BS EN 61784-5-8:2013 BSI Standards Publication Industrial communication networks — Profiles Part 5-8: Installation of fieldbuses — Installation profiles for CPF BRITISH STANDARD BS EN 61784-5-8:2013 National foreword This British Standard is the UK implementation of EN 61784-5-8:2013 It is identical to IEC 61784-5-8:2013 The UK participation in its preparation was entrusted to Technical Committee AMT/7, Industrial communications: process measurement and control, including fieldbus A list of organizations represented on this committee can be obtained on request to its secretary This publication does not purport to include all the necessary provisions of a contract Users are responsible for its correct application © The British Standards Institution 2014 Published by BSI Standards Limited 2014 ISBN 978 580 84197 ICS 25.040.40; 35.100.40 Compliance with a British Standard cannot confer immunity from legal obligations This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2014 Amendments/corrigenda issued since publication Date Text affected BS EN 61784-5-8:2013 EN 61784-5-8 EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM December 2013 ICS 25.040.40; 35.100.40 English version Industrial communication networks Profiles Part 5-8: Installation of fieldbuses Installation profiles for CPF (IEC 61784-5-8:2013) Réseaux de communication industriels Profils Partie 5-8: Installation des bus de terrain Profils d'installation pour CPF (CEI 61784-5-8:2013) Industrielle Kommunikationsnetze Profile Teil 5-8: Feldbusinstallation Installationsprofile für die Kommunikationsprofilfamilie (IEC 61784-5-8:2013) This European Standard was approved by CENELEC on 2013-10-22 CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member This European Standard exists in three official versions (English, French, German) A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels © 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members Ref No EN 61784-5-8:2013 E BS EN 61784-5-8:2013 EN 61784-5-8:2013 -2- Foreword The text of document 65C/738/FDIS, future edition of IEC 61784-5-8, prepared by SC 65C "Industrial networks" of IEC/TC 65 "Industrial-process measurement, control and automation" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61784-5-8:2013 The following dates are fixed: • latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2014-07-22 • latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2016-10-22 This standard is to be used in conjunction with EN 61918:2013 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights Endorsement notice The text of the International Standard IEC 61784-5-8:2013 was approved by CENELEC as a European Standard without any modification BS EN 61784-5-8:2013 EN 61784-5-8:2013 -3- Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies Annex ZA of EN 61918:2013 applies, except as follows: Publication Year Title EN/HD Year EN 61918 2013 Addition to Annex ZA of EN 61918:2013: IEC 61918 2013 Industrial communication networks Installation of communication networks in industrial premises BS EN 61784-5-8:2013 –2– 61784-5-8 © IEC:2013 CONTENTS INTRODUCTION 14 Scope 15 Normative references 15 Terms, definitions and abbreviated terms 15 CPF 8: Overview of installation profiles 15 Installation profile conventions 16 Conformance to installation profiles 16 Annex A (normative) CP 8/1 and CP 8/2 (CC-Link/V1 and CC-Link/V2) specific installation profile 18 A.1 Installation profile scope 18 A.2 Normative references 18 A.3 Installation profile terms, definitions, and abbreviated terms 18 A.3.1 Terms and definitions 18 A.3.2 Abbreviated terms 18 A.3.3 Conventions for installation profiles 