IEC 61753 086 6 Edition 1 0 2010 12 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconnecting devices and passive components – Performance standard – Part 086 6 Non connectorized single[.]
® Edition 1.0 2010-12 INTERNATIONAL STANDARD NORME INTERNATIONALE colour inside Fibre optic interconnecting devices and passive components – Performance standard – Part 086-6: Non-connectorized single-mode bidirectional 490 / 550 nm downstream and 310 nm upstream WWDM devices for category O – Uncontrolled environment IEC 61753-086-6:2010 Dispositifs d'interconnexion et composants passifs fibres optiques – Norme de performance – Partie 086-6: Dispositifs WWDM unimodaux non connectorisés bidirectionnels 490 / 550 nm en voie descendante et 310 nm en voie montante pour la catégorie O – Environnement non contrôlé Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-28-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe IEC 61753-086-6 All rights reserved Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IEC's member National Committee in the country of the requester If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information Droits de reproduction réservés Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence IEC Central Office 3, rue de Varembé CH-1211 Geneva 20 Switzerland Email: inmail@iec.ch W eb: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies About IEC publications The technical content of IEC publications is kept under constant review by the IEC Please make sure that you have the latest edition, a corrigenda or an amendment might have been published § Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…) It also gives information on projects, withdrawn and replaced publications § IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications Just Published details twice a month all new publications released Available on-line and also by email § Electropedia: www.electropedia.org The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages Also known as the International Electrotechnical Vocabulary online § Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csc@iec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des normes internationales pour tout ce qui a trait l'électricité, l'électronique et aux technologies apparentées A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu Veuillez vous assurer que vous possédez l’édition la plus récente, un corrigendum ou amendement peut avoir été publié § Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence, texte, comité d’études,…) Il donne aussi des informations sur les projets et les publications retirées ou remplacées § Just Published CEI: www.iec.ch/online_news/justpub Restez informé sur les nouvelles publications de la CEI Just Published détaille deux fois par mois les nouvelles publications parues Disponible en-ligne et aussi par email § Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes électroniques et électriques Il contient plus de 20 000 termes et dộfinitions en anglais et en franỗais, ainsi que les termes équivalents dans les langues additionnelles Egalement appelé Vocabulaire Electrotechnique International en ligne § Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csc@iec.ch Tél.: +41 22 919 02 11 Fax: +41 22 919 03 00 Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-28-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright © 2010 IEC, Geneva, Switzerland ® Edition 1.0 2010-12 INTERNATIONAL STANDARD NORME INTERNATIONALE colour inside Fibre optic interconnecting devices and passive components – Performance standard – Part 086-6: Non-connectorized single-mode bidirectional 490 / 550 nm downstream and 310 nm upstream WWDM devices for category O – Uncontrolled environment Dispositifs d'interconnexion et composants passifs fibres optiques – Norme de performance – Partie 086-6: Dispositifs WWDM unimodaux non connectorisés bidirectionnels 490 / 550 nm en voie descendante et 310 nm en voie montante pour la catégorie O – Environnement non contrôlé INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE PRICE CODE CODE PRIX ICS 33.180.20 ® Registered trademark of the International Electrotechnical Commission Marque déposée de la Commission Electrotechnique Internationale P ISBN 978-2-88912-299-8 Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-28-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe IEC 61753-086-6 61753-086-6 Ó IEC:2010 CONTENTS FOREWORD Scope Normative references Test Test report Performance requirements 5.1 5.2 5.3 5.4 Annex A Reference components Dimensions Sample size, sequencing and grouping Test details and requirements (normative) Sample size, sequencing and grouping 11 Annex B (informative) General information for 490 / 550 nm downstream and 310 nm upstream PON WWDM device 12 Bibliography 14 Figure B.1 – Example of 490 / 550 nm downstream and 310 nm upstream WWDM at central office and customer side – Separate video detection inside the ONU 12 Figure B.2 – Example of 490 / 550 nm downstream and 310 nm upstream WWDM at central office side – Integrated video detection inside the ONU 13 Table – Test details and requirements Table A.1 – Sample size and sequencing of tests 11 Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-28-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe –2– –3– INTERNATIONAL ELECTROTECHNICAL COMMISSION FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS – PERFORMANCE STANDARD – Part 086-6: Non-connectorized single-mode bidirectional 490 / 550 nm downstream