimized block access to the address range in the S7-1500 automation system. Table 3-1 Process Action 1 Opening a WinCC project Create a new WinCC project or open an existing one. 2 Creating an S7-1200 / S7-1500 channel Open Tag Management. Enter the IP address, access point, and product family. 3 Add a SIMATIC S7-1200, S7-1500 Channel. 3 Configuration and Settings 3.1 Loading AS symbols from an existing S7-1500 program WinCC S7-1200/ S7-1500 Entry ID: 101908495, V1.0, 10/2014 10 ã Siemens AG Copyright- 2014 All rights reserved Process Action 4 Right-click and add a "New Connection". 5 Right-click and open the "Connection parameters". Enter the new IP address of your S7-1500 or S7-1200 here. [...]... again with the "Read from AS" command WinCC S7- 1200/ S7- 1500 Entry ID: 101908495, V1.0, 10/2014 14 3 Configuration and Settings 3.2 Loading AS messages from an existing S7- 1500 program 3.2 Loading AS messages from an existing S7- 1500 program Table 3-2 Process Open the "Alarm logging" editor ã Siemens AG Copyright- 2014 All rights reserved 1 Action WinCC S7- 1200/ S7- 1500 Entry ID: 101908495, V1.0, 10/2014... an existing S7- 1500 program Process 6 Action Optional: Realize a protected connection to S7- 1500 by entering a password ã Siemens AG Copyright- 2014 All rights reserved Note Password protection is only provided by S7- 1500 CPUs Further information is available in the manual: "SIMATIC S7- 1500 Automation System > Protection > Configuring access protection for the CPU" \3\ 7 WinCC S7- 1200/ S7- 1500 Entry... Starting WinCC Runtime Start WinCC Runtime 10/2014 11 3 Configuration and Settings 3.1 Loading AS symbols from an existing S7- 1500 program Process ã Siemens AG Copyright- 2014 All rights reserved 8 Action Reading AS symbols Right-click on the connection and go to "AS Symbols -> Read from AS" to read out the symbols of the S7- 1500 These are read now Confirm the message with OK WinCC S7- 1200/ S7- 1500 Entry... Loading AS symbols from an existing S7- 1500 program Process Action The symbols of the S7- 1500 are now listed under "AS Symbols": 10 ã Siemens AG Copyright- 2014 All rights reserved 9 By checking the "Access" check box, the tags with symbolic addressing are automatically created 11 These are now displayed on the "Tags" tab together with their properties WinCC S7- 1200/ S7- 1500 Entry ID: 101908495, V1.0,... from an existing S7- 1500 program Process Action ã Siemens AG Copyright- 2014 All rights reserved 2 Under "AS Messages", right-click on the connection "NewConnection_1" to open the context menu 3 Click on "Load from AS" to import the system messages WinCC S7- 1200/ S7- 1500 Entry ID: 101908495, V1.0, 10/2014 16 3 Configuration and Settings 3.2 Loading AS messages from an existing S7- 1500 program Process... messages is only possible with an S7- 1500 WinCC S7- 1200/ S7- 1500 Entry ID: 101908495, V1.0, 10/2014 17 4 References 4 References Table 4-1 Subject Title \1\ Download page of the entry http://support.automation.siemens.com/WW/view/en/101908495 \3\ ã Siemens AG Copyright- 2014 All rights reserved http://support.automation.siemens.com \2\ 5 Siemens Industry Online Support S7- 1500 Manual; Access Protection... Online Support S7- 1500 Manual; Access Protection https://www.automation.siemens.com/mdm/default.aspx?DocVersionI d=63956397195&TopicId=62467847691 History Table 5-1 Version Date V1.0 10/2014 WinCC S7- 1200/ S7- 1500 Entry ID: 101908495, V1.0, 10/2014 Modifications First version 18 ... 3 Configuration and Settings 3.1 Loading AS symbols from an existing S7- 1500 program Process ã Siemens AG Copyright- 2014 All rights reserved 12 Action You can change the tag name on the "Tags" and "AS Symbols" tabs Note If modifications are made to the controller, it is necessary to execute the "Read from AS" command again Note If WinCC Runtime is stopped and Tag Management is closed, neither the symbolic . solution: Figure 2-1 S7- 1500 S7- 1200 PROFINET IE WinCC V7.3 SIMATIC S -1200, S7- 1500 Channel Description WinCC V7.3 provides the communication channel "SIMATIC S7- 1200, S7- 1500 Channel". with S7- 1200 and S7- 1500 CPUs. Communication to S7- 1200 and S7- 1500 can be realized with absolute addressing and since WinCC V7.3 also with symbolic addressing. Between WinCC V7.3 and S7- 1500, . Started S7- 1500 101908495 _WinCC_ S71 200 _S71 500_Chanel_de.pdf This document. 3 Configuration and Settings 3.1 Loading AS symbols from an existing S7- 1500 program WinCC S7- 1200/ S7- 1500 Entry ID: 101908495,