Toyota RAV4 1994 2000 body electrical hệ thống điện thân xe trên xe RAV4 đời 1994 2000

54 1K 0
Toyota RAV4 1994 2000 body electrical   hệ thống điện thân xe trên xe RAV4 đời 1994 2000

Đang tải... (xem toàn văn)

Tài liệu hạn chế xem trước, để xem đầy đủ mời bạn chọn Tải xuống

Thông tin tài liệu

HỆ THỐNG ĐIỆN THÂN XE TRÊN XE TOYOTA RAV4 ĐỜI 1994-2000

BE0J3−04 BE−10 −BODY ELECTRICAL IGNITION SWITCH AND KEY UNLOCK WARNING SWITCH 1996 RAV4 (RM447U) IGNITION SWITCH AND KEY UNLOCK WARNING SWITCH LOCATION N11771 1 8 2 3 4 657 BE0J4−04 Z10028 1 2 OFF ON N01923 N01924 N01925 −BODY ELECTRICAL IGNITION SWITCH AND KEY UNLOCK WARNING SWITCH BE−11 1996 RAV4 (RM447U) INSPECTION 1. INSPECT IGNITION SWITCH CONTINUITY Switch position Tester connection Specified condition LOCK − No continuity ACC 2 − 3 Continuity ON 2 − 3 − 4, 6 − 7 Continuity START 1−2−4, 6−7−8 Continuity If continuity is not as specified, replace the switch. 2. INSPECT KEY UNLOCK WARNING SWITCH CONTI- NUITY Switch position Tester connection Specified condition SW OFF (Key removed) − No continuity SW ON (Key set) 1 − 2 Continuity If continuity is not as specified, replace the switch. 3. Key Unlock Warning System: INSPECT INTEGRATION RELAY OPERATION (a) Connect the positive (+) lead from the battery to terminal A1. (b) Connect the negative (−) lead from the battery to termi- nals A5, A6 and A10. (c) Check the buzzer sounds. (d) Disconnect the negative (−) lead from the battery to termi- nals A6. (e) Check that the buzzer stops sounding. (f) Connect the negative (−) lead from the battery to termi- nals A6. (g) Disconnect the negative (−) lead from the battery to termi- nals A5. (h) Check that the buzzer stops sounding. If operation is not as specified, replace the relay. BE−12 −BODY ELECTRICAL IGNITION SWITCH AND KEY UNLOCK WARNING SWITCH 1996 RAV4 (RM447U) 4. INSPECT INTEGRATION RELAY CIRCUIT (See page BE−37) 5. INSPECT DOOR COURTESY SWITCH CONTINUITY (See Page BE−22) BE0J5−06 −BODY ELECTRICAL HEADLIGHT AND TAILLIGHT SYSTEM BE−13 1996 RAV4 (RM447U) HEADLIGHT AND TAILLIGHT SYSTEM LOCATION BE0J6−01 N17327 Light Control Switch Switch Body Wiper and Washer Switch Spiral Cable BE−14 −BODY ELECTRICAL HEADLIGHT AND TAILLIGHT SYSTEM 1996 RAV4 (RM447U) COMPONENTS BE1MW−01 Z17623 HEAD TAIL OFF Right Left Flash 8 7 17 16 14 13 Z13558 3 4 2 1 3 4 2 1 Z05657 3 21 3 2 1 5 5 −BODY ELECTRICAL HEADLIGHT AND TAILLIGHT SYSTEM BE−15 1996 RAV4 (RM447U) INSPECTION 1. INSPECT LIGHT CONTROL SWITCH CONTINUITY Switch position Tester connection Specified condition OFF − No continuity TAIL 14 − 16 Continuity HEAD 13 − 14 − 16 Continuity If continuity is not as specified, replace the switch. 2. INSPECT HEADLIGHT DIMMER SWITCH CONTINU- ITY Switch position Tester connection Specified condition Flash 7 − 8 − 16 Continuity Low beam 16 − 17 Continuity High beam 7 − 16 Continuity If continuity is not as specified, replace the switch. 3. INSPECT HEADLIGHT CONTROL RELAY CONTINU- ITY Condition Tester connection Specified condition Constant 3 − 4 Continuity Apply B+ between terminals 3 and 4. 