Iec Tr 61010-3-043-2001.Pdf

TECHNICAL REPORT IEC TR 61010-3-043 First edition 2001-08 Part 3-043: Conformity verification report for IEC 61010-2-043:1997 – Particular requirements for dry heat sterilizers using either hot air or hot inert gas for treatment of medical materials and for laboratory processes Règles de sécurité pour appareils électriques de mesurage, de régulation et de laboratoire – Partie 3-043: Rapport de vérification de la conformité de la CEI 61010-2-043:1997 – Prescriptions particulières pour les stérilisateurs chaleur utilisant de l'air chaud ou un gaz inerte chaud pour le traitement des matériels usage médical et durant les procédés de traitement de laboratoire Reference number IEC/TR 61010-3-043:2001(E) LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU Safety requirements for electrical equipment for measurement, control, and laboratory use – Publication numbering As from January 1997 all IEC publications are issued with a designation in the 60000 series For example, IEC 34-1 is now referred to as IEC 60034-1 Consolidated editions The IEC is now publishing consolidated versions of its publications For example, edition numbers 1.0, 1.1 and 1.2 refer, respectively, to the base publication, the base publication incorporating amendment and the base publication incorporating amendments and The technical content of IEC publications is kept under constant review by the IEC, thus ensuring that the content reflects current technology Information relating to this publication, including its validity, is available in the IEC Catalogue of publications (see below) in addition to new editions, amendments and corrigenda Information on the subjects under consideration and work in progress undertaken by the technical committee which has prepared this publication, as well as the list of publications issued, is also available from the following: • IEC Web Site (www.iec.ch) • Catalogue of IEC publications The on-line catalogue on the IEC web site (www.iec.ch/catlg-e.htm) enables you to search by a variety of criteria including text searches, technical committees and date of publication On-line information is also available on recently issued publications, withdrawn and replaced publications, as well as corrigenda • IEC Just Published This summary of recently issued publications (www.iec.ch/JP.htm) is also available by email Please contact the Customer Service Centre (see below) for further information • Customer Service Centre If you have any questions regarding this publication or need further assistance, please contact the Customer Service Centre: Email: custserv@iec.ch Tel: +41 22 919 02 11 Fax: +41 22 919 03 00 LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU Further information on IEC publications TECHNICAL REPORT IEC TR 61010-3-043 First edition 2001-07 LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 3-043: Conformity verification report for IEC 61010-2-043:1997 – Particular requirements for dry heat sterilizers using either hot air or hot inert gas for treatment of medical materials and for laboratory processes Règles de sécurité pour appareils électriques de mesurage, de régulation et de laboratoire – Partie 3-043: Rapport de vérificatoin de la conformité de la CEI 61010-2-043:1997 – Prescriptions particulières pour les stérilisateurs chaleur utilisant de l'air chaud ou un gaz inerte chaud pour le traitement des matériels usage médical et durant les procédés de traitement de laboratoire  IEC 2001  Copyright - all rights reserved No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher International Electrotechnical Commission 3, rue de Varembé Geneva, Switzerland Telefax: +41 22 919 0300 e-mail: inmail@iec.ch IEC web site http://www.iec.ch Commission Electrotechnique Internationale International Electrotechnical Commission PRICE CODE XA For price, see current catalogue –2– TR 61010-3-043  IEC:2001(E) CONTENTS FOREWORD Conformity verification report IEC 61010-2-043 5 Marking and documentation 10 Protection against electric shock .14 Protection against mechanical hazards 21 Mechanical resistance to shock and impact .23 Equipment temperature limits and protection against the spread of fire 23 10 Resistance to heat 24 12 Protection against radiation, including laser sources, and against sonic and ultrasonic pressure 26 13 Protection against liberated gases, explosion and implosion 26 14 Components 27 15 Protection by interlocks 29 16 Measuring circuits 29 Annex K………… 30 Table – Documents attached to this report Table – Test equipment list Table – List of components relied on for safety Form A.1 to Form A.29 30 to 59 LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU 11 Protection against hazards from fluids .25 C.vT.Bg.Jy.Lj.Tai lieu Luan vT.Bg.Jy.Lj van Luan an.