BS EN 60335-2-5:2015 corrigendum June 2015 BSIncorporating EN 60335-2-5:2015 BSI Standards Publication Household and similar electrical appliances — Safety Part 2-5: Particular requirements for dishwashers BS EN 60335-2-5:2015 BRITISH STANDARD National foreword This British Standard is the UK implementation of EN 60335-2-5:2015 It is derived from IEC 60335-2-5:2012 It supersedes BS EN 60335-2-5:2003+A12:2012, which will be withdrawn on August 2016 The CENELEC common modifications have been implemented at the appropriate places in the text The start and finish of each common modification is indicated in the text by tags The UK participation in its preparation was entrusted to Technical Committee CPL/61, Safety of household and similar electrical appliances A list of organizations represented on this committee can be obtained on request to its secretary This publication does not purport to include all the necessary provisions of a contract Users are responsible for its correct application © The British Standards Institution 2015 Published by BSI Standards Limited 2015 ISBN 978 580 90626 ICS 13.120; 97.040.40 Compliance with a British Standard cannot confer immunity from legal obligations This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2015 Amendments/corrigenda issued since publication Date Text affected 30 June 2015 Corrected to include CENELEC Common Modifications EUROPEAN STANDARD EN 60335-2-5 NORME EUROPÉENNE EUROPÄISCHE NORM April 2015 ICS 13.120; 97.040.40 Supersedes EN 60335-2-5:2003 English Version Household and similar electrical appliances - Safety Part 2-5: Particular requirements for dishwashers (IEC 60335-2-5:2012 , modified) Appareils électrodomestiques et analogues - Sécurité Partie 2-5: Exigences particulières pour les lave-vaisselle (IEC 60335-2-5:2012 , modifiée) Sicherheit elektrischer Geräte für den Hausgebrauch und ähnliche Zwecke - Teil 2-5: Besondere Anforderungen für Geschirrspülmaschinen (IEC 60335-2-5:2012 , modifiziert) This European Standard was approved by CENELEC on 2013-08-09 CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member This European Standard exists in three official versions (English, French, German) A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels © 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members Ref No EN 60335-2-5:2015 E BS EN 60335-2-5:2015 EN 60335-2-5:2015 BS EN 60335-2-5:2015 EN 60335-2-5:2015 –- 32 -– Foreword The text of document 61/4450/FDIS, future edition of IEC 60335-2-5, prepared by IEC/TC 61 "Safety of household and similar electrical appliances " was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60335-2-5:2015 A draft amendment, which covers common modifications to IEC 60335-2-5:2012, was prepared by CLC/TC 61, "Safety of household and similar electrical appliances" and approved by CENELEC The following dates are fixed: – latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2015-10-24 – latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2016-08-09 This document supersedes EN 60335-2-5:2003 EN 60335-2-5:2015 includes the following EN 60335-2-5:2003 and its amendments: significant technical changes with respect to – added requirements to 22.104 to address switch issues; – converted notes to normative text (3.1.9, 7.12, 10.1, 10.2, 15.101, 22.6, 22.103, AA.1, AA.2, Annex BB – Clause 4); – deleted notes (19.101, 22.6, 23.101, AA.2) This Part is to be used in conjunction with the latest edition of EN 60335-1 and its amendments It was established on the basis of EN 60335-1:2012 NOTE When "Part 1" is mentioned in this standard, it refers to EN 60335-1 This Part supplements or modifies the corresponding clauses of EN 60335-1, so as to convert it into the European Standard: Safety requirements for electric dishwashers When a particular subclause of Part is not mentioned in this Part 2, that subclause applies as far as is reasonable When this standard states "addition", "modification" or "replacement", the relevant text of Part is to be adapted accordingly NOTE The following numbering system is used: – subclauses, tables and figures that are numbered starting from 101 are additional to those in Part 1; – unless notes are in a new subclause or involve notes in Part 1, they are numbered starting from 101, including those in a replaced clause or subclause; – additional annexes are lettered AA, BB, etc.; – clauses, subclauses, notes, tables, figures and annexes that are additional to those in the IEC standard are prefixed with the letter Z BS EN 60335-2-5:2015 EN 60335-2-5:2015 NOTE –3– -4- BS EN 60335-2-5:2015 EN 60335-2-5:2015 The following print types are used: – requirements: in roman type; – test specifications: in italic type; – notes: in small roman type Words in bold in the text are defined in Clause