1. Trang chủ
  2. » Kỹ Thuật - Công Nghệ

Autodesk Revit Architecture 2011 No Experience Required - part 11 docx

10 374 0

Đang tải... (xem toàn văn)

THÔNG TIN TÀI LIỆU

Thông tin cơ bản

Định dạng
Số trang 10
Dung lượng 549,9 KB

Nội dung

To start the wall, pick the intersection where the CMU wall abuts the finish inside face of the exterior wall see Figure 2.49.. On the Geometry panel of the Modify tab, click the Wall J

Trang 1

let’s add some more walls to an already busy corner of the building:

1 Zoom into the northeast corner of the building, as shown in

Figure 2.48

F i g u R e 2 4 8 The northeast corner

partition you have been using

3 To start the wall, pick the intersection where the CMU wall abuts the

finish inside face of the exterior wall (see Figure 2.49)

4 The wall may be flipped in the wrong direction If it is, remember to

hit the spacebar This will flip it up to the proper orientation Look ahead to Figure 2.50 for the orientation

5 Pick the second point of the wall at the corridor in the middle of

the building Press Esc twice The intersection should look like Figure 2.50

Trang 2

E d i t i n g W a l l J o i n s 7 5

F i g u R e 2 4 9 Adding to the mess in the corner

F i g u R e 2 5 0 The wall and the resulting intersection

6 Zoom back in on the intersection If the view does not resemble

Figure 2.50 in terms of line weight, click the Thin Lines icon, as

shown in Figure 2.51

F i g u R e 2 5 1 Click the Thin Lines icon to see how the walls are joining

together.

7 On the Geometry panel of the Modify tab, click the Wall Joins button,

as shown in Figure 2.52

Trang 3

F i g u R e 2 5 2 You’ll find the Wall Joins button on the Modify tab.

8 Hover your pointer over the intersection Revit will display a big box,

as shown in Figure 2.53

9 When you see the big box, pick anywhere within the area This will

establish that this is the intersection you wish to edit

F i g u R e 2 5 3 Choosing the intersection you wish to edit

Trang 4

E d i t i n g W a l l J o i n s 7 7

After you pick the intersection, you will see some additional lines

show up These additional lines expose how Revit is actually looking

at the corner

10 On the Options bar, you will now see some choices for configuring

this intersection Select the Miter option, as shown in Figure 2.54

This option is the most popular

Although a wall of this type would never have a 45° miter in real

life, mitering the corner in Revit allows for a more uniform join

between adjacent walls

F i g u R e 2 5 4 Adding a mitered join

displaying Wall Joins

Usually, in a plan view such as this, there will be no wall joins shown at all Typically

only the outside lines join and an enlarged detail would show the specific

construc-tion methods But in some cases, you would want Revit to reveal this informaconstruc-tion

In Revit, you have three choices for the display:

clean Join Clean Join will join together the same materials in each wall.

don’t clean Join Don’t Clean Join will take one wall and indiscriminately run it

straight through to the end

use view setting Use View Setting will take you to the View Properties,

where you can specify the default for how to display the wall intersections (see

Figure 2.55)

Trang 5

F i g u R e 2 5 5 Choosing a display option

The objective of the next procedure is to investigate where the wall join set-tings are located:

1 Choose Use View Setting.

2 Press Esc a few times and click on the drawing.

3 Type VP to open the View Properties dialog.

4 In the Properties dialog, you will see a category for Wall Join Display

It is set to Clean All Wall Joins; it is also unavailable for editing If your view’s detail level is set to Fine, the default is to clean all joins If

it is set to Coarse, as shown in Figure 2.56, you have a choice between joining the same wall types or cleaning all joins

5 Do not change anything here.

F i g u R e 2 5 6 Choosing a Wall Join Display option in the view’s properties

Trang 6

E d i t i n g W a l l J o i n s 7 9

disallowing Wall Join

You must deal with another important item when walls join together In some

cases, you may not want walls to automatically join even if they are the same

exact wall type To learn how to prevent this behavior, follow along:

shown in Figure 2.57 You will see a blue grip to the right of the

inter-section This represents where the wall’s extents are

2 Hover directly over the blue grip.

3 After the blue grip highlights, right-click.

4 Select Disallow Join (see Figure 2.57).

F i g u R e 2 5 7 By right-clicking on the wall’s end grip, you can tell Revit to

disallow that wall’s join function.