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj Do an.Tai lieu Luan van Luan an Do an.Tai lieu Luan van Luan an Do an TR 61010-3-043  IEC:2001(E) –3– INTERNATIONAL ELECTROTECHNICAL COMMISSION _ SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL, AND LABORATORY USE – Part 3-043: Conformity verification report for IEC 61010-2-043:1997– Particular requirements for dry heat sterilizers using either hot air or hot inert gas for treatment of medical materials and for laboratory processes 1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees) The object of the IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields To this end and in addition to other activities, the IEC publishes International Standards Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation The IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations 2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested National Committees 3) The documents produced have the form of recommendations for international use and are published in the form of standards, technical specifications, technical reports or guides and they are accepted by the National Committees in that sense 4) In order to promote international unification, IEC National Committees undertake to apply IEC International Standards transparently to the maximum extent possible in their national and regional standards Any divergence between the IEC Standard and the corresponding national or regional standard shall be clearly indicated in the latter 5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with one of its standards 6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights The IEC shall not be held responsible for identifying any or all such patent rights The main task of IEC technical committees is to prepare International Standards However, a technical committee may propose the publication of a technical report when it has collected data of a different kind from that which is normally published as an International Standard, for example “state of the art” Technical reports not necessarily have to be reviewed until the data they provide are considered to be no longer valid or useful IEC 61010-3-043, which is a technical report, has been prepared by IEC technical committee 66: Safety of measuring, control, and laboratory equipment The text of this technical report is based on the following documents: Committee draft Report on voting 66/223/CDV 66/230/RVC Full information on the voting for the approval of this technical report can be found in the report on voting indicated in the above table Stt.010.Mssv.BKD002ac.email.ninhd.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj.dtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn.Stt.010.Mssv.BKD002ac.email.ninhddtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU FOREWORD C.vT.Bg.Jy.Lj.Tai lieu Luan vT.Bg.Jy.Lj van Luan an.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj Do an.Tai lieu Luan van Luan an Do an.Tai lieu Luan van Luan an Do an –4– TR 61010-3-043  IEC:2001(E) This publication has been drafted in accordance with the ISO/IEC Directives, Part This report is a Technical Report and is of a purely informative nature and is therefore by itself not to be regarded as an International Standard It is for use by test houses and other users to assist them with determining and recording verification of conformity of the equipment under test with the requirements of: IEC 61010-2-043: 1997 and IEC 61010-1:1990 + amendment 1:1992 + amendment 2:1995 The IEC sells read-only PDF files as a general rule In the present instance, and quite exceptionally, to enable the user to fill in the forms, a revisable file is included in a pocket affixed to the back cover of this publication This file can also be downloaded from the Web as a PDF file There is, however, at the end of the document, a revisable file containing the forms Please use the zip/unzip function A bilingual version will not be issued A French version may be issued The committee has decided that the contents of this publication will remain unchanged until 2004 At this date, the publication will be • reconfirmed; • withdrawn; • replaced by a revised edition, or • amended Stt.010.Mssv.BKD002ac.email.ninhd.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj.dtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn.Stt.010.Mssv.BKD002ac.email.ninhddtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU The protocol for completion of this report is contained in publication IEC 61010-3:1997 C.vT.Bg.Jy.Lj.Tai lieu Luan vT.Bg.Jy.Lj van Luan an.