Tiêu chuẩn BS EN 124 là tiêu chuẩn châu Âu nói đến các quy định về yêu cầu kĩ thuật cho thiết kế. Đồng thời, nó còn được dùng để áp dụng phương pháp thử đối với nắp hố ga, song chắn rác bằng composite và gang. Bên cạnh đó, theo tiêu chuẩn quốc gia TCVN, bộ tiêu chuẩn EN 124 bao gồm 6 phần:Phần 1: Định nghĩa, phân loại, nguyên tắc thiết kế chung, các yêu cầu về tính năng và phương pháp thử nghiệm.Phần 2: Các quy định liên quan tới nắp hố ga, hố thu và song chắn rác bằng gang.Phần 3: Các quy định liên quan tới nắp hố ga, hố thu và song chắn rác bằng thép và hợp kim nhôm.Phần 4: Các quy định liên quan tới nắp hố ga, hố thu và song chắn rác bằng bê tông cốt thép.Phần 5: Các quy định liên quan tới nắp hố ga, hố thu và song chắn rác bằng vật liệu compozit.Phần 6: Các quy định liên quan tới nắp hố ga, hố thu và song chắn rác bằng chất dẻo: PP, PE và PVC.
6/19/2020 BÁO GIÁ NẮP HỐ GA BẰNG GANG MỚI NHẤT 2020 | GOAT Hiện tại, tiêu chuẩn BS EN 124 áp dụng cho nắp hố ga phân thành loại tải trọng sau: Minh họa tiêu chuẩn BS EN 124 A15 – Tải trọng 1,5 – Sử dụng nơi dành riêng cho người xe đạp B125 – Tải trọng 12,5 – Sử dụng vỉa hè, vùng dành cho người bộ, xe máy, bãi đỗ xe C250 – Tải trọng 25 – Sử dụng lề đường, cách vỉa hè phía đường tối đa 0.5m phía người 0.2m D400 – Tải trọng 40 tấn: Sử dụng lòng đường, bãi đỗ xe dành cho phương tiện giao thông đường naphoga.vn/bao-gia-nap-ho-ga-bang-gang/#Dieu_khoan_thanh_toan_Nap_ho_ga_bang_Gang 1/1 EN 124-1 EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM June 2015 ICS 93.080.30 Supersedes EN 124:1994 English Version FO Gully tops and manhole tops for vehicular and pedestrian areas Part 1: Definitions, classification, general principles of design, performance requirements and test methods Aufsätze und Abdeckungen für Verkehrsflächen - Teil 1: Definitionen, Klassifizierung, allgemeine Baugrundsätze, Leistungsanforderungen und Prüfverfahren Dispositifs de couronnement et de fermeture pour les zones de circulation utilisées par les piétons et les véhicules Partie : Définitions, classification, principes généraux de conception, exigences de performances et méthodes d'essai R This European Standard was approved by CEN on 12 March 2015 CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member U ST This European Standard exists in three official versions (English, French, German) A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom Y D EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels © 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members Ref No EN 124-1:2015 E EN 124-1:2015 (E) Contents Page Foreword Scope Normative references 3.1 3.2 Terms and definitions, symbols, units and abbreviated terms Terms and definitions Symbols and abbreviated terms 11 4.1 4.2 Classification 11 Basis of the classification 11 Classification in the context of intended use 11 5.1 5.2 5.3 Materials 13 General 13 Cover fillings 13 Frames in combination with concrete 13 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 6.10 6.11 6.12 6.13 6.14 6.15 6.16 6.17 6.18 Design requirements 13 Vents in covers 13 Clear opening of manhole tops for man entry 14 Depth of insertion 14 Clearance 14 Compatibility of seatings 15 Securing of the cover/grating within the frame 15 Handling of covers and gratings 16 Slot dimensions of gratings 16 Dirt pans and dirt buckets 17 Positioning of covers and gratings 18 Flatness of manhole covers and gratings 18 Concaveness of gratings 18 Surface conditions 18 Manhole tops with sealing features 18 Frame bearing area 18 Frame depth 18 Opening angle of hinged covers/gratings 19 Covers with fillings 19 7.1 7.2 7.3 7.4 7.5 Performance requirements 19 Appearance 19 Load bearing capacity 19 Permanent set 19 Skid resistance 20 Child safety 21 8.1 8.2 8.3 8.4 8.5 Testing 22 General 22 Permanent set (see 7.3) 22 Load bearing capacity (see 7.2) 22 Verification of design requirements 22 Child safety 24 Assessment and verification of constancy of performance (AVCP) 24 Y D U ST R FO EN 124-1:2015 (E) Annex A (normative) Permanent set test 25 A.1 Test Samples 25 A.2 Permanent set test load, (FP) 25 A.3 Apparatus 25 A.4 Procedure 26 Annex B (normative) Test of load bearing capacity 29 B.1 Test samples 29 B.2 Test load (FT) 29 FO B.3 Test procedure 29 B.4 Test report 29 Annex C (normative) Test to determine the unpolished skid resistance value (USRV) of manhole covers 30 General 30 C.2 Apparatus 30 C.3 Calibration of pendulum friction test equipment 30 C.4 Selection of test samples 30 C.5 Test