18 A.4 Installation planning 18 A.4.1 General 18 A.4.1.1 Objective 18 A.4.1.2 Cabling in industrial premises 18 A.4.1.3 The planning process 18 A.4.1.4 Specific requirements for CPs 18 A.4.1.5 Specific requirements for generic cabling in accordance with ISO/IEC 24702 19 A.4.2 Planning requirements 19 A.4.2.1 Safety 19 A.4.2.2 Security 19 A.4.2.3 Environmental considerations and EMC 19 A.4.2.4 Specific requirements for generic cabling in accordance with ISO/IEC 24702 19 A.4.3 Network capabilities 19 A.4.3.1 Network topology 19 A.4.3.2 Network characteristics 20 A.4.4 Selection and use of cabling components 21 A.4.4.1 Cable selection 21 A.4.4.2 Connecting hardware selection 23 A.4.4.3 Connections within a channel/permanent link 24 A.4.4.4 Terminators 24 A.4.4.5 Device location and connection 24 A.4.4.6 Coding and labelling 25 A.4.4.7 Earthing and bonding of equipment and devices and shielded cabling 25 A.4.4.8 Storage and transportation of cables 26 A.4.4.9 Routing of cables 26 A.4.4.10 Separation of circuit 26 A.4.4.11 Mechanical protection of cabling components 26 BS EN 61784-5-8:2013 61784-5-8 © IEC:2013 –3– A.4.4.12 Installation in special areas 26 A.4.5 Cabling planning documentation 26 A.4.6 Verification of cabling planning specification 26 A.5 Installation implementation 26 A.5.1 General requirements 26 A.5.1.1 Common description 26 A.5.1.2 Installation of CPs 26 A.5.1.3 Installation of generic cabling in industrial premises 26 A.5.2 Cable installation 26 A.5.2.1 General requirements for all cabling types 26 A.5.2.2 Installation and routing 27 A.5.2.3 Specific requirements for CPs 27 A.5.2.4 Specific requirements for wireless installation 27 A.5.2.5 Specific requirements for generic cabling in accordance with ISO/IEC 24702 27 A.5.3 Connector installation 27 A.5.3.1 Common description 27 A.5.3.2 Shielded connectors 28 A.5.3.3 Unshielded connectors 28 A.5.3.4 Specific requirements for CPs 28 A.5.3.5 Specific requirements for generic cabling in accordance with ISO/IEC 24702 28 A.5.4 Terminator installation 28 A.5.4.1 Common description 28 A.5.4.2 Specific requirements for CPs 28 A.5.5 Device installation 28 A.5.6 Coding and labelling 28 A.5.6.1 Common description 28 A.5.6.2 Specific requirements for CPs 28 A.5.7 Earthing and bonding of equipment and devices and shield cabling 28 A.5.7.1 Common description 28 A.5.7.2 Bonding and earthing of enclosures and pathways 28 A.5.7.3 Earthing methods 28 A.5.7.4 Shield termination methods 29 A.5.7.5 Specific requirements for CPs 29 A.5.7.6 Specific requirements for generic cabling in accordance with ISO/IEC 24702 29 A.5.8 As-implemented cabling documentation 29 A.6 Installation verification and installation acceptance test 29 A.6.1 General 29 A.6.2 Installation verification 29 A.6.2.1 General 29 A.6.2.2 Verification according to cabling planning documentation 29 A.6.2.3 Verification of earthing and bonding 29 A.6.2.4 Verification of shield earthing 29 A.6.2.5 Verification of cabling system 29 A.6.2.6 Cable selection verification 29 A.6.2.7 Connector verification 30 A.6.2.8 Connection verification 30 BS EN 61784-5-8:2013 –4– 61784-5-8 © IEC:2013 A.6.2.9 Terminators verification 30 A.6.2.10 Coding and labelling verification 30 A.6.2.11 Verification report 30 A.6.3 Installation acceptance test 30 A.6.3.1 General 30 A.6.3.2 Acceptance test of Ethernet-based cabling 30 A.6.3.3 Acceptance test of non-Ethernet-based cabling 30 A.6.3.4 Specific requirements for wireless installation 30 A.6.3.5 Acceptance test report 30 A.7 Installation administration 31 A.8 Installation maintenance and installation troubleshooting 31 Annex B (normative) CP 8/3 (CC-Link/LT) specific