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj Do an.Tai lieu Luan van Luan an Do an.Tai lieu Luan van Luan an Do an TR 61010-3-043  IEC:2001(E) –5– Conformity Verification Report IEC 61010-2-043 Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-043: Particular requirements for dry heat sterilizers using either hot air or hot inert gas for treatment of medical materials, and for laboratory processes Report reference No : Compiled by (+ signature) : Approved by (+ signature) : Testing organization : Address : Testing location : Applicant : Address .: Standard : IEC 61010-2-043:1997 and IEC 61010-1:1990 + amendment 1:1992 + amendment 2:1995 Copyright blank test report : This report has been prepared by IEC/TC 66, which retains responsibility for any changes or corrections required Test procedure : Procedure deviation : Non-standard test method : Type of item tested : Laboratory Trademark : Model/type reference : Manufacturer .: Rating : Copy of rating plate: Stt.010.Mssv.BKD002ac.email.ninhd.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj.dtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn.Stt.010.Mssv.BKD002ac.email.ninhddtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU Date of issue .: C.vT.Bg.Jy.Lj.Tai lieu Luan vT.Bg.Jy.Lj van Luan an.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj Do an.Tai lieu Luan van Luan an Do an.Tai lieu Luan van Luan an Do an TR 61010-3-043  IEC:2001(E) –6– Description of equipment function : I NSTALLATION / OVERVOLTAGE CATEGORY: P OLLUTION DEGREE : Environmental rating: Connection to mains supply: Operating conditions: Other (specify): Portable Built in Hand-held Benchmounted Permanent Continuous Detachable Short-time Overall size of the equipment (Length x Width x Height): Mass of the equipment (kg): Marked degree of protection to IEC 60529: IP _ _ Accessories and detachable parts included in the evaluation: Options: NOTE Floorstanding Other (specify): "(see form A.X)" refers to a form appended to the report Stt.010.Mssv.BKD002ac.email.ninhd.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj.dtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn.Stt.010.Mssv.BKD002ac.email.ninhddtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn Fixed Non-detachable Intermittent None LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU Equipment mobility: Standard C.vT.Bg.Jy.Lj.Tai lieu Luan vT.Bg.Jy.Lj van Luan an.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj Do an.Tai lieu Luan van Luan an Do an.Tai lieu Luan van Luan an Do an TR 61010-3-043  IEC:2001(E) –7– Table – Documents attached to this report Document No Document description Number of pages LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU Stt.010.Mssv.BKD002ac.email.ninhd.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj.dtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn.Stt.010.Mssv.BKD002ac.email.ninhddtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn C.vT.Bg.Jy.Lj.Tai lieu Luan vT.Bg.Jy.Lj van Luan an.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj Do an.Tai lieu Luan van Luan an Do an.Tai lieu Luan van Luan an Do an TR 61010-3-043  IEC:2001(E) –8– Table – Test equipment list Item Type Equipment No Calibration date Last 1) Comments Due LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU 1) or interval between calibrations Stt.010.Mssv.BKD002ac.email.ninhd.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj.dtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn.Stt.010.Mssv.BKD002ac.email.ninhddtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn C.vT.Bg.Jy.Lj.Tai lieu Luan vT.Bg.Jy.Lj van Luan an.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj Do an.Tai lieu Luan van Luan an Do an.Tai lieu Luan van Luan an Do an Form A 20 Mechanical resistance to shock and impact Voltage tests can be carried out once after performing the tests of Clause and Clause 11 However, if voltage tests are carried out separately after each set of tests, two forms can be used Clause tests Location Rigidity (see Form A.5) Impact Hammer (8.1) (8.2) Clause 11 tests Drop 8.4.1 and 8.4.2 Normal Handheld Cleaning Spillage Overflow IEC 60529 (11.2) (11.3) (11.4) (11.6) Working voltage Test voltage Result (note) (note) Pass/ V V Fail Comments – 50 – Use r.m.s., d.c or peak to indicate the used test voltage Tested by: _Date: _Test equipment No (Table 2) _ Stt.010.Mssv.BKD002ac.email.ninhd.