procedure 30 R C.1 Annex D (normative) Tilt test 33 General 33 D.2 Test procedure 33 U ST D.1 Annex E (normative) Testing of securing of covers/gratings within the frame 36 E.1 General 36 E.2 Vertical pull-out test procedure 37 Annex F (informative) Recommendations for installation 41 General 41 F.2 Place of installation and selection of appropriate manhole tops and gully tops 41 F.3 Preparations before installation 41 F.4 Operative skill, training and installation equipment 41 F.5 Bedding and packing materials 42 F.6 Condition of supporting chamber 42 F.7 Fixing of manhole tops or gully tops 42 F.8 Post installation check and cleaning 42 Y D F.1 Annex G (informative) Explanations on testing of manhole tops with multiple covers and testing the skid resistance 44 G.1 Explanation to A.4 44 G.2 Explanation to 7.4.2 44 Bibliography 45 EN 124-1:2015 (E) Foreword This document (EN 124-1:2015) has been prepared by Technical Committee CEN/TC 165 “Wastewater engineering”, the secretariat of which is held by DIN This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2015 and conflicting national standards shall be withdrawn at the latest by March 2017 FO Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights Together with EN 124-2:2015, EN 124-3:2015, EN 124-4:2015, EN 124-5:2015 and EN 124-6:2015, this document supersedes EN 124:1994 This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association R EN 124, Gully tops and manhole tops for vehicular and pedestrian areas, consists of the following parts: Part 1: Definitions, classification, general principles of design, performance requirements and test methods; — Part 2: Gully tops and manhole tops made of cast iron; — Part 3: Gully tops and manhole tops made of steel or aluminium alloys; — Part 4: Gully tops and manhole tops made of steel reinforced concrete; — Part 5: Gully tops and manhole tops made of composite materials; — Part 6: Gully tops and manhole tops made of polypropylene (PP), polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC-U) U ST — EN 124-1 is not a harmonized standard but a supporting standard for the harmonized standards EN 124-2, EN 124-3, EN 124-4, EN 124-5 and EN 124-6 The main changes with respect to the previous edition are listed below: D the standard was split into parts, where Part contains general design and performance requirements and Parts to performance requirements for manhole tops and gully tops made of specific materials; b) definition for “securing feature” added; c) definition for “locking accessory” added; d) skid resistance test added; e) tilt test added; f) test of securing of covers/gratings within the frame added; g) evaluation of conformity changed to AVCP; h) recommendations for installation added Y a) EN 124-1:2015 (E) According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom R FO Y D U ST EN 124-1:2015 (E) Scope This European Standard is applicable to manhole tops and gully tops with a clear opening up to and including 000 mm for covering gullies, manholes and inspection chambers installed in areas subjected to pedestrian and/or vehicular traffic It specifies definitions, classification, general principles of design, performance requirements and test methods for gully tops and manhole tops according to: EN 124-2, for gully tops and manhole tops made of cast iron; — EN 124-3, for gully tops and manhole tops made of steel or aluminium alloys; — EN 124-4, for gully tops and manhole tops made of steel reinforced concrete; — EN 124-5, for gully tops and manhole tops made of composite materials; — EN 124-6, for gully tops and manhole tops made of polypropylene (PP), polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC-U) FO — Part is only applicable in combination with at least one of the standards EN 124-2, EN 124-3, EN 124-4, EN 124-5 and EN 124-6 each of which has this Part as an integral part R This European Standard is not applicable to: gratings/covers as part of prefabricated drainage channels according to EN 1433, — floor and roof gullies in buildings which are specified in EN 1253 (all parts), — surface boxes Normative references U ST — The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies EN 124-2:2015, Gully tops and manhole tops for vehicular and pedestrian areas — Part 2: Gully tops and manhole tops made of cast iron D EN 124-3:2015, Gully tops and manhole tops for vehicular and pedestrian areas — Part 3: Gully tops and manhole tops made of steel or aluminium alloys EN 124-4:2015, Gully tops and