installation profile 32 B.1 Installation profile scope 32 B.2 Normative references 32 B.3 Installation profile terms, definitions, and abbreviated terms 32 B.3.1 Terms and definitions 32 B.3.2 Abbreviated terms 32 B.3.3 Conventions for installation profiles 32 B.4 Installation planning 32 B.4.1 General 32 B.4.1.1 Objective 32 B.4.1.2 Cabling in industrial premises 32 B.4.1.3 The planning process 32 B.4.1.4 Specific requirements for CPs 32 B.4.1.5 Specific requirements for generic cabling in accordance with ISO/IEC 24702 33 B.4.2 Planning requirements 33 B.4.2.1 Safety 33 B.4.2.2 Security 33 B.4.2.3 Environmental considerations and EMC 33 B.4.2.4 Specific requirements for generic cabling in accordance with ISO/IEC 24702 33 B.4.3 Network capabilities 33 B.4.3.1 Network topology 33 B.4.3.2 Network characteristics 34 B.4.4 Selection and use of cabling components 36 B.4.4.1 Cable selection 36 B.4.4.2 Connecting hardware selection 38 B.4.4.3 Connections within a channel/permanent link 40 B.4.4.4 Terminators 41 B.4.4.5 Device location and connection 41 B.4.4.6 Coding and labelling 41 B.4.4.7 Earthing and bonding of equipment and devices and shielded cabling 41 B.4.4.8 Storage and transportation of cables 42 B.4.4.9 Routing of cables 42 B.4.4.10 Separation of circuit 42 B.4.4.11 Mechanical protection of cabling components 42 B.4.4.12 Installation in special areas 42 BS EN 61784-5-8:2013 61784-5-8 © IEC:2013 –5– B.4.5 Cabling planning documentation 43 B.4.6 Verification of cabling planning specification 43 B.5 Installation implementation 43 B.5.1 General requirements 43 B.5.1.1 Common description 43 B.5.1.2 Installation of CPs 43 B.5.1.3 Installation of generic cabling in industrial premises 43 B.5.2 Cable installation 43 B.5.2.1 General requirements for all cabling types 43 B.5.2.2 Installation and routing 44 B.5.2.3 Specific requirements for CPs 44 B.5.2.4 Specific requirements for wireless installation 44 B.5.2.5 Specific requirements for generic cabling in accordance with ISO/IEC 24702 44 B.5.3 Connector installation 44 B.5.3.1 Common description 44 B.5.3.2 Shielded connectors 44 B.5.3.3 Unshielded connectors 45 B.5.3.4 Specific requirements for CPs 45 B.5.3.5 Specific requirements for generic cabling in accordance with ISO/IEC 24702 45 B.5.4 Terminator installation 45 B.5.4.1 Common description 45 B.5.4.2 Specific requirements for CPs 45 B.5.5 Device installation 45 B.5.6 Coding and labelling 45 B.5.7 Earthing and bonding of equipment and devices and shield cabling 45 B.5.7.1 Common description 45 B.5.7.2 Bonding and earthing of enclosures and pathways 45 B.5.7.3 Earthing methods 45 B.5.7.4 Shield termination methods 45 B.5.7.5 Specific requirements for CPs 45 B.5.7.6 Specific requirements for generic cabling in accordance with ISO/IEC 24702 46 B.5.8 As-implemented cabling documentation 46 B.6 Installation verification and installation acceptance test 46 B.6.1 General 46 B.6.2 Installation verification 46 B.6.2.1 General 46 B.6.2.2 Verification according to cabling planning documentation 46 B.6.2.3 Verification of earthing and bonding 46 B.6.2.4 Verification of shield earthing 46 B.6.2.5 Verification of cabling system 46 B.6.2.6 Cable selection verification 46 B.6.2.7 Connector verification 46 B.6.2.8 Connection verification 46 B.6.2.9 Terminators verification 47 B.6.2.10 Coding and labelling verification 47 B.6.2.11 Verification report 47 BS EN 61784-5-8:2013 –6– 61784-5-8 © IEC:2013 B.6.3 Installation acceptance test 47 B.6.3.1 General 47 B.6.3.2 Acceptance test of Ethernet-based cabling 47 B.6.3.3 Acceptance test of non-Ethernet-based cabling 47 B.6.3.4 Specific requirements for wireless