5 After the wall is un-joined, you can pick the same blue grip and slide

the wall back to where you would want it to terminate Of course, you

will have to do this manually (see Figure 2.58)

6 After the wall slides into place, select it.

Trang 7

F i g u R e 2 5 8 Allowing the walls to join back again

As mentioned earlier, your ability to edit wall joins can determine how quickly you start either liking, or disliking, Revit This book took a few extra steps in the effort of joining walls, but the experience will carry through, project after project There is one more area we need to investigate before we leave this corner: the area within the chase Suppose you do not want to run the gypsum into this area This is a common situation that can cause people to have fits with Revit Let’s try to avoid those fits right now!

editing the cut Profile

A plan view is simply a section taken 4′–0″ up the wall from the finish floor In Revit, you can manually edit the profile of any wall cut in plan This is extremely useful if you need to take sections of drywall out of specific areas without creat-ing or addcreat-ing an entirely new wall To do this, perform the followcreat-ing steps:

1 Zoom in on the right side of the elevator shaft at the intersection of

the exterior wall, as shown in Figure 2.59

2 Select the east CMU wall, and drag it out of the exterior wall by

picking and dragging the blue grip at the end of the wall (see Figure 2.59)

3 Right-click on the blue grip on the endpoint of the wall.

4 Select Disallow Join.

5 Pick the blue grip and drag the wall end back to the face of the wall

behind the gypsum (see Figure 2.60)

Trang 8

E d i t i n g W a l l J o i n s 8 1

F i g u R e 2 5 9 Pick the blue grip and drag the CMU wall out of the

exterior wall.

F i g u R e 2 6 0 Pull the CMU out of the wall, disallow the join, and then

drag it back into the face of the stud.

6 On the Graphics panel of the View tab, click the Cut Profile button, as

shown at the top right of Figure 2.61

7 Pick the finish face of the exterior wall You are selecting the gypsum

layer to be cut out of the shaft (see Figure 2.61)

F i g u R e 2 6 1 Click the Cut Profile button and select the gypsum.

Trang 9

F i g u R e 2 6 2 This line indicates where the wallboard will be cut The blue

arrow indicates the side of the material that will remain.

10 What you see here is called the Sketch Mode Since you are done

“sketching” the cut profile, click Finish Edit Mode, as you can see in Figure 2.63 Figure 2.64 shows the final result

F i g u R e 2 6 3 Clicking Finish Edit Mode will finalize the session and

complete the command.

N O T E If you receive an error that says “ends of the sketched loop

do not lie on the boundary of the face being modified” when you are trying

to finish the sketch, it is because you have not drawn the line exactly from point to point this line cannot cross over, or be shy of, the material you are trying to split If you are getting this error, select the magenta line You will see two familiar blue grips pick the grip that does not touch the face of the material and drag it back

Trang 10

P l a c i n g D o o r s a n d W i n d o w s 8 3

F i g u R e 2 6 4 The finished wall with the drywall deducted from the core of

the chase

Go through and do the same thing to the south side of the building, starting

at the edit Wall Joins section

There are plenty more walls left to add, but we need to save something for

Chapter 4 At this point, it sure would be nice to start adding some doors and

windows to the model!

Placing doors and Windows

Adding doors and windows is one of the easiest things you will do in Revit

Architecture Finding the correct door or window becomes a bit harder Creating

a custom door or window takes time and patience In this section, we will focus

on adding these items to the model Chapter 17, “Creating Families,” will drill

down into the specifics of creating these custom families

Adding doors

Placing a door in Revit Architecture can seem annoying and unnecessarily tedious

at first But like anything else in Revit, once you get the method down, you will find

your groove

1 Either continue working in your current model, or go to www.sybex

model is completed up to this point Of course, you can translate

these lessons to your own project as well

2 On the Home tab, click the Door button (see Figure 2.65).

Ngày đăng: 07/07/2014, 07:20

TỪ KHÓA LIÊN QUAN

TÀI LIỆU CÙNG NGƯỜI DÙNG

TÀI LIỆU LIÊN QUAN

w