When a definition concerns an adjective, the adjective and the associated noun are also in bold Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment Designed for Use within Certain Voltage Limits (LVD - 2006/95/EC) Endorsement notice The text of the International Standard IEC 60335-2-5:2012 was approved by CENELEC as a European Standard with agreed common modifications COMMON MODIFICATIONS Introduction Add the following: An investigation by CLC/TC 61 has shown that all risks from products within the scope of this standard are fully covered by the Low Voltage Directive, 2006/95/EC Scope Replace the text by the following: This clause of Part is replaced by the following This European Standard deals with the safety of electric dishwashers for household and similar purposes, that are intended for washing and rinsing dishes, cutlery and other utensils, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances Appliances intended to be used by laymen in shops and other premises for normal housekeeping purposes, are within the scope of this European Standard BS EN 60335-2-5:2015 EN 60335-2-5:2015 -7- BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 –4– Add the following: Annex ZC (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies Addition: Publication Year Title EN/HD IEC 60436 – Electric dishwashers for household use – Methods for measuring the performance EN 50242/EN 60436 - ISO 1817 2011 Rubber, vulcanised or thermoplastic – Determination of the effect of liquids – – 2002 Paper, board, pulps and related terms – Vocabulary Part 4: Paper and board grades and converted products – – ISO 4046-4 Year –5– –2– –2– CONTENTS BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 CONTENTS FOREWORD INTRODUCTION FOREWORD 10 Scope INTRODUCTION Normative references .11 Scope Terms and references definitions Normative .11 7 Classification 12 General conditions for the tests 12 Marking and instructions Classification 8 10 11 10 12 11 13 12 14 13 15 14 16 15 17 16 18 17 19 18 20 19 21 20 22 21 23 22 24 23 25 24 26 25 27 26 28 27 29 28 30 29 31 30 General requirement Terms and definitions 11 12 General conditions for the tests General requirement Protection against access to live parts 13 Marking and instructions 13 Starting of against motor-operated appliances Protection access to live parts 13 Power and current Startinginput of motor-operated appliances 13 Heating 10 Power input and current Void 14 10 Heating 10 Leakage current and electric strength at operating temperature 14 10 Void 10 Transient overvoltages 10 Leakage current and electric strength at operating temperature 14 10 15 Moisture resistance 10 Transient overvoltages 10 Leakage and electric strength 16 12 Moisture current resistance 10 16 Overload protection of transformers and associated circuits 12 Leakage current and electric strength 12 Endurance 12 Overload protection of transformers and associated circuits 16 12 16 Abnormal operation 12 Endurance 12 Stability mechanical hazards 17 12 Abnormaland operation 12 17 Mechanical strength 13 Stability and mechanical hazards 12 Construction 13 Mechanical strength 18 13 19 Internal wiring 15 Construction 13 Components 15 Internal wiring 19 15 19 Supply connection and external flexible cords 15 Components 15 Terminals for external 15 Supply connection andconductors external flexible cords 20 15 20 Provision for earthing Terminals for external conductors 15 15 Screws and 20 16 Provision forconnections earthing 15 20 Clearances, creepage distances and solid insulation 16 Screws and connections 16 Resistance heat anddistances fire 16 Clearances,tocreepage and solid insulation 20 16 20 Resistance to rusting 16 Resistance to heat and fire 16 32 and similar hazards 20 16 31 Radiation, Resistancetoxicity to rusting 16 Annexes 17 32 Radiation, toxicity and similar hazards 21 16 Annex AA (normative) Detergent and rinsing agent 21 17 Annexes 17 23 Annex BB (normative) Ageing test for elastomeric parts 19 Annex AA (normative) Detergent and rinsing agent 17 Bibliography 21 Annex BB (normative) Ageing test for elastomeric parts 25 19 Bibliography 21 Table Z101 – Maximum temperature rises for external surfaces under normal Table AA.1 – Detergent composition 14 17 operating conditions � ���������������������������������������������������������������������������������������������������������������� Table agent composition 21 17 Table AA.2 AA.1 – – Rinsing Detergent composition 17 Table AA.2 – Rinsing agent composition 21 17 BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 –6– –3– INTERNATIONAL ELECTROTECHNICAL COMMISSION _ HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES – SAFETY – Part 2-5: Particular requirements for dishwashers FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees) The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”) Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work International, governmental and nongovernmental organizations liaising with the IEC also participate in this preparation IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter 5) IEC itself does not provide any attestation of conformity Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity IEC is not responsible for any services carried out by independent certification bodies 6) All users should ensure that they have the latest edition of this publication 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications 8) Attention is drawn to the Normative references cited in this publication Use of the referenced publications is indispensable for the correct application of this publication 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights IEC shall not be held responsible for identifying any or all such patent rights This part of International Standard IEC 60335 has been prepared by IEC technical committee 61: Safety of household and similar electrical appliances This sixth edition cancels and replaces the fifth edition published in 2002 including its Amendment (2005) and its Amendment (2008) It constitutes a technical revision The principal changes in this edition as compared with the fifth edition of IEC 60335-2-5 are as follows (minor changes are not listed): • added requirements to 22.104 to address switch issues; • converted notes to normative text (3.1.9, 7.12, 10.1, 10.2, 15.101, 22.6, 22.103, AA.1, AA.2, Annex BB – Clause 4); • deleted notes (19.101, 22.6, 23.101, AA.2) BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 –7– –4– The text of this standard is based on the following documents: FDIS Report on voting 61/4450/FDIS 61/4503/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table This publication has been drafted in accordance with the ISO/IEC Directives, Part This part is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments It was established on the basis of the fifth edition (2010) of that standard NOTE When “Part 1” is mentioned in this standard, it refers to IEC 60335-1 This part supplements or modifies the corresponding clauses in IEC 60335-1, so as to convert that publication into the IEC standard: Safety requirements for dishwashers When a particular subclause of Part is not mentioned in this part 2, that subclause applies as far as is reasonable When this standard states “addition”, “modification” or “replacement”, the relevant text in Part is to be adapted accordingly NOTE The following numbering system is used: – subclauses, tables and figures that are numbered starting from 101 are additional to those in Part 1; – unless notes are in a new subclause or involve notes in Part 1, they are numbered starting from 101, including those in a replaced clause or subclause; – additional annexes are lettered AA, BB, etc NOTE The following print types are used: – requirements: in roman type; – test specifications: in italic type; – notes: in small roman type Words in bold in the text are defined in Clause When a definition concerns an adjective, the adjective and the associated noun are also in bold The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to the specific publication At this date, the publication will be • • • • reconfirmed, withdrawn, replaced by a revised edition, or amended NOTE The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of publication A list of all parts of the IEC 60335 series, under the general title: Household and similar electrical appliances – Safety, can be found on the IEC website The following differences exist in the countries indicated below BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 –8– –5– – 6.1: Appliances may be of class 0I, if the rated voltage does not exceed 150 V (Japan) – 20.102: A 30 000 cycle endurance test is carried out on door interlocks (USA) – 25.7: The supply cord is required to have a free length of at least 1,5 m (USA) – Annex AA: The detergent and rinsing agent are different (USA) – Annex BB: Different tests are carried out (USA) BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 EN 60335-2-5:2015 – 14 – -6- In Table 3, delete the row “External enclosure of motor-operated appliances, except handles held in normal use” and the corresponding footnotes Add the following Table Z101 BS EN 60335-2-5:2015 Table Z101 – Maximum – 10 –temperature rises 60335-2-5 © IEC:2012 for external surfaces under normal operating conditions 10.1 Addition: a Surface Temperature rise K The selected representative period is the period during which the power input is the highest 10.2 Addition: Surfaces of appliances situated not more than 850 mm above the floor after installation Surfaces situated more