manhole tops for vehicular and pedestrian areas — Part 4: Gully tops and manhole tops made of steel reinforced concrete Y EN 124-5:2015, Gully tops and manhole tops for vehicular and pedestrian areas — Part 5: Gully tops and manhole tops made of composite materials EN 124-6:2015, Gully tops and manhole tops for vehicular and pedestrian areas — Part 6: Gully tops and manhole tops made of polypropylene (PP), polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC-U) EN 206:2013, Concrete — Specification, performance, production and conformity EN 13036-4, Road and airfield surface characteristics — Test methods — Part 4: Method for measurement of slip/skid resistance of a surface: The pendulum test EN 124-1:2015 (E) EN ISO 868, Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) (ISO 868) EN ISO 7500-1:2004, Metallic materials — Verification of static uniaxial testing machines — Part 1: Tension/compression testing machines — Verification and calibration of the force-measuring system (ISO 7500-1:2004) Terms and definitions, symbols, units and abbreviated terms For the purposes of this document, the following terms and definitions apply Terms and definitions FO 3.1 3.1.1 manhole structure with a removable cover constructed on a drain or sewer to permit entry by personnel [SOURCE: EN 16323:2014, 2.2.4.15] R 3.1.2 inspection chamber structure with a removable cover constructed on a drain or sewer that permits the introduction of cleaning and inspection equipment from surface level, but does not provide access for personnel [SOURCE: EN 16323:2014, 2.2.4.13] U ST 3.1.3 gully assembly to receive water for discharge into a drainage system 3.1.4 gully top upper part of a gully consisting of a frame and grating with or without cover 3.1.5 manhole top upper part of a manhole or inspection chamber consisting of a frame and cover and/or grating 3.1.7 frame depth distance between the top surface and the bottom surface of the frame Y D 3.1.6 frame part of a gully top or manhole top which receives and supports a grating and/or a cover 3.1.8 grating movable part(s) or opening within a manhole top or a gully top which permit(s) the passage of water through itself into the gully or manhole 3.1.9 cover movable part(s) of a manhole top or a gully top which covers the manhole or gully opening EN 124-1:2015 (E) 3.1.10 element frame or cover or grating of a manhole top or gully top Note to entry: Hinges, locking accessories and other accessories are not elements 3.1.11 vent opening in the cover of a manhole top to provide ventilation FO 3.1.12 dirt bucket removable component of a gully top which collects debris 3.1.13 dirt pan removable component of manhole top which collects debris R 3.1.14 seating surface on which the grating or the cover rests in the frame 3.1.15 depth of insertion A distance between the top of the frame and the bottom of the cover or grating adjacent to the seating Examples are given in Figure The depth of insertion is expressed in millimetres (mm) U ST Note to entry: a) Example 1: A for non-stepped covers/gratings b) Example 2: A for stepped covers/gratings when b ≤ a D Y c) Example 3: A for stepped covers/gratings when b > a Figure — Examples for determination of depth of insertion 3.1.16 total clearance Σa sum of the maximum individual clearances between adjacent elements of the frame and grating/cover Note to entry: Examples are shown in Figure a), Figure b) and Figure c) Note to entry: The total clearance is expressed in millimetres (mm) EN 124-1:2015 (E) Σa = al + ar Σa = al + ac1 + ac2 + ar a) Example Σa = al + ac + ar b) Example c) Example Key FO al clearance left ac ar clearance centre clearance right Figure — Examples for the determination of total clearance 3.1.17 frame bearing area Ab surface of the underside of a frame which rests upon the supporting structure R Note to entry: The bearing area is expressed in square millimetres (mm ) 3.1.18 clear opening CO diameter of the largest circle that can be inscribed in the clear area (3.1.19) of the frame U ST Note to entry: Examples are shown in Figures a) to f) Note to entry: The clear opening is expressed in millimetres (mm) a) Example b) Example c) Example Y D d) Example fixed bars e) Example f) Example Figure — Examples of clear opening BS EN 124-6:2015 EN 124-6:2015 (E) Annex A (normative) Characteristics of glass fibres used for reinforcement of PP polymer Glass fibres used for reinforcement of PP polymer shall fulfil the requirements in accordance with EN 16245-3:2013 