and 310 nm upstream WWDM devices for category O – Uncontrolled environment FOREWORD 1) The International Electrotechnic al Commission (IEC) is a worldwide organization for standardization c omprising all national electrotechnical committees (IEC National Committees) The object of IEC is to promot e international co-operation on all questions conc erning standardization in the electrical and electronic fields To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referr ed to as “IEC Publication(s)”) Their preparation is entrusted to technic al c ommittees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work International, governmental and nongovernmental organizations liaising with the IEC also participate in this preparation IEC c ollaborates clos el y with the International Organization for Standardization (ISO) in accordance with conditions determined b y agreement between the two organizations 2) The formal decisions or agr eements of IEC on technic al matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National C ommittees 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that s ense W hile all reas onable efforts are made to ensure that the technic al c ontent of IEC Publications is accurate, IEC c annot be held responsible for the way in which they are us ed or for an y misinterpr etation by any end us er 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC P ublications transparently to the maximum extent possible in their national and regional publications Any divergenc e between any IEC Publication and the corr esponding national or regional public ation shall be clearly indicated in the latter 5) IEC itself does not provide any attestation of conformity Independent certification bodies provide conformit y assessment services and, in s ome areas, access to IEC marks of conformity IEC is not responsible for an y services carried out by independent certification bodies 6) All users should ensure that they have the latest edition of this publication 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts an d members of its technical c ommittees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expens es arising out of the publication, use of, or relianc e upon, this IEC Publication or any other IEC Publications 8) Attention is drawn to the Normative ref erences cited in this publication Use of the ref erenced publications is indispens able f or the corr ect application of this publication 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights IEC shall not be held responsible for identifying any or all such patent rights International Standard IEC 61753-086-6 has been prepared by subcommittee 86B: Fibre optic interconnecting devices and passive components, of IEC technical committee 86: Fibre optics The text of this standard is based on the following documents: FDIS Report on voting 86B/3094/FDIS 86B/3132/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-28-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe 61753-086-6 Ó IEC:2010 This publication has been drafted in accordance with the ISO/IEC Directives, Part The list of all parts in the IEC 61753 series, under the general title Fibre optic interconnecting devices and passive components performance standards, can be found on the IEC website The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to the specific publication At this date, the publication will be • • • • reconfirmed, withdrawn, replaced by a revised edition, or amended IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents Users should therefore print this document using a colour printer NOTICE This document contains material that is Copyright ("Telcordia") All rights reserved © 2006, Telcordia Technologies, Inc The reader is advised that this IEC document and Telcordia source(s) may differ, and the context and use of said material in this IEC document may differ from that of Telcordia TELCORDIA MAKES NO REPRESENTATION OR WARRANTY, EXPRESS OR IMPLIED, WITH RESPECT TO THE SUFFICIENCY, ACCURACY, OR UTILITY OF ANY INFORMATION OR OPINION CONTAINED HEREIN ANY USE OF OR RELIANCE UPON SAID INFORMATION OR OPINION IS AT THE RISK OF THE USER TELCORDIA SHALL NOT BE LIABLE FOR ANY DAMAGE OR INJURY INCURRED BY ANY PERSON ARISING OUT OF THE SUFFICIENCY, ACCURACY, OR UTILITY OF ANY INFORMATION OR OPINION CONTAINED HEREIN Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-28-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe 61753-086-6 Ó IEC:2010 –4– –5– FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS – PERFORMANCE STANDARD – Part 086-6: Non-connectorized single-mode bidirectional 490 / 550 nm downstream and 310 nm upstream WWDM devices for category O – Uncontrolled environment Scope This part of IEC 61753 contains the minimum initial performance, test and measurement requirements and severities which a fibre optic pigtailed 490 / 550 nm downstream and 310 nm upstream wide wavelength division multiplexing (WWDM) passive optical network (PON) device must satisfy in order to be categorized as meeting the requirements of category O (uncontrolled environment), as defined in Annex A of IEC 61753-1:2007 Annex B of this standard provides information concerning the function of the 490 / 550 nm downstream and 310 nm upstream WWDM Normative references The following referenced documents are indispensable for the application of this document For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies IEC 60793-2-50, Optical fibre cables – Part 2-50: Indoor cables – Family specification for simplex and duplex cables for use in terminated cable assemblies IEC 61300-2-1, Fibre optic interconnecting devices and passive components – Basic test and measurement procedures – Part 2-1: Tests – Vibration (sinusoidal) IEC 61300-2-4, Fibre optic interconnecting devices and passive components – Basic test and measurement procedures – Part 2-4: Tests – Fibre/cable retention IEC 61300-2-5, Fibre optic interconnecting devices and passive components – Basic test and measurement procedures – Part 2-5: Tests – Torsion IEC 61300-2-9, Fibre optic interconnecting devices and passive components – Basic test and measurement procedures – Part 2-9: Tests – Shock IEC 61300-2-14, Fibre optic interconnecting devices and passive components – Basic test and measurement procedures – Part 2-14: Tests – Optical power handling and damage threshold characterization IEC 61300-2-19, Fibre optic interconnecting devices and passive components – Basic test and measurement procedures – Part 2-19: Tests – Damp heat (steady state) IEC 61300-2-22, Fibre optic interconnecting devices and passive components – Basic test and measurement procedures – Part 2-22: Tests – Change of temperature IEC 61300-2-42, Fibre optic interconnecting devices and passive components – Basic test and measurement procedures – Part 2-42: Tests – Static side load for connectors Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-28-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe 61753-086-6 Ó IEC:2010 61753-086-6 Ó IEC:2010 IEC 61300-2-44, Fibre optic interconnecting devices and passive components – Basic test and measurement procedures – Part 2-44: Tests – Flexing of the strain relief of fibre optic devices IEC 61300-2-48, Fibre optic interconnecting devices and passive components – Basic test and measurement procedures – Part 2-48: Tests – Temperature-humidity cycling IEC 61300-3-2, Fibre optic interconnecting devices and passive components – Basic test and measurement procedures – Part 3-2: Examinations and measurements – Polarization dependent loss in a single-mode fibre optic device IEC 61300-3-6, Fibre optic interconnecting devices and passive components – Basic test and measurement procedures – Part 3-6: Examinations and measurements – Return loss IEC 61300-3-7, Fibre optic interconnecting devices and passive components – Basic test and measurement procedures – Part 3-7: Examinations and measurements – Wavelength dependence of attenuation and return loss of single mode components IEC 61300-3-20, Fibre optic interconnecting devices and passive components – Basic test and measurement procedures – Part 3-20: Examinations and measurements – Directivity of fibre optic branching devices IEC 61753-1:2007, Fibre optic interconnecting devices and passive components performance standard – Part 1: General and guidance for performance standard Test Unless otherwise specified, all test methods are in accordance with the IEC 61300 series Each test defines the number of samples to be evaluated The samples shall have pigtails of single-mode fibres as per IEC 60793-2-50 type B 1.1 or B 1.3 in either coated fibres (primary and secondary) or reinforced cable format All measurements shall be carried out at normal room conditions, unless otherwise stated All tests shall be carried out over the operating wavelength ranges of 260 nm to 360 nm, 480 nm to 500 nm, and 550 nm to 560 nm, unless otherwise specified NOTE 310 nm, 490 nm and 550 nm are the nominal or centre wavelengths, stated f or the ranges 260 nm to 360 nm, 480 nm to 500 nm and 550 nm to 560 nm as defined in ITU-T Recommendations G.983.3 and G.984.2 and IEEE standard 802.3ah-2004 Test report Fully documented test reports and supporting evidence shall be prepared and be available for inspection as evidence that the tests have been carried out and complied with 5.1 Performance requirements Reference components The testing for these components does not require the use of reference components 5.2 Dimensions Dimensions shall comply with either an appropriate IEC interface standard or with those given in appropriate manufacturers drawings, where the IEC interface standard does not exist or cannot be used Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-28-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe –6– 5.3 –7– Sample size, sequencing and grouping Sample sizes for the tests are defined in Annex A of this document Test groups and test sequences shall be performed in sequential order as shown in Annex A The test sequence shown in Annex A shall be followed 5.4 Test details and requirements For test details and requirements, please see Table Table – Test details and requirements No Test Insertion loss (Attenuation) IEC 61300-3-7 Requirement £ 0,8 dB Insertion loss shall be met over the operating wavelength ranges Details Launch patchcord length: Source type: ³2m Launch conditions: The wavelength of the source shall be longer than cut-off wavelength of the fibre Test results shall be obtained under measurement uncertainty of ± 0,1 dB Other requirements: Wavelength isolation IEC 61300-3-7 ³ 18 dB between wavelength ranges 480 nm to 500 nm and 550 nm to 560 nm; ³ 30 dB between wavelength ranges 260 nm to 360 nm and 550 nm to 560 nm; Launch patchcord length: Source type: Launch conditions: Other requirements: Directivity ³ 50 dB Grade U IEC 61300-3-20 Directivity shall be met over the operating wavelength ranges Return loss ³ 50 dB Grade U IEC 61300-3-6 Return loss shall be met