IEC 60317 0 3 Edition 3 1 2013 09 CONSOLIDATED VERSION VERSION CONSOLIDÉE Specifications for particular types of winding wires – Part 0 3 General requirements – Enamelled round aluminium wire Spécific[.]
® Edition 3.1 2013-09 CONSOLIDATED VERSION VERSION CONSOLIDÉE colour inside Specifications for particular types of winding wires – Part 0-3: General requirements – Enamelled round aluminium wire IEC 60317-0-3:2008+A1:2013 Spécifications pour types particuliers de fils de bobinage – Partie 0-3: Exigences générales – Fil de section circulaire en aluminium émaillé Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe IEC 60317-0-3 All rights reserved Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IEC's member National Committee in the country of the requester If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information Droits de reproduction réservés Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence IEC Central Office 3, rue de Varembé CH-1211 Geneva 20 Switzerland Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 info@iec.ch www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies About IEC publications The technical content of IEC publications is kept under constant review by the IEC Please make sure that you have the latest edition, a corrigenda or an amendment might have been published Useful links: IEC publications search - www.iec.ch/searchpub Electropedia - www.electropedia.org The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,…) It also gives information on projects, replaced and withdrawn publications The world's leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages Also known as the International Electrotechnical Vocabulary (IEV) on-line IEC Just Published - webstore.iec.ch/justpublished Customer Service Centre - webstore.iec.ch/csc Stay up to date on all new IEC publications Just Published details all new publications released Available on-line and also once a month by email If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csc@iec.ch A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des Normes internationales pour tout ce qui a trait l'électricité, l'électronique et aux technologies apparentées A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu Veuillez vous assurer que vous possédez l’édition la plus récente, un corrigendum ou amendement peut avoir été publié Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub Electropedia - www.electropedia.org La recherche avancée vous permet de trouver des publications CEI en utilisant différents critères (numéro de référence, texte, comité d’études,…) Elle donne aussi des informations sur les projets et les publications remplacées ou retirées Le premier dictionnaire en ligne au monde de termes électroniques et électriques Il contient plus de 30 000 termes et dộfinitions en anglais et en franỗais, ainsi que les termes équivalents dans les langues additionnelles Egalement appelé Vocabulaire Electrotechnique International (VEI) en ligne Just Published CEI - webstore.iec.ch/justpublished Restez informé sur les nouvelles publications de la CEI Just Published détaille les nouvelles publications parues Disponible en ligne et aussi une fois par mois par email Service Clients - webstore.iec.ch/csc Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csc@iec.ch Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright â 2013 IEC, Geneva, Switzerland đ Edition 3.1 2013-09 CONSOLIDATED VERSION VERSION CONSOLIDÉE colour inside Specifications for particular types of winding wires – Part 0-3: General requirements – Enamelled round aluminium wire Spécifications pour types particuliers de fils de bobinage – Partie 0-3: Exigences générales – Fil de section circulaire en aluminium émaillé INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE ICS 29.060.10 ISBN 978-2-8322-1135-9 Warning! Make sure that you obtained this publication from an authorized distributor Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé ® Registered trademark of the International Electrotechnical Commission Marque déposée de la Commission Electrotechnique Internationale Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe IEC 60317-0-3 Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe Edition 3.1 2013-09 REDLINE VERSION VERSION REDLINE colour inside Specifications for particular types of winding wires – Part 0-3: General requirements – Enamelled round aluminium wire IEC 60317-0-3:2008+A1:2013 Spécifications pour types particuliers de fils de bobinage – Partie 0-3: Exigences générales – Fil de section circulaire en aluminium émaillé Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe ® IEC 60317-0-3 60317-0-3 IEC:2008+A1:2013 CONTENTS FOREWORD INTRODUCTION Scope Normative references Terms, definitions and, general notes on methods of tests and appearance 3.1 3.2 Definitions General notes on methods of test 3.2.1 Methods of test 3.2.2 Winding wire 3.3 Appearance Dimensions 4.1 4.2 4.3 Conductor diameter Out of roundness of conductor 11 Minimum increase in diameter due to the insulation and the bonding layer 11 4.3.1 Enamelled wires without a bonding layer 11 4.3.2 Enamelled wires with a bonding layer 11 4.4 Maximum overall diameter 11 4.4.1 Enamelled wires without a bonding layer 11 4.4.2 Enamelled wires with a bonding layer 11 Electrical resistance 12 Elongation 12 Springiness 12 Flexibility and adherence 12 8.1 