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj.dtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn.Stt.010.Mssv.BKD002ac.email.ninhddtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn TR 61010-3-043  IEC:2001(E) NOTE LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU 11 Protection against hazards from fluids C.vT.Bg.Jy.Lj.Tai lieu Luan vT.Bg.Jy.Lj van Luan an.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj Do an.Tai lieu Luan van Luan an Do an.Tai lieu Luan van Luan an Do an TR 61010-3-043  IEC:2001(E) – 51 – Form A.21 11.7.2 Leakage and rupture at high pressure Part Maximum permissible working pressure MPa Factor (Figure of IEC 61010-1) Test pressure Leakage test MPa Pass/Fail Burst test Pass/Fail Test equipment No (Table 2) 11.7.3 Leakage from low-pressure parts Part Test pressure MPa Leakage test Pass/Fail Tested by: _Date: _ Test equipment No (Table 2) _ Stt.010.Mssv.BKD002ac.email.ninhd.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj.dtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn.Stt.010.Mssv.BKD002ac.email.ninhddtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn Comments LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU Tested by: _Date: Comments C.vT.Bg.Jy.Lj.Tai lieu Luan vT.Bg.Jy.Lj van Luan an.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj Do an.Tai lieu Luan van Luan an Do an.Tai lieu Luan van Luan an Do an – 52 – TR 61010-3-043  IEC:2001(E) Form A.22 12.2.1 Ionizing radiation Locations tested Measured values µSv/h Result Pass/Fail Comments LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU General comments: Tested by: Date: _ Test equipment No (Table 2) _ Stt.010.Mssv.BKD002ac.email.ninhd.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj.dtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn.Stt.010.Mssv.BKD002ac.email.ninhddtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn C.vT.Bg.Jy.Lj.Tai lieu Luan vT.Bg.Jy.Lj van Luan an.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj Do an.Tai lieu Luan van Luan an Do an.Tai lieu Luan van Luan an Do an TR 61010-3-043  IEC:2001(E) – 53 – 12.5.1 Sound level Measured values Locations tested Calculated maximum sound pressure level dBA At OPERATOR ’s normal position and at bystanders positions a) b) c) d) e) Tested by: _Date: Test equipment No (Table 2) 12.5.2 Ultrasonic pressure Measured values Locations tested dB Comments kHz At OPERATOR ’s normal position At m from the ENCLOSURE a) b) c) d) e) NOTE No limit is specified at present, but a limit of 110 dB above the reference pressure value of 20 µPa is under consideration for applicable frequencies between 20 kHz and 100 kHz Result Pass/Fail Comments: Tested by: _Date: Test equipment No (Table 2) Stt.010.Mssv.BKD002ac.email.ninhd.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj.dtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn.Stt.010.Mssv.BKD002ac.email.ninhddtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU Comments: C.vT.Bg.Jy.Lj.Tai lieu Luan vT.Bg.Jy.Lj van Luan an.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj Do an.Tai lieu Luan van Luan an Do an.Tai lieu Luan van Luan an Do an – 54 – TR 61010-3-043  IEC:2001(E) Form A.24 13.2.2 Batteries Battery load and charging circuit diagram: Battery manufacturer/model/catalogue No.: Battery ratings: Reverse polarity instalment test – Result (Pass/Fail): Single component failures Result Pass/Fail Component Open circuit Comments: Tested by: _Date: Test equipment No (Table 2) Stt.010.Mssv.BKD002ac.email.ninhd.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj.dtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn.Stt.010.Mssv.BKD002ac.email.ninhddtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn Short-circuit LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU Battery type: C.vT.Bg.Jy.Lj.Tai lieu Luan vT.Bg.Jy.Lj van Luan an.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj Do an.Tai lieu Luan van Luan an Do an.Tai lieu Luan van Luan an Do an TR 61010-3-043  IEC:2001(E) – 55 – Form A.25 4.4.2.4 S INGLE FAULT CONDITIONS , motors 14.2.1 Motor temperatures Operating conditions: Frequency: _Hz: Duration: _h o Test room ambient: _ C Voltage: V Insulation class (IEC 60085) tm o C tc o C ta o C Result Pass/Fail NOTE Tm = Measured temperature Tc = Corrected maximum temperature (t m + 40 – test room ambient) Ta = Maximum allowed temperature Tested by: _Date: Test equipment No (Table 2) Stt.010.Mssv.BKD002ac.email.ninhd.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj.dtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn.Stt.010.Mssv.BKD002ac.email.ninhddtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn Comments LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU Motor No and location C.vT.Bg.Jy.Lj.Tai lieu Luan vT.Bg.Jy.Lj van Luan an.