than 850 mm above the floor after installation Front surfaces Other surfaces 40 45 45 11 Heating Coated metal 45 55 55 Glass and ceramic 55 60 60 Plastic and plastic c coating Replacement: > 0,3 mm 11.7 60 65 65 The selected representative period is the period during which the current is the highest Bare metal b This clause of Part is applicable except as follows a When the thickness of plastic coating does not exceed 0,3 mm, the temperature rise limits of coated metal or glass and ceramic applyincorporating a programmer or timer are operated for two cycles with the Appliances programme that results in the highest temperature rises The cycles are separated by a rest b Metal is considered coated when a coating having a minimum thickness of 80 µm made by enamel or non substantially period of 15 with the door or lid open plastic coating is used c The temperature riseare limit subjected applies also for a metal finish of thickness than instructions 0,1 mm Other appliances toplastic two material cycleshaving of the sequence stated less in the that results in the highest temperature rises or for two periods of 15 each, whichever is longer The cycles or periods are separated by a rest period of 15 with the door or lid open Add the following new subclause: Discharge pumps driven by a separate motor are then subjected to three periods of operation, each separated by a rest period of 15 The duration of each period of operation is 1,5 11.Z101 rises are not measured times the Temperature period necessary to empty the appliance when it is filled with the maximum quantity of water for which it is constructed The level of the water discharge is – on the underside of appliances intended to be used on a working surface or floor, – 90 cm above the floor, for appliances standing on the floor; – on the rear surface of appliances which, according to the instructions, shall be placed against a – the maximum height above the supporting surface, as stated in the instructions, for other wall appliances 12 20 Void Stability and mechanical hazards 20.102 Add the following at the end of the requirement: 13 Leakage current and electric strength at operating temperature When the door is opened, the programme cycle shall stop This clause of Part is applicable except as follows NOTE Z101 13.2 Draining is neglected Modification: For stationary class I appliances, the leakage current shall not exceed 3,5 mA, or mA/kW rated power input with a limit of mA, whichever is higher 14 Transient overvoltages This clause of Part is applicable 15 Moisture resistance This clause of Part is applicable except as follows 15.1 Addition: rated power input with a limit of mA, whichever is higher 14 Transient overvoltages – 15 – BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 This clause of Part is applicable 15 Moisture resistance This clause of Part is applicable except as follows 15.1 Addition: BS EN 60335-2-5:2015 Magnetic valves and similar components incorporated in external hoses for connection to the water mains subjected to the test specified for– IPX7 appliances 60335-2-5 © are IEC:2012 – 11 15.2 Replacement: Appliances shall be constructed so that spillage of liquid in normal use does not affect their electrical insulation, even if an inlet valve fails to close Compliance is checked by the following test Appliances with a type X attachment, except those having a specially prepared cord, are fitted with the lightest permissible type of flexible cord of the smallest cross-sectional area specified in Table 13 Appliances intended to be filled with water by the user are completely filled with water containing approximately % NaCl A further quantity of this solution equal to 15 % of the capacity of the appliance or 0,25 l, whichever is greater, is poured in steadily over a period of Other appliances are operated until the maximum water level is reached, and g of the detergent specified in Annex AA is added for each litre of water in the appliance The inlet valve is held open and the filling continued for 15 after first evidence of overflow or until the inflow is automatically stopped by other means For appliances that are loaded from the front, the door is then opened if this can be achieved manually and without damage to the door interlock system For appliances having a working surface, 0,5 l of water containing approximately % NaCl and 0,6 % of rinsing agent, as specified in Annex AA, is poured over the top of the appliance, the controls being placed in the on position The controls are then operated through their working range, this operation being repeated after a period of The appliance shall then withstand the electric strength test of 16.3 and inspection shall show that there is no trace of water on insulation that could result in a