1 − 2 Continuity If continuity is not as specified, replace the relay. 4. INSPECT TAILLIGHT CONTROL RELAY CONTINUITY Condition Tester connection Specified condition Constant 1 − 2 Continuity Apply B+ between terminals 1 and 2. 3 − 5 Continuity If continuity is not as specified, replace the relay. 5. Light−on Warning System: INSPECT INTEGRATION RELAY OPERATION (a) Connect the positive (+) lead from the battery to terminal 1 and 12, the negative (−) lead to terminals 10. (b) Check that the buzzer sounds when the negative (−) lead from the battery is connected to terminal 6. If operation is not as specified, replace the relay. 6. INSPECT DOOR COURTESY SWITCH CONTINU- ITY(See pageBE−22) BE1MX−01 N18226 Beam Angle Gauge (Vertical Direction) Beam is Upward Beam is Downward Front OK Bubble OK OK Z17543 Front Acceptable Range ”O” Reading Adjusting Screw B Beam Angle Gauge (Horizontal Direction) BE−16 −BODY ELECTRICAL HEADLIGHT AND TAILLIGHT SYSTEM 1996 RAV4 (RM447U) ADJUSTMENT 1. ADJUST HEADLIGHT AIM (a) Do the following before inspection. S Make sure that the body around the headlight is not deformed. S Park the vehicle on a level spot. S The driver gets into the driver’s seat and puts the vehicle in a state ready for driving (with a full tank). S Bounce the vehicle several times. (b) Adjust the headlight aim in vertical direction. If the bubble is outside the acceptable range of the beam angle gauge, adjust it by using adjusting screw A. (c) Adjust the headlight aim in horizontal direction. If ”0” mark is not within the acceptable range, adjust the ”0” reading to the ”0” mark using adjusting screw B. N18226 Beam Angle Gauge (Vertical Direction) Beam is Upward Beam is Downward Front OK Bubble OK OK Z17544 Beam Angle Gauge (Horizontal Direction) Front Acceptable Range ”O” Reading Adjusting Screw B Holder Assembly N18085 ”O” Reading Holer Assembly Adjusting Screw B N18086 ”O” Reading Pawl Temporary Pawl −BODY ELECTRICAL HEADLIGHT AND TAILLIGHT SYSTEM BE−17 1996 RAV4 (RM447U) 2. ADJUST HEADLIGHT AIM (a) Replace the headlight. (b) Do the following before inspection. S Make sure that the body around the headlight is not deformed. S Park the vehicle on a level spot. S The driver gets into the driver’s seat and puts the vehicle in a state ready for driving (with a full tank). S Bounce the vehicle several times. (c) Adjust the headlight aim in vertical direction. (1) Using adjusting screw A, adjustment the headlight aim to within the specifications. (2) Make sure that the gauge bubble is within the ac- ceptable range. HINT: If the gauge bubble is outside the acceptable range, check that the vehicle is parked on a level spot. Readjust the headlight aim after parking the vehicle on a level spot. (d) Adjust the headlight aim in horizontal direction. Using adjusting screw B, adjust the headlight aim to within the specifications. 