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj Do an.Tai lieu Luan van Luan an Do an.Tai lieu Luan van Luan an Do an – 56 – TR 61010-3-043  IEC:2001(E) Form A.26 14.3 Overtemperature protection devices Component Type Result (note) Pass/Fail SR self-resetting (200 times) NSR = = non-self-resetting (10 times) NR non-resetting (1 time) = General comments: Tested by: _Date: Test equipment No (Table 2) Stt.010.Mssv.BKD002ac.email.ninhd.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj.dtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn.Stt.010.Mssv.BKD002ac.email.ninhddtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU NOTE Comments C.vT.Bg.Jy.Lj.Tai lieu Luan vT.Bg.Jy.Lj van Luan an.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj Do an.Tai lieu Luan van Luan an Do an.Tai lieu Luan van Luan an Do an TR 61010-3-043  IEC:2001(E) – 57 – Form A.27 4.4.2.6 Mains transformer 14.7.1 Short-circuit tests (for mains transformers) Type: _ Manufacturer: _ _ Tested in equipment Optional – or on bench Insulation class (IEC 60085) of the lowest rated winding: Winding identification Type of protector for winding (note 1) Current A Primary Secondary Winding temperature o C Primary (note 2) Secondary Tissue paper/cheesecloth OK? Voltage tests (Pass / Fail) (note 3) Primary to secondary Primary to core V _ V _ Secondary to secondary V _ Secondary to core V _ Result (Pass / Fail) NOTE Primary fuse NOTE PF / ( )A Secondary fuse SF / ( )A Overtemperature protection OP / ( )°C Impedance protection Z Indicate method of measurement TC R = = with thermocouple resistance method If resistance method is used, record resistance in cold and warm condition under "Comments" NOTE Record the voltage applied and the type of voltage (r.m.s./d.c./peak) and for results use NB = no breakdown or B = breakdown Comments: Tested by: _Date: Stt.010.Mssv.BKD002ac.email.ninhd.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj.dtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn.Stt.010.Mssv.BKD002ac.email.ninhddtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU Elapsed time C.vT.Bg.Jy.Lj.Tai lieu Luan vT.Bg.Jy.Lj van Luan an.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj Do an.Tai lieu Luan van Luan an Do an.Tai lieu Luan van Luan an Do an – 58 – TR 61010-3-043  IEC:2001(E) Test equipment No (Table 2) Form A.28 4.4.2.6 Mains transformer 14.7.2 Overload tests (for mains transformers) Type: _ Manufacturer: _ _ Tested in equipment Optional or on bench Insulation class (IEC 60085) of the lowest rated winding: Winding identification Elapsed time Current A Primary Secondary Winding temperature o C Primary (note 2) Secondary Tissue paper/cheesecloth OK? Voltage tests (note 3) Primary to secondary Primary to core (Pass / Fail) V _ V _ Secondary to secondary V _ Secondary to core V _ Result (Pass / Fail) NOTE Primary fuse NOTE PF / ( )A Secondary fuse SF / ( )A Overtemperature protection OP / ( ) C Impedance protection Z o Indicate method of measurement TC = with thermocouple R = resistance method If resistance method is used, record resistance in cold and warm condition under "Comments" NOTE Record the voltage applied and the type of voltage (r.m.s./d.c./peak) and for results use NB = no breakdown or B = breakdown Comments: Tested by: _Date: Test equipment No (Table 2) Stt.010.Mssv.BKD002ac.email.ninhd.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj.dtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn.Stt.010.Mssv.BKD002ac.email.ninhddtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU Type of protector for winding (note 1) C.vT.Bg.Jy.Lj.Tai lieu Luan vT.Bg.Jy.Lj van Luan an.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj Do an.Tai lieu Luan van Luan an Do an.Tai lieu Luan van Luan an Do an TR 61010-3-043  IEC:2001(E) – 59 – Form A.29 16.1 Current measuring circuits The test is performed with all types and models of current transformers without internal protection, and which are specified by the manufacturer for use with the equipment a) Current transformers Type/ Model current Test current A A RATED Interrupt Result Yes/No Pass/Fail Comments Test equipment No (Table 2) b) Range changing switches Maximum Type/Model RATED current of switch Cycling test Pass/Fail Tested by: _Date: _ Test equipment No (Table 2) Stt.010.Mssv.BKD002ac.email.ninhd.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj.dtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn.Stt.010.Mssv.BKD002ac.email.ninhddtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn Comments LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU Tested by: Date: _ C.vT.Bg.Jy.Lj.Tai lieu Luan vT.Bg.Jy.Lj van Luan an.