reduction of clearances and creepage distances below the values specified in Clause 29 15.101 Appliances shall be constructed so that foaming does not affect electrical insulation Compliance is checked by the following test which is carried out immediately after that of 15.2 The appliance is operated under the conditions specified in Clause 11 but for one complete cycle with the programme that results in the longest period of operation A solution consisting of 20 g of NaCl and ml of a solution of 28 % by mass of dodecyl sodium sulphate (C 12 H 25 Na SO ), is added for each l of water in the appliance The solution used for this test shall be stored in a cool atmosphere and used within seven days of its preparation For appliances incorporating a detergent dispenser, the solution is added manually at the point in the cycle when it would normally be dispensed automatically For other appliances, the solution is added before starting the cycle The appliance shall then withstand the electric strength test of 16.3 The appliance is then operated for two cycles under the same conditions, except that the (C 12 H 25 Na SO ), is added for each l of water in the appliance The solution used for this test shall be stored in a cool atmosphere and used within seven days of its preparation BS EN 60335-2-5:2015 – 16 – 60335-2-5 © IEC:2012 For appliances incorporating a detergent dispenser, the solution is added manually at the point in the cycle when it would normally be dispensed automatically For other appliances, the solution is added before starting the cycle The appliance shall then withstand the electric strength test of 16.3 The appliance is then operated for two cycles under the same conditions, except that the solution is not added It shall then withstand the electric strength test of 16.3 BS24 EN h60335-2-5:2015 The appliance is kept in a test room having a normal atmosphere for before being subjected to the test of 15.3 – 12 – 60335-2-5 © IEC:2012 16 Leakage current and electric strength This clause of Part is applicable 17 Overload protection of transformers and associated circuits This clause of Part is applicable 18 Endurance This clause of Part is not applicable 19 Abnormal operation This clause of Part is applicable except as follows 19.1 Addition: For appliances incorporating a programmer or timer, the tests of 19.2 and 19.3 are replaced by the test of 19.101 19.2 Addition: Restricted heat dissipation is obtained without water in the appliance or with just sufficient water to cover the heating elements, whichever is the more unfavourable 19.9 19.13 Not applicable Addition: During the tests of 19.101, the temperature of windings shall not exceed the values specified in Table 19.101 The appliance is supplied at rated voltage and operated under normal operation Any fault condition or unexpected operation that may be applied in normal use is introduced NOTE Examples of fault conditions and unexpected operations are – the programmer stopping in any position; – disconnection and reconnection of one or more phases of the supply during any part of the programme; – open-circuiting or short-circuiting of components; – failure of a magnetic valve; – opening and reclosing of the door or lid during any part of the programme, if this is possible; – failure or blocking of the mechanical part of a water level switch This fault condition is not applied if • the cross section of the tube supplying the air chamber with water is greater than cm with no dimension smaller than 10 mm; and • the outlet of the chamber is at least 20 mm above the highest water level; and • the tube connecting the air-chamber to the water level switch is fixed so that there is no likelihood of bending or pinching NOTE Examples of fault conditions and unexpected operations are – the programmer stopping in any position; – disconnection and reconnection of one or more phases the programme; – 17 of – the supply during any part of60335-2-5 © IEC:2012 – open-circuiting or short-circuiting of components; BS EN 60335-2-5:2015 – failure of a magnetic valve; – opening and reclosing of the door or lid during any part of the programme, if this is possible; – failure or blocking of the mechanical part of a water level switch This fault condition is not applied if EN 60335-2-5:2015 -6- • the cross section of the tube supplying the air chamber with water is greater than cm with no dimension smaller than 10 mm; and • the outlet of the chamber is at least 20 mm above the highest water level; and In Table 3, delete the row “External enclosure of motor-operated appliances, except handles held in • use” the tube the air-chamber to the water level switch is fixed so that there is no likelihood of normal and connecting the corresponding footnotes bending or pinching