and Table A.1 Table A.1 — Specification of glass fibres used for reinforcement of PP Characteristics Value/Unit Method Type of glass fibres Chopped fibres EN 16245–3 Length of glass fibres mm to mm ISO 1888 Diameter of glass fibres µm to 24 µm ISO 1888 Coating Chemical coating to ensure resin compatibility to materials listed in Table EN 16245–3 Density 2,45 g/cm to 2,58 g/cm E-Modulus 70 to 90 GPa EN ISO 9163 Elongation at break 40 mm EN 124–1:2015, 7.4.4, determined acc to the requirement clause and expressed as — “NPD” for ≤ 40 mm or — method or value for > 40 mm Durability of: — load bearing capacity against mechanical failure EN 124–6:2015, 5.2.5 — securing against mechanical failure EN 124–6:2015, 5.2.5 — skid resistance against loss of grip EN 124–6:2015, 5.2.5 — effectiveness of child safety EN 124–6:2015, 5.2.5.5 Dangerous substances EN 124–6: 2015, 5.2.6 – expressed as “Pass” for the material and the test method applied – expressed as “Pass” for the material and the test method applied – expressed as “Pass” for the “raised pattern” or the declared value of USRV, if applicable – Expressed as “Pass” after visual inspection of the performance in accordance with EN 124–1:2015, 6.6 – see 5.2.6 The declaration of the product performance related to certain essential characteristics is not required in those Member States (MS) where there are no regulatory requirements on these essential characteristics for the intended use of the product In this case, manufacturers placing their products on the market of these MS are not obliged to determine nor declare the performance of their products with regard to these essential characteristics and the option “No performance determined” (NPD) in the information accompanying the CE marking and in the declaration of performance (see ZA.3) may be used for those essential characteristics 30 BS EN 124-6:2015 EN 124-6:2015 (E) ZA.2 Procedures for AVCP of gully tops and manhole tops made of PP, PE or PVC-U) ZA.2.1 Systems of AVCP The AVCP systems of gully tops and manhole tops indicated in Table ZA.1 established by EC Decision 97/464/EC of 1997-06-27 (see OJEU L 198 of 1997-07-25), as amended by 2004/663/EC of 2004-09-20 (see OJEU L 302 of 2004-09-29), is shown in Table ZA.2 for the indicated intended use(s) and relevant level(s) or class(es) of performance Table ZA.2 — Systems of AVCP Product Intended use Level(s) or class(es) of performance AVCP systems Manhole tops and gully tops For use in vehicular and pedestrian areas No regulatory classes- For use(s) when subject regulations on reaction to fire A1*, A2*, B*, C* ––––– A1**, A2**, B**, C**, D, E ––––– (A1 to E)***, F –––3 –––4 to System 1: See Regulation (EU) No 305/2011 (CPR) Annex V, 1.2 System 3: See Regulation (EU) No 305/2011 (CPR) Annex V, 1.4 System 4: See Regulation (EU) No 305/2011 (CPR) Annex V, 1.5 * Products/materials for which a clearly identifiable stage in the production process results in an improvement of the reaction to fire classification (e.g an addition of fire retardants or a limiting of organic material) ** Products/materials not covered by footnote (*) *** Products/materials that not require to be tested for reaction to fire (e.g products/materials of class A1 according to the Decision 96/603/EC, as amended) The AVCP of the gully tops and manhole tops made of PP, PE or PVC-U in Table ZA.1 shall be according to the AVCP procedures indicated in Table ZA.3 resulting from application of the clauses of this or other European Standard indicated therein The content of tasks of the notified body shall be limited to those essential characteristics as provided for, if any, in Annex III of the relevant mandate and to those that the manufacturer intends to declare 31 BS EN 124-6:2015 EN 124-6:2015 (E) Table ZA.3 — Assignment of AVCP tasks for gully tops and manhole tops made of polypropylene (PP), polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC-U) under system 1, system and system Tasks Tasks for the manufacturer Factory production control (FPC) Content of the task — — Further testing of samples taken at the factory according to the prescribed test plan — — Tasks for the notified certification body Determination of the product-type on the basis of type testing (based on sampling carried out by the manufacturer), type calculation, tabulated values or descriptive documentation of the product — Initial inspection of manufacturing plant and of FPC — — — Continuous surveillance, assessment and evaluation of FPC — — AVCP clauses to apply Parameters related to essential characteristics of Table ZA.1 relevant for the intended use for which performance is declared (except for reaction to fire) Reaction to fire only relevant for use(s) when subject to regulations on reaction to fire (for classes B*, C*, D, E or F), if applicable 7.3.1, 7.3.2, 7.3.3, 7.3.5, 7.3.6 Essential characteristics of Table ZA.1 relevant for the intended use for which performance is declared (except for reaction to fire) Reaction to fire only relevant for use(s) when subject to regulations on reaction to fire (for classes B*, C*), if applicable 7.3.4 Parameters related to essential characteristics of Table ZA.1 relevant for the intended use for which performance is declared (except for reaction to fire) Reaction to fire only relevant for use(s) when subject to regulations on reaction to fire (for classes B*, C*, D, E), if applicable 7.2 Parameters related to essential characteristics of Table ZA.1, relevant for the intended use which is declared Documentation of the FPC (except for reaction to fire) Reaction to fire only relevant for use(s) when subject to regulations on reaction to fire (for classes B*, C*), if applicable 7.3.4 Parameters related to essential characteristics of Table ZA.1, relevant for the intended use which is declared Documentation of FPC (except for reaction to fire) Reaction to fire only relevant for use(s) when subject to regulations on reaction to fire (for classes B*, C*) 7.3.5 * Products/materials for which a clearly identifiable stage in the production process results in an improvement of the reaction to fire classification (e.g an addition of fire retardants or a limiting of organic material) 32 BS EN 124-6:2015 EN 124-6:2015 (E) ZA.2.2 Declaration of performance (DoP) ZA.2.2.1 General The manufacturer draws up the DoP and affixes the CE marking on the basis of the different AVCP systems set out in Annex V of the Regulation (EU) No 305/2011: — the factory production control and further testing of samples taken at the factory according to the prescribed test plan, carried out by the manufacturer; and — the certificate of constancy of performance issued by the notified product certification body on the basis of determination of the product type on the basis of type testing (including sampling), type calculation, tabulated values or descriptive documentation of the product; initial inspection of the manufacturing plant and of factory production control and continuous surveillance, assessment and evaluation of factory production control ZA.2.2.2 Content The model of the DoP is provided in Annex III of the Regulation (EU) No 305/2011 According to this Regulation, the DoP shall contain, in particular, the following information: — the reference of the product-type for which the declaration of performance has been drawn up; — the AVCP system or systems of the construction product, as set out in Annex V of the CPR; — the reference number and date of issue of the harmonized standard which has been used for the assessment of each essential characteristic; — where applicable, the reference number of the Specific Technical Documentation used and the requirements with which the manufacturer claims the product complies The DoP shall in addition contain: a) the intended use or uses for the construction product, in accordance with the applicable harmonized technical specification; b) the list of essential characteristics, as determined in the harmonized technical specification for the declared intended use or uses; c) the performance of at least one of the essential characteristics of the construction product, relevant for the declared intended use or uses; d) where applicable, the performance of the construction product, by levels or classes, or in a description, if necessary based on a calculation in relation to its essential characteristics determined in accordance with the Commission determination regarding those essential characteristics for which the manufacturer shall declare the performance of the product when it is placed on the market or the Commission determination regarding threshold levels for the performance in relation to the essential characteristics to be declared; e) the performance of those essential characteristics of the construction product which are related to the intended use or uses, taking into consideration the provisions in relation to the intended use or uses where the manufacturer intends the product to be made available on the