anshcpu anacpu anucpu qcpu a a mode dedicated

[...]... the AnSHCPU and automatic refresh is performed between the AnSHCPU and master/local module (3) If the automatic refresh parameters are changed (RRPA instruction is executed) during RUN, new data is not used for control When the AnSHCPU is switched to STOP/PAUSE, then to RUN, the new automatic refresh parameters are used for refreshing 16-10 IB(NA)66251-E RRPA (4) Setting is made in the parameter areas... and preset data AD59 (S1) control instruction Output of data to a printer, read/write of data with a memory card AJ71C24 (S3, S6, S8) /AJ71UC24 control instruction Data communication with an external device in the no-protocol mode AJ71C21 (S1) control instruction Data communication with an external device in the no-protocol mode and RAM data read/write AJ71PT32-S3 control instruction Special function... instruction Expansion file register instruction Section 9 Conversion between binary/BCD data and character-string data, transmission, comparison, separation and joining of character-string data, and reading device comments Upper/lower range check for input data, immune zone check, and zone control in which a fixed value is added Section 10 Read/write of year, month, day, data, hour, minute, and second... Section 11 Vacant area in a memory cassette is used as file register Section 12 In the MELSECNET data link system, the master station executes communication with local and remote I/O stations Data link instruction In the MELSECNET/10 data link system, the master station executes data communication with the MELSECNET/10 stations AD61 (S1) control instruction Reading count value and writing set data and preset... of the data with handshake is enabled for a remote device Which of the dedicated instructions for the CC-Link (8 kinds) can be used at which station is shown below in Table 16.1 Table 16.1 Dedicated Instructions Usable at Each Station Usability Station Instruction Refer to Description RLPA RRPA Master station Local station Sets the network parameters Sets the automatic refresh parameters RIRD RIWT... For inputting key entry data using AJ35PT-OPB-M1/AJ35TOPB-P1 operation box • For sending data to AJ35PTF-R2 RS-232C interface module • For receiving data from AJ35PTF-R2 RS-232C interface module • Read/write of data with MINI standard protocol compatible remote terminal unit AD57(S1)/AD58 CRT/LCD controller unit (Refer to AnACPU Programming Manual (AD57 Instructions)) The special function module instructions... The dedicated instructions for the CC-Link network system are used for the setting of automatic refreshing of the AnSHCPU and the master module/local module, and also for data communications with the remote station connected to the CC-Link network system Transient transmission to an intelligent device station and a local station is possible using the dedicated instructions Read/write of the data with... network parameters, new data is not used for communication with the slave stations When the AnSHCPU is switched to STOP/PAUSE, then to RUN, the new network parameters are used for communication with the slave stations (4) Execution of the RLPA instruction automatically starts the data link 16-5 IB(NA)66251-E RLPA Execution Conditions As shown below, when the LEDA instruction is used, the RLPA instruction... program sets the automatic refresh parameters to the master module of CC-Link allocated to I/O numbers 000 to 01F: (1) Automatic refresh parameter settings and data storage devices Setting Item RX's head number AnSHCPU side refreshed device code AnSHCPU side refreshed device's head number Number of refresh points RY's head number AnSHCPU side refreshed device code AnSHCPU side refreshed device's head... memory address specified at n3 for the station having the station number specified at n2 in the master module specified at n1 and stores that data into the devices starting from the one specified at D RIFR instruction execution range AnSHCPU Mater station Intelligent device /local station n2 n1 RIFR instruction n3 D Specified device Automatic updating buffer memory Transferred when data is updated n4 . program instructions that are expanded for dedicated use with the A2 ACPU(S1) and A3 ACPU (hereafter called the AnACPU) and A2 UCPU(S1), A3 UCPU and A4 UCPU, A2 ASCPU(S1/S30/S60) (hereafter called. (NA)-66257 AnACPU/ AnUCPU Programming Manual (PID control instructions) IB (NA)-66258 Refer to the following manuals for information on the use of the AnSHCPU, AnACPU and AnUCPU: A2 A(S1) /A3 ACPU. User’s Manual IB (NA)-66544 A2 U(S1) /A3 UCPU /A4 UCPU User’s Manual IB (NA)-66436 A2 ASCPU(S1) User’s Manual IB (NA)-66455 A1 SJH /A1 SH /A2 SHCPU(S1) User’s Manual IB (NA)-66779 AJ61BT11, A1 SJ61BT11,