installation 47 B.6.3.5 Acceptance test report 47 B.7 Installation administration 47 B.8 Installation maintenance and installation troubleshooting 47 Annex C (normative) CP 8/4 (CC-Link IE Controller Network) specific installation profile 48 C.1 Installation profile scope 48 C.2 Normative references 48 C.3 Installation profile terms, definitions, and abbreviated terms 48 C.3.1 Terms and definitions 48 C.3.2 Abbreviated terms 48 C.3.3 Conventions for installation profiles 48 C.4 Installation planning 48 C.4.1 General 48 C.4.1.1 Objective 48 C.4.1.2 Cabling in industrial premises 48 C.4.1.3 The planning process 48 C.4.1.4 Specific requirements for CPs 48 C.4.1.5 Specific requirements for generic cabling in accordance with ISO/IEC 24702 48 C.4.2 Planning requirements 48 C.4.2.1 Safety 48 C.4.2.2 Security 49 C.4.2.3 Environmental considerations and EMC 49 C.4.2.4 Specific requirements for generic cabling in accordance with ISO/IEC 24702 49 C.4.3 Network capabilities 49 C.4.3.1 Network topology 49 C.4.3.2 Network characteristics 49 C.4.4 Selection and use of cabling components 50 C.4.4.1 Cable selection 50 C.4.4.2 Connecting hardware selection 51 C.4.4.3 Connections within a channel/permanent link 52 C.4.4.4 Terminators 53 C.4.4.5 Device location and connection 53 C.4.4.6 Coding and labelling 53 C.4.4.7 Earthing and bonding of equipment and devices and shielded cabling 53 C.4.4.8 Storage and transportation of cables 54 C.4.4.9 Routing of cables 54 C.4.4.10 Separation of circuit 54 C.4.4.11 Mechanical protection of cabling components 54 C.4.4.12 Installation in special areas 55 C.4.5 Cabling planning documentation 55 C.4.5.1 Common description 55 BS EN 61784-5-8:2013 – 62 – D.4.2.1.5 61784-5-8 © IEC:2013 Safety of optical fibre communication systems Not applicable D.4.2.2 Security D.4.2.3 Environmental considerations and EMC D.4.2.3.1 Description methodology D.4.2.3.2 Use of the described environment to produce a bill of material D.4.2.4 D.4.3 D.4.3.1 Specific requirements for generic cabling in accordance with ISO/IEC 24702 Network capabilities Network topology D.4.3.1.1 Common description D.4.3.1.2 Basic physical topologies for passive networks Not applicable D.4.3.1.3 Basic physical topologies for active networks D.4.3.1.4 Combination of basic topologies D.4.3.1.5 Specific requirements for CPs Not applicable D.4.3.1.6 D.4.3.2 Specific requirements for generic cabling in accordance with ISO/IEC 24702 Network characteristics D.4.3.2.1 General D.4.3.2.2 Network characteristics for balanced cabling not based on Ethernet Not applicable D.4.3.2.3 Network characteristics for balanced cabling based on Ethernet Replacement: Table D.1 provides values based on the template given in IEC 61918:2013, Table BS EN 61784-5-8:2013 61784-5-8 © IEC:2013 – 63 – Table D.1 – Network characteristics for balanced cabling based on Ethernet Characteristic CP 8/5 Supported data rates (Mbit/s) Supported channel length (m) 000 b 23 900 Number of connections in the channel (max.) Patch cord length (m) a, b 253 a Channel class per ISO/IEC 24702 (min.) 100 b Cable category per ISO/IEC 24702 (min.) D c 5e Connecting HW category per ISO/IEC 24702 (min.) Cable types 5e ANSI/TIA/EIA-568-B a See D.4.4.3.2 b For the purpose of this table the channel definitions of ISO/IEC 24702 are applicable c Additional information is available in IEC 61156 series D.4.3.2.4 Network characteristics for optical fibre cabling Not applicable D.4.3.2.5 Specific network characteristics Not applicable D.4.3.2.6 D.4.4 Specific requirements for generic cabling in accordance with ISO/IEC 24702 Selection and use of cabling components D.4.4.1 Cable selection