Add the following Table Z101 20 Stability and mechanical hazards BS EN 60335-2-5:2015 Table Z101 – Maximum temperature rises forisexternal surfaces normal operating conditions This clause©ofIEC:2012 Part applicable exceptunder as–follows 60335-2-5 13 – a Surface Temperature rise 20.1 BS EN Modification: 60335-2-5:2015 K 60335-2-5 © IEC:2012 – 13 – The appliance is empty Surfaces or filledofas specified for normal whichever is more more appliances situated not more operation, than Surfaces situated unfavourable Doors and lids and any castors turned to the most unfavourable 850are mmclosed above the floor after installation than 850 mm above the 20.1 Modification: position floor after installation Front surfaces Other surfaces The appliance is empty or filled Bare metal 40 as specified for normal 45 operation, whichever 45 is more Addition: unfavourable Doors and lids are closed and any castors turned to the most unfavourable b Coated metal 45 55 55 position For appliances that are loaded from the front, compliance is also checked by the test of Glass and ceramic 55 60 60 20.101 Addition: Plastic and plastic c 60 65 65 coating > 0,3 mm 20.101 The appliance is placed on a horizontal surface and a mass of 23 kg is placed on, or For appliances loaded from thedoor front, compliance is also checked by the istest of suspended from,that the are centre of the open or any fully opened drawer, whichever more a When the thickness of plastic coating does not exceed 0,3 mm, the temperature rise limits of coated metal or glass and 20.101 unfavourable Any castors are turned to the most unfavourable position ceramic apply b Metal isThe considered coated is when a coating aor minimum thickness of 80 madeofby23 enamel non substantially 20.101 appliance placed a horizontal surface and a µm mass kg isoraplaced on, or For appliances normally used onon a having table similar support and incorporating door having plastic coating is used suspended from, the of the rest openposition, door or aany fullyofopened whichever is more horizontal hinges andcentre a horizontal mass kg is drawer, used instead of a mass of c unfavourable Any castors are turned to the most unfavourable position 23 kg The temperature rise limit applies also for plastic material having a metal finish of thickness less than 0,1 mm For appliances normally used tableoror similar similar support support and having Appliances normally used on on a atable and incorporating which have a a door drawer are Add the following new subclause: horizontal hinges and a horizontal rest position, a mass of kg is used instead of a mass of additionally tested with the drawer placed in the most unfavourable position and loaded with 23 kg the maximum number of place settings in accordance with the instructions 11.Z101 Temperature rises are not measured Appliances normally used on a atable andwith which have a drawer If a dishwasher is combined with hob, or thesimilar test is support carried out the appliance loaded are as – on the undersidewith of appliances intended toinbethe used on aunfavourable working surface or floor,and loaded with additionally specified in tested IEC 60436, the the drawer point ofplaced application ofmost the mass being atposition the centre of the outer the maximum number settings in accordance with the instructions edge of the open door of or place drawer – on the rear surface of appliances which, according to the instructions, shall be placed against a wall If a dishwasher is combined The appliance shall not tilt with a hob, the test is carried out with the appliance loaded as specified in IEC 60436, the point of application of the mass being at the centre of the outer edge of the open door or drawer 20.102 Doors and shall be interlocked 20 Stability andlids mechanical hazards so that the appliance can only be operated when the door or lid is closed, unless there is adequate protection against ejection of hot water The appliance tilt when theAdd door orfollowing lid not is opened 20.102 theshall at the end of the requirement: and lids by shall be interlocked so that the 20.102 When theDoors door opened, theinspection programme cycle stop Compliance is ischecked and byshall manual test.appliance can only be operated when the door or lid is closed, unless there is adequate protection against ejection of hot water when the door or lid occurring is isopened after the door or lid has been opened is neglected NOTE Z101 Draining neglected NOTE Slight splashing immediately Compliance is checked by inspection and by manual test 21 Mechanical strength NOTE Slight splashing occurring immediately after the door or lid has been opened is neglected This clause of Part is applicable 21 Mechanical strength 22 Construction This clause of Part is applicable This