Infinitylab lc series site preparation checklist

Agilent InfinityLab LC Series Site Preparation Checklist Agilent Site Preparation InfinityLab Checklist LC Series Thank you for purchasing an Agilent instrument To get you started and to assure a successful and timely installation, please refer to this specification or set of requirements Correct site preparation is the key first step in ensuring that your instruments and software systems operate reliably over an extended lifetime This document is an information guide AND checklist prepared for you that outlines the supplies, consumables, space and utility requirements for your equipment Customer Responsibilities Make sure your site meets the following prior to the installation date using the checklist below For details, see specific sections within this document, including:  The necessary laboratory or bench space is available  The environmental conditions for the lab as well as laboratory gases, tubing  The power requirements related to the product (e.g number & location of electrical outlets)  The required operating supplies necessary for the product and installation  Please consult Other/Special Requirements section below for other product-specific information  If Agilent is delivering installation and familiarization services, users of the instrument should be present throughout these services; otherwise, they will miss important operational, maintenance and safety information Important Customer Information If you have questions or problems in providing anything described as Customer Responsibilities above, please contact your local Agilent or partner support/service organization for assistance prior to delivery In addition, Agilent and/or its partners reserve the right to reschedule the installation dependent upon the readiness of your laboratory Should your site not be ready for whatever reasons, please contact Agilent as soon as possible to re-arrange any services that have been purchased Other optional services such as additional training, operational qualification (OQ) and consultation for user-specific applications may also be provided at the time of installation when ordered with the system, but should be contracted separately Issued: 26-Sep-2016 Revision: 2.1 Copyright: 2016 Page of 13 Agilent Technologies Agilent InfinityLab LC Series Site Preparation Checklist Module List Module Instrument Description G7102A 1290 Infinity II Evaporative Light Scattering Detector G7104A 1290 Infinity II Flexible Pump G7110B 1260 Infinity II Isocratic Pump G7111A 1260 Infinity II Quaternary Pump VL G7111B 1260 Infinity II Quaternary Pump G7112B 1260 Infinity II Binary Pump G7114A 1260 Infinity II Variable Wavelength Detector G7114B 1290 Infinity II Variable Wavelength Detector G7115A 1260 Infinity II Diode Array Detector WR G7116A 1260 Infinity II Multicolumn Thermostat G7116B 1290 Infinity II Multicolumn Thermostat G7117A 1290 Infinity II DAD FS G7117B 1290 Infinity II DAD G7117C 1260 Infinity II Diode Array Detector HS G7120A 1290 Infinity II High Speed Pump G7121A 1260 Infinity II Fluorescence Detector G7121B 1260 Infinity II Infinity Fluorescence Detector Spectra G7122A 1260 Infinity II Degasser G7129A 1260 Infinity II Vialsampler G7129B 1290 Infinity II Vialsampler G7130A 1200 Infinity Integrated Column Compartment G7162A 1260 Infinity II Refractive Index Detector G7162B 1290 Infinity II Refractive Index Detector G7165A 1260 Infinity II Multiple Wavelength Detector G7167A 1260 Infinity II Multisampler G7167B 1290 Infinity II Multisampler G5654A 1260 Infinity II Bio-Inert Quaternary Pump G5668A 1260 Infinity II Bio-Inert Multisampler G1328B 1260 Infinity II Manual Injector G4208A 1200 Infinity Series Instant Pilot Issued: 26-Sep-2016 Revision: 2.1 Copyright: 2016 Page of 13 Agilent Technologies Agilent InfinityLab LC Series Site Preparation Checklist Dimensions and Weight The module dimensions and weight allow you to place the module on almost any desk or laboratory bench It needs an additional 2.5 cm (1.0 inches) of space on either side and approximately cm (3.1 inches) in the rear for air circulation and electric connections The ELSD needs an additional approximately 15 cm (5.9 inches) of space in the rear for air circulation and electric connections If the bench shall carry a complete HPLC system, make sure that the bench is designed to bear the weight of all modules The autosampler module especially with a sample cooler installed should be operated in a proper horizontal position Use a bubble level to check the leveling of the sampler Instrument Description Weight Height Depth Width kg lbs mm in mm in mm in G7102A 11 (non-cooled), 13 (cooled) 24.3 415 16.3 450 17.7 200 7.9 G7104A 16.1 35.5 180 7.1 436 17.2 396 15.6 G7110B 12.6 28 180 7.1 436 17.2 396 15.6 G7111A, G7111B, G5654A 14.5 32 180 7.1 436 17.2 396 15.6 G7112B 17.6 38.8 180 7.1 436 17.2 396 15.6 G7114A, G7114B 11 24.3 140 5.5 436 17.2 396 15.6 G7115A 12 26.5 140 5.5 436 17.2 396 15.6 G7116A, G7116B 12.5 27.6 160 6.3 436 17.2 435 (460 1) 17.1 (18.1 1) G7117A, G7117B, G7117C 11.5 25.4 140 5.5 436 17.2 396 15.6 G7120A 21 46.3 200 7.9 436 17.2 396 15.6 G7121A, G7121B 11.9 26.2 140 5.5 436 17.2 396 15.6 G7122A 16 80 3.1 436 17.2 396 15.6 G7129A, G7129B 16.2 with cooler add kg 35.7 with cooler add 13.2 lbs 324 12.6 468 18.4 396 15.6 G7130A 1.8 3.96 86.5 3.4 106.5 4.2 396 15.6 G7162A, G7162B 15 33 180 7.1 436 17.2 396 15.6 G7165A 12 26.5 140 5.5 436 17.2 396 15.6 G7167A, G7167B, G5668A