D.4.4.1.1 Common description D.4.4.1.2 Copper cables D.4.4.1.2.1 Balanced cables for Ethernet-based CPs Replacement: Table D.2 provides values based on the template given in IEC 61918:2013, Table BS EN 61784-5-8:2013 – 64 – 61784-5-8 © IEC:2013 Table D.2 – Information relevant to copper cable: fixed cables Characteristic CP 8/5 100 Nominal impedance of cable (Ω) DCR of conductors (Ω/km) < 115 DCR of shield (Ω/km) – Number of conductors Shielding Aluminium tape over annealed copper braided wire Colour code for conductor – Jacket colour requirements – Jacket material Application dependent Resistance to harsh environment (e.g UV, oil resist, LS0H) Application dependent Agency ratings Application dependent Standard IEEE 802.3, 1000Base-T ANSI/TIA/EIA-568-B, Category 5e D.4.4.1.2.2 Copper cables for non-Ethernet-based CPs Not applicable D.4.4.1.3 Cables for wireless installation Not applicable D.4.4.1.4 Optical fibre cables Not applicable D.4.4.1.5 Special purpose balanced and optical fibre cables Not applicable D.4.4.1.6 Specific requirements for CPs Not applicable D.4.4.1.7 D.4.4.2 Specific requirements for generic cabling in accordance with ISO/IEC 24702 Connecting hardware selection D.4.4.2.1 Common description D.4.4.2.2 Connecting hardware for balanced cabling CPs based on Ethernet Replacement: Table D.3 provides values based on the template given in IEC 61918:2013, Table BS EN 61784-5-8:2013 61784-5-8 © IEC:2013 – 65 – Table D.3 – Connectors for balanced cabling CPs based on Ethernet IEC 60603-7 series CP 8/5 a IEC 61076-3106 b IEC 61076-3117 b IEC 61076-2101 IEC 61076-2109 shielded unshielded Var Var Var 14 M12-4 with D-coding M12-8 with X-coding IEC 60603-7-3 No No No No No No a For IEC 60603-7 series, the connector selection is based on the desired channel performance b Housings to protect connectors D.4.4.2.3 Connecting hardware for copper cabling CPs not based on Ethernet Not applicable D.4.4.2.4 Connecting hardware for wireless installation Not applicable D.4.4.2.5 Connecting hardware for optical fibre cabling Not applicable D.4.4.2.6 Specific requirements for CPs Not applicable D.4.4.2.7 D.4.4.3 Specific requirements for generic cabling in accordance with ISO/IEC 24702 Connections within a channel/permanent link D.4.4.3.1 Common description D.4.4.3.2 Balanced cabling connections and splices for CPs based on Ethernet D.4.4.3.2.1 Common description D.4.4.3.2.2 Connections minimum distance D.4.4.3.2.3 Balanced cabling splices D.4.4.3.2.4 Balanced cabling bulkhead connections D.4.4.3.2.5 Balanced cabling J-J adaptors D.4.4.3.3 Copper cabling connections and splices for CPs not based on Ethernet Not applicable D.4.4.3.4 Optical fibre cabling connections and splices for CPs based on Ethernet Not applicable D.4.4.3.5 Optical fibre cabling connections and splices for CPs not based on Ethernet Not applicable BS EN 61784-5-8:2013 – 66 – D.4.4.3.6 D.4.4.4 61784-5-8 © IEC:2013 Specific requirements for generic cabling in accordance with ISO/IEC 24702 Terminators Not applicable D.4.4.5 Device location and connection D.4.4.5.1 Common description D.4.4.5.2 Specific requirements for CPs Not applicable D.4.4.5.3 Specific requirements for wireless installation Not applicable D.4.4.5.4 D.4.4.6 Specific requirements for generic cabling in accordance with ISO/IEC 24702 Coding and labelling D.4.4.6.1 Common description D.4.4.6.2 Additional requirements for CPs Not applicable D.4.4.6.3 Specific requirements for CPs Not applicable D.4.4.6.4 D.4.4.7 D.4.4.7.1 Specific requirements for generic cabling in accordance with ISO/IEC 24702 Earthing and bonding of equipment and devices and shielded cabling Common