3. HOW TO RESET LH AND RH AIMING INDICATORS (Unlocking method) HINT: These operations should be done only when the head adjust- ment of the headlight aim is necessary, for example in case the headlight aim ”0” mark deviates from the acceptable range when the headlight is reassembled after repair. (a) Turn the adjusting screw B to the right, and remove the holder assembly from the cylindrical part of the housing. (b) Unlock the holder assembly. N18087 ”O” Reading Temporary Pawl Temporary Pawl View A View A Z17544 Beam Angle Gauge (Horizontal Direction) Front Acceptable Range ”O” Reading Adjusting Screw B Holder Assembly BE−18 −BODY ELECTRICAL HEADLIGHT AND TAILLIGHT SYSTEM 1996 RAV4 (RM447U) (c) Insert the holder assembly, unlock in step (b), to the screw and housing again. HINT: When the assembly is inserted till the pawl for temporary set is hooded to the cross slit of the housing as shown in view A, set- ting is completed. (d) Turn the adjusting screw B to the left and adjust the LH and RH headlight aims. (e) Pull the holder assembly backwards and lock it. BE0J9−05 −BODY ELECTRICAL TURN SIGNAL AND HAZARD WARNING SYSTEM BE−19 1996 RAV4 (RM447U) TURN SIGNAL AND HAZARD WARNING SYSTEM LOCATION [...]... 1996 RAV4 (RM447U) HINT: If the heat wire is not broken, the voltmeter indicates 0 V at the positive (+) end of the heat wire but gradually increases to about 12 V as the meter probe moves to the other end BE−48 BODY ELECTRICAL − POWER WINDOW CONTROL SYSTEM POWER WINDOW CONTROL SYSTEM LOCATION 1996 RAV4 (RM447U) BE0JP−05 BE−49 BODY ELECTRICAL 1996 RAV4 (RM447U) − POWER WINDOW CONTROL SYSTEM BE−50 BODY. .. specified, replace the switch 2 INSPECT PARK/NEUTRAL POSITION SWITCH (See page DI−156, DI−218) BE−26 BODY ELECTRICAL − STOP LIGHT SYSTEM STOP LIGHT SYSTEM LOCATION 1996 RAV4 (RM447U) BE0JF−06 BE−27 BODY ELECTRICAL 2 1 − STOP LIGHT SYSTEM BE0JG−01 INSPECTION INSPECT STOP LIGHT SWITCH CONTINUITY Switch position 2 3 1996 RAV4 (RM447U) 4 Z05647 Tester connection Specified condition Switch pin free (Pedal depressed)... more than 140 per minute If operation is not as specified, replace the flasher BE−24 BODY ELECTRICAL − BACK−UP LIGHT SYSTEM BACK−UP LIGHT SYSTEM LOCATION 1996 RAV4 (RM447U) BE0JD−05 BE−25 BODY ELECTRICAL 2 − BACK−UP LIGHT SYSTEM BE0JE−02 INSPECTION 1 1 INSPECT BACK−UP LIGHT SWITCH CONTINUITY Switch position 1996 RAV4 (RM447U) 1−2 No continuity Push BE2682 Specified condition Free Push Free Tester... Using a fine tip brush, apply a small amount to the wire After a few minutes, remove the masking tape Do not repair the defogger wire for at least 24 hours BE−45 BODY ELECTRICAL LOCATION 1996 RAV4 (RM447U) − DEFOGGER SYSTEM BE0JM−06 BE−46 BODY ELECTRICAL − DEFOGGER SYSTEM BE275−01 INSPECTION 1 INSPECT DEFOGGER SWITCH CONTINUITY Switch position 3−5−8 Continuity 3−5 Continuity Illumination circuit 2−6 Continuity... depressed) 1−2 Continuity Switch pin pushed in (Pedal released) 4 3 1 3−4 No continuity If continuity is not as specified, replace the switch BE−28 BODY ELECTRICAL − WIPER AND WASHER SYSTEM WIPER AND WASHER SYSTEM LOCATION 1996 RAV4 (RM447U) BE0JH−06 BE−29 BODY ELECTRICAL Washer Washer − WIPER AND WASHER SYSTEM BE271−01 INSPECTION 1 INSPECT FRONT WIPER SWITCH CONTINUITY Switch position Tester connection... after the motor operates again If operation is not as specified, replace the motor 1 5 6 N05772 1996 RAV4 (RM447U) BE−32 BODY ELECTRICAL − WIPER AND WASHER SYSTEM 9 (a) INSPECT REAR WIPER MOTOR OPERATION Connect the positive (+) lead from the battery to terminal 4 and the negative (−) lead to the motor body, check that the motor operates If operation is not as specified, replace the motor 4 N11726 (b)... 