market; f) for the listed essential characteristics for which no performance is declared, the letters “NPD” (No Performance Determined) Regarding the supply of the DoP, Article of the Regulation (EU) No 305/2011 applies 33 BS EN 124-6:2015 EN 124-6:2015 (E) The information referred to in Article 31 or, as the case may be, in Article 33 of Regulation (EC) No 1907/2006, (REACH) shall be provided together with the DoP ZA.2.2.3 Example of DoP The following gives an example of a filled-in DoP for a manhole top made of polypropylene (PP) DECLARATION OF PERFORMANCE No 00001 – CPR – 2015/05/12 Unique identification code of the product-type: Manhole Top EN 124-6 — A 15 – PP – 6/6 – 400 – F – RP Intended use or uses: For covering of openings of inspection chambers in areas subjected to pedestrian traffic Manufacturer: AnyCo SA, PO Box 21 B-1050 Brussels, Belgium Tel.:+32987654321 Fax: +32123456789 e-mail: anyco.sa@provider.be Authorized representative: Anyone Ltd Flower Str 24 West Hamfordshire UK-589645 United Kingdom Tel +44987654321 Fax: +44123456789 e-mail: mailto:anyone.ltd@provider.uk System of AVCP: System for the intended use under item Harmonized standard: EN 124-6 Notified product certification body (name) No 5678, performed the determination of the product-type on the basis of type testing, the initial inspection of the manufacturing plant and of factory production control and the continuous surveillance, assessment and evaluation of factory production control under system and issued the certificate of constancy of performance of the product Declared performance Essential characteristics Performance Reaction to fire E Harmonized technical specification EN 124–6: 2015 Load-bearing capacity, as: — frame bearing area 34 Pb ≤ 7,5 N/mm BS EN 124-6:2015 EN 124-6:2015 (E) — load-bearing capacity 15 kN — permanent set ≤ mm Securing of covers Securing feature Child safety Locking accessory Skid resistance Raised pattern Durability of load bearing capacity against — mechanical failure Pass Durability of securing, against — unintended lifting Pass Durability of skid resistance, against: — loss of grip Pass Durability of effectiveness of child safety Pass Dangerous substances NPD Appropriate Technical Documentation and/or Specific Technical Documentation, if appropriate (see Articles 36 to 38 of Regulation (EU) No 305/2011) - not appropriate The performance of the product identified above is in conformity with the set of declared performance/s This declaration of performance is issued in accordance with regulation (EU) No 305/2011 under the sole responsibility of the manufacturer identified above Signed for and on behalf of the manufacturer by: (name) ……………………………………………………………………………………………………………………… at (place) ………………………………… ……… on (date of issue) …………………………………………… (signature) ………………………………………………………………………………………………….……………… ZA.3 CE marking and labelling The CE marking symbol shall be in accordance with the general principles set out in Article 30 of Regulation (EC) No 765/2008 and shall be affixed visibly, legibly and indelibly — to the manhole top or gully top The CE marking and the accompanying information shall be placed on a label attached to it, or on the packaging or on the accompanying documents The CE marking shall be followed by: a) the last two digits of the year in which it was first affixed; b) the name and the registered address of the manufacturer, or the identifying mark allowing identification of the name and address of the manufacturer easily and without any ambiguity; c) the unique identification code of the product-type; d) the reference number of the declaration of performance (see example of DOP); 35 BS EN 124-6:2015 EN 124-6:2015 (E) e) the level or class of the performance declared; f) the dated reference to the harmonized technical specification applied; g) the identification number of the notified body; h) the intended use as laid down in the harmonized technical specification applied The CE marking shall be affixed before the construction product is placed on the market It may be followed by a pictogram or any other mark notably indicating a special risk or use Figure ZA.1, gives an example of such complete CE marking given in the commercial documents, accompanying gully top or manhole top 36 BS EN 124-6:2015 EN 124-6:2015 (E) “CE” marking consisting of the “CE”- symbol 01234 Identification number of the notified certification body AnyCo Ltd Name and registered address or identifying mark of the manufacturer Last