description D.4.4.7.1.1 Basic requirements D.4.4.7.1.2 Planner tasks D.4.4.7.1.3 Methods for controlling potential differences in the earth system D.4.4.7.1.4 Selection of the earthing and bonding systems D.4.4.7.2 Bonding and earthing of enclosures and pathways D.4.4.7.2.1 Equalisation and earthing conductor sizing and length D.4.4.7.2.2 Bonding straps and sizing BS EN 61784-5-8:2013 61784-5-8 © IEC:2013 – 67 – D.4.4.7.2.3 Surface preparation and methods D.4.4.7.2.4 Bonding and earthing D.4.4.7.3 Earthing methods D.4.4.7.3.1 Equipotential Not applicable D.4.4.7.3.2 Star D.4.4.7.3.3 Earthing of equipment (devices) Addition: A parallel RC earthing circuit shall not be used for CP 8/5 networks D.4.4.7.3.4 D.4.4.7.4 Copper bus bars Shield earthing D.4.4.7.4.1 Non-earthing or parallel RC Not applicable D.4.4.7.4.2 Direct D.4.4.7.4.3 Derivatives of direct and parallel RC Not applicable D.4.4.7.5 Specific requirements for CPs Not applicable D.4.4.7.6 D.4.4.8 Specific requirements for generic cabling in accordance with ISO/IEC 24702 Storage and transportation of cables D.4.4.8.1 Common description D.4.4.8.2 Specific requirements for CPs Not applicable D.4.4.8.3 D.4.4.9 Specific requirements for generic cabling in accordance with ISO/IEC 24702 Routing of cables BS EN 61784-5-8:2013 – 68 – 61784-5-8 © IEC:2013 D.4.4.9.1 Common description D.4.4.9.2 Cable routing of assemblies D.4.4.9.3 Detailed requirements for cable routing inside enclosures D.4.4.9.4 Cable routing inside buildings D.4.4.9.5 Cable routing outside and between buildings D.4.4.9.6 Installing redundant communication cables D.4.4.10 Separation of circuit D.4.4.11 Mechanical protection of cabling components D.4.4.11.1 Common description D.4.4.11.2 Specific requirements for CPs Not applicable D.4.4.11.3 D.4.4.12 Specific requirements for generic cabling in accordance with ISO/IEC 24702 Installation in special areas D.4.4.12.1 Common description D.4.4.12.2 Specific requirements for CPs Not applicable D.4.4.12.3 D.4.5 Specific requirements for generic cabling in accordance with ISO/IEC 24702 Cabling planning documentation D.4.5.1 Common description D.4.5.2 Cabling planning documentation for CPs Not applicable D.4.5.3 Network certification documentation D.4.5.4 Cabling planning documentation for generic cabling in accordance with ISO/IEC 24702 D.4.6 D.5 Verification of cabling planning specification Installation implementation D.5.1 General requirements D.5.1.1 Common description D.5.1.2 Installation of CPs D.5.1.3 Installation of generic cabling in industrial premises D.5.2 Cable installation BS EN 61784-5-8:2013 61784-5-8 © IEC:2013 D.5.2.1 – 69 – General requirements for all cabling types D.5.2.1.1 Storage and installation D.5.2.1.2 Protecting communication cables against potential mechanical damage Replacement: Table D.4 provides values based on the template given in IEC 61918:2013, Table 18 Table D.4 – Parameters for balanced cables Characteristic Minimum bending radius, single bending (mm) Bending radius, multiple bending (mm) Mechanical Pull forces (N) force a a a Permanent tensile forces (N) a Maximum lateral forces (N/cm) a Temperature range during installation (°C) a Value -20 to +70 Depending on cable type: see manufacturer’s data sheet D.5.2.1.3 Avoid forming loops D.5.2.1.4 Torsion (twisting) D.5.2.1.5 Tensile strength (on installed cables) D.5.2.1.6 Bending radius D.5.2.1.7 Pull force D.5.2.1.8 Fitting strain relief D.5.2.1.9 Installing cables in cabinet and enclosures D.5.2.1.10 Installation on moving parts D.5.2.1.11 Cable crush D.5.2.1.12 Installation of continuous flexing cables D.5.2.1.13 Additional instructions for the installation