Mandrel winding test (nominal conductor diameters up to and including 1,600 mm) 12 8.2 Stretching test (nominal conductor diameters over 1,000 mm) 12 8.3 Jerk test (nominal conductor diameters up to and including 1,000 mm) 13 8.4 Peel test (nominal conductor diameters over 1,000 mm) 13 Heat shock 13 9.1 Nominal conductor diameters up to and including 1,600 mm 13 9.2 Nominal conductor diameters over 1,600 mm 13 10 Cut-through 13 11 Resistance to abrasion 13 12 Resistance to solvents 13 13 Breakdown voltage 13 13.1 General 13 13.2 Nominal conductor diameters up to and including 2,500 mm 14 13.3 Nominal conductor diameters over 2,500 mm 14 14 Continuity of insulation (nominal conductor diameters up to and including 1,600 mm) 15 15 Temperature index 15 16 Resistance to refrigerants 15 17 Solderability 15 Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe –2– –3– 18 Heat or solvent bonding 15 19 Dielectric dissipation factor 15 20 Resistance to transformer oil 15 21 Loss of mass 16 23 Pin hole test 16 30 Packaging 16 Annex A (informative) Dimensions for intermediate nominal conductor diameters (R 40) 17 Annex B (informative) Method for the calculation of linear resistance 19 Annex C (informative) Resistance 20 Bibliography 21 Table – Dimensions of enamelled wires (R 20) Table – Dimensions of enamelled wires with a bonding layer (R 20) 11 Table – Elongation 12 Table – Mandrel winding 12 Table – Heat shock 13 Table – Breakdown voltage 14 Table – Breakdown voltage 14 Table – Continuity of insulation 15 Table A.1 – Dimensions of enamelled wires (R 40) 17 Table A.2 – Dimensions of enamelled wires with a bonding layer (R 40) 18 Table C.1 – Electrical resistances 20 Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe 60317-0-3 IEC:2008+A1:2013 60317-0-3 IEC:2008+A1:2013 INTERNATIONAL ELECTROTECHNICAL COMMISSION SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES – Part 0-3: General requirements – Enamelled round aluminium wire FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees) The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”) Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work International, governmental and nongovernmental organizations liaising with the IEC also participate in this preparation IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication 6) All users should ensure that they have the latest edition of this publication 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications 8) Attention is drawn to the Normative references cited in this publication Use of the referenced publications is indispensable for the correct application of this publication 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights IEC shall not be held responsible for identifying any or all such patent rights This Consolidated version of IEC 60317-0-3 bears the edition number 3.1 It consists of the third edition (2008) [documents 55/1056/FDIS et 55/1068/RVD] and its amendment (2012) [documents 55/1405/FDIS and 55/1426/RVD] The technical content is identical to the base edition and its amendment In this Redline version, a vertical line in the margin shows where the technical content is modified by amendment Additions and deletions are displayed in red, with deletions being struck through A separate Final version with all changes accepted is available in this publication This publication has been prepared for user convenience Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe –4– –5– International Standard IEC 60317-0-3 has been prepared by IEC technical committee 55: Winding wires Technical changes from the previous edition include clarification to appearance requirements, revisions to the wire size ranges applicable to the flexibility and adherence tests, and clarification that pin hole test requirements are under consideration This publication has been drafted in accordance with the ISO/IEC Directives, Part A list of all the parts in the IEC 60317 series, under the general title Specifications for particular types of winding wires, can be found on the IEC website This standard is to be read in conjunction with the IEC 60851 series The clause numbers used in this part of IEC 60317 are identical with the respective test numbers of IEC 60851 In case of inconsistencies between IEC 60851 and this part of IEC 60317, the latter shall prevail The committee has decided that the contents of the base publication and its amendment will remain unchanged until the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to the specific publication At this date, the publication will be • • • • reconfirmed, withdrawn, replaced by a revised edition, or amended IMPORTANT – The “colour inside” logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents Users should therefore print this publication using a colour printer Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe 60317-0-3 IEC:2008+A1:2013 60317-0-3 IEC:2008+A1:2013 INTRODUCTION This part of IEC 60317 is one of a series that deals with insulated wires used for windings in electrical equipment The series has three groups describing 1) winding wires and test methods (IEC 60851); 2) specifications for particular types of winding wires (IEC 60317); 3) packaging of winding wires (IEC 60264) Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison No further reproduction or distribution is permitted Uncontrolled when printe –6–