two digits of the year in which the marking was first affixed Reference number of the DoP 15 No 00001 – CPR – 2015/05/12 EN 124-6:2015 Manhole top A 15 – PP – 6/6 – 400 – F – RP Intended use of the product as laid down in the European Standard applied for use in areas for pedestrian traffic Reaction to fire Number of the European Standard, and the year of its publication Unique identification code of the product type Levels or classes of the performance E Load-bearing capacity, as: — frame bearing area Pb ≤ 7,5 N/mm — load-bearing capacity 15 kN — permanent set ≤ mm Securing of covers as Securing feature Child safety Locking accessory Skid resistance Raised pattern Durability of load bearing capacity against: — mechanical failure Pass Durability of securing against — unintended lifting Pass Durability of skid resistance against: — loss of grip Pass Dangerous substances NPD Figure ZA.1 — Example for CE marking given in the commercial documents, accompanying manhole top, class A 15, made of PP, secured by a securing feature 37 BS EN 124-6:2015 EN 124-6:2015 (E) Bibliography [1] EN 607, Eaves gutters and fittings made of PVC-U — Definitions, requirements and testing [2] EN 1253 (all parts), Gullies for buildings [3] EN 1433, Drainage channels for vehicular and pedestrian areas — Classification, design and testing requirements, marking and evaluation of conformity [4] EN 12201-1, Plastics piping systems for water supply, and for drainage and sewerage under pressure — Polyethylene (PE) — Part 1: General [5] EN ISO 9001, Quality management systems — Requirements (ISO 9001) 38 This page deliberately left blank NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW British Standards Institution (BSI) BSI is the national body responsible for preparing British Standards and other standards-related publications, information and services BSI is incorporated by Royal Charter British Standards and other standardization products are published by BSI Standards Limited About us Revisions We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions Our British Standards and other publications are updated by amendment or revision The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process Organizations of all sizes and across all sectors choose standards to help them achieve their goals Information on standards We can provide you with the knowledge that your organization needs to succeed Find out more about British Standards by visiting our website at bsigroup.com/standards or contacting our Customer Services team or Knowledge Centre Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at bsigroup.com/shop, where hard copies can also be purchased If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team Subscriptions Our range of subscription services are designed to make using standards easier for you For further information on our subscription products go to bsigroup.com/subscriptions With British Standards Online (BSOL) you’ll have instant access to over 55,000 British and adopted European and international standards from your desktop It’s available 24/7 and is refreshed daily so you’ll always be up to date You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member PLUS is an updating service exclusive to BSI Subscribing Members You will automatically receive the latest hard copy of your standards when they’re revised or replaced To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit bsigroup.com/shop With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet Licences can cover as few or as many users as you wish With updates supplied as soon as they’re available, you can be sure your documentation is current For further information, email bsmusales@bsigroup.com BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK We continually improve the quality of our products and services to benefit your business If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre Copyright All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means – electronic, photocopying, recording or otherwise – without prior written permission from BSI Details and advice can be obtained from the Copyright & Licensing Department Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): orders@bsigroup.com Email (enquiries): cservices@bsigroup.com Subscriptions Tel: +44 845 086 9001 Email: subscriptions@bsigroup.com Knowledge Centre Tel: +44 20 8996 7004 Email: knowledgecentre@bsigroup.com Copyright & Licensing Tel: +44 20 8996 7070 Email: copyright@bsigroup.com