of optical fibre cables Not applicable D.5.2.2 Installation and routing D.5.2.2.1 Common description D.5.2.2.2 Separation of circuits D.5.2.3 Specific requirements for CPs Not applicable D.5.2.4 Specific requirements for wireless installation Not applicable BS EN 61784-5-8:2013 – 70 – D.5.2.5 D.5.3 61784-5-8 © IEC:2013 Specific requirements for generic cabling in accordance with ISO/IEC 24702 Connector installation D.5.3.1 Common description D.5.3.2 Shielded connectors D.5.3.3 Unshielded connectors Not applicable D.5.3.4 Specific requirements for CPs Not applicable D.5.3.5 D.5.4 Specific requirements for generic cabling in accordance with ISO/IEC 24702 Terminator installation Not applicable D.5.5 Device installation D.5.5.1 Common description D.5.5.2 Specific requirements for CPs Not applicable D.5.6 Coding and labelling D.5.6.1 Common description D.5.6.2 Specific requirements for CPs Not applicable D.5.7 Earthing and bonding of equipment and devices and shield cabling D.5.7.1 Common description D.5.7.2 Bonding and earthing of enclosures and pathways D.5.7.2.1 Equalisation and earthing conductor sizing and length D.5.7.2.2 Bonding straps and sizing D.5.7.2.3 Surface preparation and methods D.5.7.3 D.5.7.3.1 Earthing methods Equipotential Not applicable D.5.7.3.2 Star D.5.7.3.3 Earthing of equipment (devices) D.5.7.3.3.1 Not applicable Non-earthing or parallel RC BS EN 61784-5-8:2013 61784-5-8 © IEC:2013 – 71 – D.5.7.3.3.2 Direct D.5.7.3.3.3 Installing copper bus bars D.5.7.4 Shield termination methods D.5.7.4.1 General D.5.7.4.2 Parallel RC Not applicable D.5.7.4.3 Direct D.5.7.4.4 Derivatives of direct and parallel RC Not applicable D.5.7.5 Specific requirements for CPs Not applicable D.5.7.6 D.5.8 D.6 Specific requirements for generic cabling in accordance with ISO/IEC 24702 As-implemented cabling documentation Installation verification and installation acceptance test D.6.1 General D.6.2 Installation verification D.6.2.1 General D.6.2.2 Verification according to cabling planning documentation D.6.2.3 Verification of earthing and bonding D.6.2.3.1 General D.6.2.3.2 Specific requirements for earthing and bonding D.6.2.4 Verification of shield earthing D.6.2.5 Verification of cabling system D.6.2.5.1 Verification of cable routing D.6.2.5.2 Verification of cable protection and proper strain relief D.6.2.6 Cable selection verification D.6.2.6.1 Common description D.6.2.6.2 Specific requirements for CPs Not applicable D.6.2.6.3 D.6.2.7 Specific requirements for wireless installation Connector verification BS EN 61784-5-8:2013 – 72 – D.6.2.7.1 Common description D.6.2.7.2 Specific requirements for CPs 61784-5-8 © IEC:2013 Not applicable D.6.2.7.3 Specific requirements for wireless installation Not applicable D.6.2.8 Connection verification D.6.2.8.1 Common description D.6.2.8.2 Number of connections and connectors D.6.2.8.3 Wire mapping D.6.2.9 Terminators verification Not applicable D.6.2.10 Coding and labelling verification D.6.2.10.1 Common description D.6.2.10.2 Specific coding and labelling verification requirements Not applicable D.6.2.11 D.6.3 Verification report Installation acceptance test D.6.3.1 General D.6.3.2 Acceptance test of Ethernet-based cabling D.6.3.2.1 Validation of balanced cabling for CPs based on Ethernet D.6.3.2.1.1 Common description D.6.3.2.1.2 Transmission performance test parameters D.6.3.2.1.3 Specific requirements for CPs based on Ethernet Not applicable D.6.3.2.2 Validation of optical fibre cabling for CPs based on Ethernet Not applicable D.6.3.2.3 D.6.3.3 Specific requirements for generic cabling in accordance with ISO/IEC 24702 Acceptance test of non-Ethernet-based