over the specified wavelength ranges Polarisation dependent loss (PDL) £ 0,2 dB IEC 61300-3-2 Polarisation dependent loss shall be met over the specified wavelength ranges Unpolarised ³2m Unpolarised The wavelength of the source shall be longer than the cut-off wavelength of the fibre Test results shall be obtained under measurement uncertainty of ±1 dB Source: Laser diode (LD) Other requirements: Test results shall be obtained under measurement uncertainty of ± dB All ports not under test shall be terminated to avoid unwanted reflections contributing to the measurement The directivity shall be measured between any pair of input or output ports Source: LD Other requirements: Test results shall be obtained under measurement uncertainty of ±1 dB All ports not under test shall be terminated to avoid unwanted reflections contributing to the measurement Launch patchcord length: Source type: ³2m Other requirements: Test results shall be obtained under measurement uncertainty of ± 0,05 dB LD Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-28-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe 61753-086-6 Ó IEC:2010 Table (continued) No Test Requirement Optical ower handling and damage threshold characterization ³ 300 mW (sum of power at the three wavelength ranges at the same time) IEC 61300-2-14, method During and on completion of the test the insertion loss limits of Test No shall be met After the test the isolation limits of Test No shall be met During and on completion of the test the return loss limits of Test No shall be met Damp heat (steady state) During and on completion of the test the insertion loss limits of Test No shall be met IEC 61300-2-19 After the test the isolation limits of Test No shall be met During and on completion of the test the return loss limits of Test No shall be met Vibration After the test the insertion loss limits of Test No shall be met IEC 61300-2-1 After the Test the isolation limits of test No shall be met After the test the return loss limits of Test No shall be met Details Source type LD Max power to be applied at wavelength range 550 nm to 560 nm: Max power to be applied at wavelength ranges 480 nm to 500 nm and 260 nm to 360 nm: Power increments: Test duration: 300 mW (+ ~25 dBm) Other requirements: Test results shall be obtained under insertion loss measurement uncertainty of ±0,1 dB Test results shall be obtained under return loss measurement uncertainty of ±1 dB Temperature: Humidity: Duration of the exposure: Maximum sampling interval during the test: Measurements required: + 75 °C ± °C 90 % RH ± % RH 168 h Frequency range: Constant vibration amplitude: Number of cycles (10 Hz - 55 Hz 10 Hz): Frequency change: Number of axes: Duration per axis: Measurements required: 10 mW (+ 10 dBm) dB 0,5 h at each power level 1h Insertion loss shall be measured before, during and after the test Return loss shall be measured before, during and after the test 10 Hz - 55 Hz 1,52 mm 15 octave/min orthogonal 2h Insertion loss shall be measured before and after the test Return loss shall be measured before and after the test Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-28-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe 61753-086-6 Ó IEC:2010 –8– Le texte de cette norme est issu des documents suivants: FDIS Rapport de vote 86B/3094/FDIS 86B/3132/RVD Le rapport de vote indiqué dans le tableau ci-dessus donne toute information sur le vote ayant abouti l'approbation de cette norme Cette publication a été rédigée selon les Directives ISO/CEI, Partie La liste de toutes les parties de la série CEI 61753, publiées sous le titre général Dispositifs d'interconnexion et composants passifs fibres optiques – Normes de performance, peut être consultée sur le site web de la CEI Le comité a décidé que le contenu de cette publication ne sera pas modifié avant la date de stabilité indiquée sur le site web de la CEI sous "http://webstore.iec.ch" dans les données relatives la publication recherchée A cette date, la publication sera • • • • reconduite, supprimée, remplacée par une édition révisée, ou amendée IMPORTANT – Le logo "colour inside" qui se trouve sur la page de couverture de cette publication indique qu'elle contient des couleurs qui sont considérées comme utiles une bonne compréhension de son contenu Les utilisateurs devraient, par conséquent, imprimer cette publication en utilisant une imprimante couleur AVERTISSEMENT Le présent document contient des éléments soumis Copyright Technologies, Inc ("Telcordia") Tous droits réservés © 2006, Telcordia Le lecteur est informé du fait que ce document CEI et la (les) source(s) de Telcordia peuvent différer, et le contexte et l’utilisation desdits éléments dans le présent document CEI peuvent différer de ceux de Telcordia TELCORDIA NE FAIT AUCUNE DECLARATION ET NE DONNE AUCUNE GARANTIE, EXPRESSE OU TACITE, QUANT A L'EXHAUSTIVITE, L’EXACTITUDE OU L’USAGE GENERAL DES INFORMATIONS OU DES OPINIONS CONTENUES DANS LE PRESENT DOCUMENT L'UTILISATEUR ASSUME TOUTE RESPONSABILITE QUANT A L'UTILISATION DE, OU A LA CONFIANCE FAITE A, CES INFORMATIONS OU OPINIONS TELCORDIA NE SAURAIT ETRE TENUE POUR RESPONSABLE DES DOMMAGES OU DES BLESSURES SUBIS PAR DES PERSONNES, QUI POURRAIENT RESULTER DE L'EXHAUSTIVITE, DE L’EXACTITUDE OU DE L’USAGE GENERAL DES INFORMATIONS OU DES OPINIONS CONTENUES DANS LE PRESENT DOCUMENT Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-28-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe 61753-086-6 Ó CEI:2010 – 18 –