Tài liệu hướng dẫn sửa chữa xe Toyota rush daihatsu terios 2006 2012 wiring diagram tai lieu sua chua phan 8. Cung cấp các thông tin cần thiết cho Kỹ thuật viên tiến hành chẩn đoán, sửa chữa nhanh chóng, chính xác, hiệu quả, nhanh chóng.
ET–13 BODY EXTERIOR - SIDE MUD GUARD LH SIDE MUD GUARD LH BODY EXTERIOR AND ELECTRICAL COMPONENTS QUARTER PANEL MUD GUARD RR LH ET FRONT FENDER MUD GUARD LH B142171J01 REMOVAL Clip B140049J01 REMOVE FRONT FENDER MUD GUARD LH (a) Remove the clips and the front fender mud guard LH ET–14 BODY EXTERIOR - SIDE MUD GUARD LH Remove the quarter panel mud guard RR LH (a) Remove the clips and the quarter panel mud guard RR LH INSTALLATION Clip Clip ET Clip B140050J01 INSTALL FRONT FENDER MUD GUARD LH (a) Install the front fender mud guard LH with the clips INSTALL QUARTER PANEL MUD GUARD RR LH (a) Install the quarter panel mud guard RR LH with the clips B140049J01 B140050J01 ET–15 BODY EXTERIOR - NAME PLATE NAME PLATE BODY EXTERIOR AND ELECTRICAL COMPONENTS (1) (2) (3) (4) (1)BACK DOOR NAMEPLATE NO (3)BACK DOOR NAMEPLATE NO 2.7 Back Door Edge Back Door Edge Body Crease ET 218.5 Body Crease 2.4 Back Door Edge Body Crease 132 Backing Paper(Template) (2)BACK DOOR NAMEPLATE NO (4)BACK DOOR NAMEPLATE NO Back Door Edge Perforated Line Body Crease Units [mm] Backing Paper(Template) B141317J01 ET–16 BODY EXTERIOR - ROOF DRIP SIDE FINISH MOULDING LH ROOF DRIP SIDE FINISH MOULDING LH BODY EXTERIOR AND ELECTRICAL COMPONENTS ROOF RACK EQUIPPED VEHICLE ROOF RACK LEG COVER RR LH ROOF RACK LEG COVER FR LH T=31{316} T=31{316} ROOF RACK LEG CUSHION RR LH ROOF RACK ASSEMBLY LH ROOF RACK LEG CUSHION FR LH ROOF DRIP SIDE FINISH MOLDING FR LH ROOF DRIP SIDE FINISHMOLDING CLIP ROOF DRIP SIDE FINISH MOLDING CLIP NO ET NON-REUSEABLE PART TIGHTENING TORQUE [N*m{kgf*cm}] B143265J01 BODY EXTERIOR - ROOF DRIP SIDE FINISH MOULDING LH ET–17 REMOVAL REMOVE ROOF RACK LEG COVER FR LH (WITH ROOF RACK) (See page ET-46) REMOVE ROOF RACK LEG COVER RR LH (WITH ROOF RACK) (See page ET-46) REMOVE ROOF RACK ASSEMBLY LH (WITH ROOF RACK) (See page ET-46) REMOVE ROOF RACK LEG CUSHION FR LH (WITH ROOF RACK) REMOVE ROOF RACK LEG CUSHION RR LH (WITH ROOF RACK) REMOVE ROOF DRIP SIDE FINISH MOULDING FR LH (a) Put protective tape on the body panel around the roof drip side finish moulding outline (b) Disengage the clips and remove the roof drip finish moulding NOTICE: • Do not remove the clip • If the clips are damaged, replace them with extra clips INSTALLATION Protective Tape HINT: If the clips have come off or damaged, follow steps to Clip B140048J01 CLEAN INSTALLATION SURFACE (a) Heat the double-sided tape on the body using a heat gun Then wipe off the tape using a rag or piece of cloth (b) Clean the surface with a solvent INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP (a) Put a one-to-one ratio of base compound to hardening agent of adhesive in a plastic bag or similar container Mix them until the color of the mixture changes from clear to milky white NOTICE: • Be sure to mix the base compound and hardening agent in a one-to-one ratio If they are not mixed in the specified ratio, adhesion will significantly decrease • Thoroughly mix the base compound and hardening agent Failure to so will result in poor hardening • Apply the mixture within 20 minutes of mixing (b) 0.5mm or more B147243 Coat the clip with adhesive so that the thickness of the adhesive is 0.5 mm or more Standard: When press-firring the clip, the adhesive protrudes from the outer edge ET ET–18 BODY EXTERIOR - ROOF DRIP SIDE FINISH MOULDING LH (c) A C B After applying the adhesive, attach the clip to the position shown in the illustration and firmly press-fit the clip HINT: • Do not touch the adhesive surface with your fingertips, etc • Keep the adhesive surface away from oil, water, dirt, and other foreign objects • Press-fit the clip at right angles to the body Symbols D E F (d) 1.2 B 1±0.5 C 1.3±1 D 5.4 E 1±0.5 F 1.3±1 Harden the adhesive HINT: Heating the adhesive will facilitate hardening hours or more at room temperature Heat adhesive 30 minutes or more at 80°C (e) Install the roof drip side finish moulding FR LH and then remove it Check that the clip is securely attached INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP NO INSTALL ROOF DRIP SIDE FINISH MOULDING FR LH (a) Attach the clips and install the roof drip side finish moulding FR LH A ET (b) B140048J02 A Leave adhesive unattended B140047J01 B Specified value (mm) Symbols Specified value (mm) A 18.5 B 18 Remove the protective tape INSTALL ROOF RACK LEG CUSHION RR LH INSTALL ROOF RACK LEG CUSHION FR LH INSTALL ROOF RACK ASSEMBLY LH (See page ET-47) INSTALL ROOF RACK LEG COVER RR LH (See page ET-47) INSTALL ROOF RACK LEG COVER FR LH (See page ET-48) BODY EXTERIOR - ROCKER PANEL MOULDING LH ET–19 ROCKER PANEL MOULDING LH BODY EXTERIOR AND ELECTRICAL COMPONENTS MOLDING TAPE NO.3 MOLDING TAPE NO.2 ET ROCKER PANEL MOLDING LH SIDE MUD GUARD RETAINER NON-REUSEABLE PART B142176J01 ET–20 BODY EXTERIOR - ROCKER PANEL MOULDING LH REMOVAL REMOVE SIDE MUD GUARD RETAINER (a) Remove the side mud guard retainers using a wide type handy remover B144221 REMOVE ROCKER PANEL MOULDING LH (a) Remove the screws ET B144222 BODY EXTERIOR - ROCKER PANEL MOULDING LH (b) ET–21 Apply protective tape as shown in the illustration MOLDING TAPE NO.3 Protective Tape MOLDING TAPE NO.2 :Clip B139164J01 (c) (d) Using a heat gun, heat the rocker panel moulding LH (double sided adhesive area) Using a wide type handy remover, remove the claws and connectors (double sided tape) Then remove the locker panel moulding LH REMOVE MOULDING TAPE NO REMOVE MOULDING TAPE NO INSTALLATION CLEAN INSTALLATION SURFACE (a) Heat the moulding tape on the body using a heat gun Then wipe off the tape using a rag or piece of cloth (b) Clean the surface with a solvent CLEAN ROCKER PANEL MOULDING LH (WHEN REUSING) (a) CLEAN MOULDING TAPE INSTALLATION SURFACE (1) Using a heat gun, heat the moulding tape remaining on the rocker panel moulding LH (2) While heating the tape with the heat gun, use a rag or piece of cloth to wipe off the moulding tape remaining on the rocker panel moulding LH NOTICE: • Remove as much of the moulding tape as possible Any tape that remains may cause attachment failure when the rocker panel moulding is installed • Use a waste cloth to scrub off, because it may cause damage and attachment failure if using a driver (3) Clean the surface with a solvent ET ET–22 BODY EXTERIOR - ROCKER PANEL MOULDING LH INSTALL MOULDING TAPE NO (a) Attach the moulding tape No to the rocker panel moulding LH as shown in the illustration MOLDING TAPE NO.3 MOLDING TAPE NO.2 B147469J01 NOTICE: Be careful not to touch the adhesive surface with your fingers when removing the exfoliate paper from the moulding tape ET INSTALL MOULDING TAPE NO (a) Attach the moulding tape No to the rocker panel moulding LH as shown in the illustration NOTICE: Be careful not to touch the adhesive surface with your fingers when removing the exfoliate paper from the moulding tape INSTALL ROCKER PANEL MOULDING LH (a) Using a heat gun, heat the rocker panel moulding LH and the surface of the vehicle body (b) Set the rocker panel moulding LH on the vehicle, and press firmly to install it NOTICE: Be careful not to touch the adhesive surface with your fingers when removing the exfoliate paper from the moulding tape (c) Attach the claws and install the rocker panel moulding LH MOLDING TAPE NO.3 Protective Tape MOLDING TAPE NO.2 :Clip B139164J01