cabling Not applicable D.6.3.4 Specific requirements for wireless installation Not applicable BS EN 61784-5-8:2013 61784-5-8 © IEC:2013 D.6.3.5 D.7 – 73 – Acceptance test report Installation administration Subclause 7.8 is not applicable D.8 Installation maintenance and installation troubleshooting Subclause 8.4 is not applicable BS EN 61784-5-8:2013 – 74 – 61784-5-8 © IEC:2013 Bibliography Addition: [27] CC-Link open field network cable wiring manual, November 2008, CC-Link Partner Association, available at [28] CC-Link IE Controller Network cable installation manual, September 2008, CC-Link Partner Association, available at [29] CC-Link IE Field Network cable installation manual, June 2010, CC-Link Partner Association, available at This page deliberately left blank NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW British Standards Institution (BSI) BSI is the national body responsible for preparing British Standards and other standards-related publications, information and services BSI is incorporated by Royal Charter British Standards and other standardization products are published by BSI Standards Limited About us Revisions We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions Our British Standards and other publications are updated by amendment or revision The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process Organizations of all sizes and across all sectors choose standards to help them achieve their goals Information on standards We can provide you with the knowledge that your organization needs to succeed Find out more about British Standards by visiting our website at bsigroup.com/standards or contacting our Customer Services team or Knowledge Centre Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at bsigroup.com/shop, where hard copies can also be purchased If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team Subscriptions Our range of subscription services are designed to make using standards easier for you For further information on our subscription products go to bsigroup.com/subscriptions With British Standards Online (BSOL) you’ll have instant access to over 55,000 British and adopted European and international standards from your desktop It’s available 24/7 and is refreshed daily so you’ll always be up to date You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member PLUS is an updating service exclusive to BSI Subscribing Members You will automatically receive the latest hard copy of your standards when they’re revised or replaced To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit bsigroup.com/shop With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet Licences can cover as few or as many users as you wish With updates supplied as soon as they’re available, you can be sure your documentation is current For further information, email bsmusales@bsigroup.com BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK We continually improve the quality of our products and services to benefit your business If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre Copyright All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means – electronic, photocopying, recording or otherwise – without prior written permission from BSI Details and advice can be obtained from the Copyright & Licensing Department Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): orders@bsigroup.com Email (enquiries): cservices@bsigroup.com Subscriptions Tel: +44 845 086 9001 Email: subscriptions@bsigroup.com Knowledge Centre Tel: +44 20 8996 7004 Email: knowledgecentre@bsigroup.com Copyright & Licensing Tel: +44 20 8996 7070 Email: copyright@bsigroup.com