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj Do an.Tai lieu Luan van Luan an Do an.Tai lieu Luan van Luan an Do an LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU Stt.010.Mssv.BKD002ac.email.ninhd.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj.dtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn.Stt.010.Mssv.BKD002ac.email.ninhddtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn C.vT.Bg.Jy.Lj.Tai lieu Luan vT.Bg.Jy.Lj van Luan an.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj Do an.Tai lieu Luan van Luan an Do an.Tai lieu Luan van Luan an Do an Standards Survey The IEC would like to offer you the best quality standards possible To make sure that we continue to meet your needs, your feedback is essential Would you please take a minute to answer the questions overleaf and fax them to us at +41 22 919 03 00 or mail them to the address below Thank you! Customer Service Centre (CSC) or Fax to: IEC/CSC at +41 22 919 03 00 Thank you for your contribution to the standards-making process Nicht frankieren Ne pas affranchir A Prioritaire Non affrancare No stamp required RÉPONSE PAYÉE SUISSE Customer Service Centre (CSC) International Electrotechnical Commission 3, rue de Varembé 1211 GENEVA 20 Switzerland Stt.010.Mssv.BKD002ac.email.ninhd.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj.dtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn.Stt.010.Mssv.BKD002ac.email.ninhddtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU International Electrotechnical Commission 3, rue de Varembé 1211 Genève 20 Switzerland C.vT.Bg.Jy.Lj.Tai lieu Luan vT.Bg.Jy.Lj van Luan an.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj Do an.Tai lieu Luan van Luan an Do an.Tai lieu Luan van Luan an Do an Q1 Please report on ONE STANDARD and ONE STANDARD ONLY Enter the exact number of the standard: (e.g 60601-1-1) Q6 standard is out of date R standard is incomplete R standard is too academic R standard is too superficial R title is misleading R I made the wrong choice R other Q2 Please tell us in what capacity(ies) you bought the standard (tick all that apply) I am the/a: Q3 Q7 I work for/in/as a: (tick all that apply) manufacturing R consultant R government R test/certification facility R public utility R education R military R other timeliness quality of writing technical contents logic of arrangement of contents tables, charts, graphs, figures other Q8 Q4 Q5 Q9 This standard meets my needs: (tick one) not at all nearly fairly well exactly R R R R I read/use the: (tick one) French text only English text only both English and French texts This standard will be used for: (tick all that apply) general reference R product research R product design/development R specifications R tenders R quality assessment R certification R technical documentation R thesis R manufacturing R other Please assess the standard in the following categories, using the numbers: (1) unacceptable, (2) below average, (3) average, (4) above average, (5) exceptional, (6) not applicable Stt.010.Mssv.BKD002ac.email.ninhd.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj.dtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn.Stt.010.Mssv.BKD002ac.email.ninhddtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn R R R Please share any comment on any aspect of the IEC that you would like us to know: LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU purchasing agent R librarian R researcher R design engineer R safety engineer R testing engineer R marketing specialist R other If you ticked NOT AT ALL in Question the reason is: (tick all that apply) C.vT.Bg.Jy.Lj.Tai lieu Luan vT.Bg.Jy.Lj van Luan an.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj Do an.Tai lieu Luan van Luan an Do an.Tai lieu Luan van Luan an Do an LICENSED TO MECON Limited - RANCHI/BANGALORE FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU Stt.010.Mssv.BKD002ac.email.ninhd.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj.dtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn.Stt.010.Mssv.BKD002ac.email.ninhddtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn C.vT.Bg.Jy.Lj.Tai lieu Luan vT.Bg.Jy.Lj van Luan an.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj Do an.Tai lieu Luan van Luan an Do an.Tai lieu Luan van Luan an Do an Stt.010.Mssv.BKD002ac.email.ninhd.vT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.LjvT.Bg.Jy.Lj.dtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn.Stt.010.Mssv.BKD002ac.email.ninhddtt@edu.gmail.com.vn.bkc19134.hmu.edu.vn