1996 RAV4 (RM447U) BE−44 BODY ELECTRICAL − DEFOGGER SYSTEM DEFOGGER SYSTEM Repair Point ON−VEHICLE REPAIR Broken Wire Masking Tape BE0150 IF NECESSARY,REPAIR DEFOGGER WIRE (a) Clean the broken wire tips with grease, wax and silicone remover (b) Place the masking tape along both sides of the wire to be repaired (c) Thoroughly mix the repair agent (Dupont paste No 4817) (d) (e) (f) BE0151 1996 RAV4 (RM447U)... POWER MAIN RELAY CONTINUITY Condition 3 2 2 5 1 5 3 Z05657 1996 RAV4 (RM447U) Specified condition Constant 1 Tester connection 1−2 Continuity Apply B+ between terminals 1 and 2 3−5 Continuity If continuity is not as specified, replace the relay BE−64 BODY ELECTRICAL − POWER MIRROR CONTROL SYSTEM POWER MIRROR CONTROL SYSTEM LOCATION 1996 RAV4 (RM447U) BE0JV−06 ... the switch 7 2 17 INT time control switch position 16 N17244 FAST SLOW Voltage Approx 1 −3 sec Battery positive voltage 0 volt Approx 10 −15 sec Battery positive voltage 0 volt V03883 1996 RAV4 (RM447U) BE−30 BODY ELECTRICAL 4 − WIPER AND WASHER SYSTEM INSPECT REAR WIPER AND WASHER SWITCH CONTINUITY Switch position Tester connection Specified condition Washer 1 2 − 16 Continuity Wiper OFF − No continuity... 7 − 13 Continuity Z15858 Specified condition Passenger ’s Switch (Window unlock): Switch position UP 1−5 7 − 12 Continuity OFF 1 − 5 − 12 Continuity DOWN 1996 RAV4 (RM447U) Tester connection Specified condition 1 − 12 5−7 Continuity BE−51 BODY ELECTRICAL − POWER WINDOW CONTROL SYSTEM Passenger ’s Switch (Window lock): Switch position Tester connection UP 7 − 12 Continuity Specified condition OFF 5 − . flasher. BE0JD−05 BE−24 BODY ELECTRICAL BACK−UP LIGHT SYSTEM 1996 RAV4 (RM447U) BACK−UP LIGHT SYSTEM LOCATION BE2682 Push Free 2 1 BE0JE−02 BODY ELECTRICAL BACK−UP LIGHT SYSTEM BE−25 1996 RAV4 (RM447U) INSPECTION 1 DI−218) BE0JF−06 BE−26 BODY ELECTRICAL STOP LIGHT SYSTEM 1996 RAV4 (RM447U) STOP LIGHT SYSTEM LOCATION BE0JG−01 Z05647 1 2 4 3 1 4 2 3 BODY ELECTRICAL STOP LIGHT SYSTEM BE−27 1996 RAV4 (RM447U) INSPECTION INSPECT. Direction) BE−16 BODY ELECTRICAL HEADLIGHT AND TAILLIGHT SYSTEM 1996 RAV4 (RM447U) ADJUSTMENT 1. ADJUST HEADLIGHT AIM (a) Do the following before inspection. S Make sure that the body around the

Ngày đăng: 24/05/2014, 16:24

Từ khóa liên quan

Mục lục

  • BE10

  • BE11

  • be13

  • be14

  • be15

  • be16

  • be19

  • be20

  • be24

  • be25

  • be26

  • be27

  • be28

  • be29

  • be44

  • be45

  • be46

  • be48

  • be50

  • be64

  • be65

  • DESCRI BE−66

  • TROU BE−68

  • LOCA BE−80

  • REMO BE−81

  • INST BE−82

Tài liệu cùng người dùng

  • Đang cập nhật ...

Tài liệu liên quan