clause of Part is applicable except as follows 22 Construction 22.6 Modification: This clause of Part is applicable except as follows NOTE Slight splashing occurring immediately after the door or lid has been opened is neglected BS EN 60335-2-5:2015 21 Mechanical strength 60335-2-5 © IEC:2012 – 18 – This clause of Part is applicable 22 Construction This clause of Part is applicable except as follows 22.6 Modification: BS EN 60335-2-5:2015 Instead of coloured water, a solution composed of 0,6 ml of the rinsing agent specified in 60335-2-5 © IEC:2012 Annex AA per litre of distilled water is used – 14 – Addition: Parts that withstand the ageing test specified in Annex BB are not considered to be parts where leakage could occur Drops of undiluted rinsing agent, as specified in Annex AA, are applied to the external surface of the parts from which rinsing agent could leak if a seal fails After the test, and taking into account opening and closing the door, if any, during the test there shall be no rinsing agent on the insulation of internal wiring or porous material in contact with the internal wiring, if deterioration of the insulation could result in a hazard 22.101 Appliances shall withstand the water pressure expected in normal use Compliance is checked by connecting the appliance to a water supply having a static pressure equal to twice the maximum permissible inlet water pressure or 1,2 MPa, whichever is higher, for a period of There shall be no leakage from any part, including the inlet water hose 22.102 Appliances shall be constructed so that heating elements cannot come into contact with combustible material inside the appliance as a result of deformation of the heating elements or of parts supporting them Compliance is checked by inspection 22.103 Appliances shall be constructed so that dishes and cutlery contacting heating elements during the drying period not give rise to a fire hazard Compliance is checked by the following test The appliance is placed on a piece of white pinewood board covered with tissue paper Polyethylene disks, approximately 80 mm in diameter and mm thick, are placed at the most unfavourable location, where possible directly in contact with the heating element The appliance is supplied at 1,1 times rated voltage and operated for a drying period under normal operation When smoke or odour is evident, or when one-third of the drying period has elapsed, whichever occurs first, the door or lid is opened Any flames, burning drops or glowing particles shall not spread fire to other parts of the appliance Flames, except from the disks, shall extinguish within 30 s of opening the door or lid The tissue paper shall not burn or the board become scorched The tissue paper shall comply with 4.215 of ISO 4046-4:2002 as thin, soft and strong lightweight wrapping tissue with a mass per unit area between 12 g/m and 30 g/m The material of the disks used for the test is to be unfilled natural colour polyethylene without flame-retardants and shall have a relative density of 0,96 ± 0,005 22.104 If the microenvironment is pollution degree the creepage distance along uncemented or unwelded joints in switches is considered to be zero Any flames, burning drops or glowing particles shall not spread fire to other parts of the appliance Flames, except from the disks, shall extinguish within 30 s ofBS opening the door or EN 60335-2-5:2015 lid The tissue paper shall not burn or the board become scorched – 19 – 60335-2-5 © IEC:2012 The tissue paper shall comply with 4.215 of ISO 4046-4:2002 as thin, soft and strong lightweight wrapping tissue with a mass per unit area between 12 g/m and 30 g/m The material of the disks used for the test is to be unfilled natural colour polyethylene without flame-retardants and shall have a relative density of 0,96 ± 0,005 22.104 If the microenvironment is pollution degree the creepage distance along uncemented or unwelded joints in switches is considered to be zero This requirement is not applicable to switches in low power circuits that are described in 19.11.1 BS EN 60335-2-5:2015 60335-2-5 ©isIEC:2012 – 15 – Compliance checked by inspection 23 Internal wiring This clause of Part is applicable except as follows 23.3 Modification: Instead of the test being carried out while the appliance is in operation, it is carried out with the appliance disconnected from the supply The number of flexings is increased to 100 000 Addition: After the test, not more than 10 % of the strands of any conductor of the internal wiring between the main part of the appliance and the door shall be broken 23.101 The insulation and sheath of internal wiring for the supply of magnetic valves and similar components incorporated in external hoses for connection to the water mains shall be at least equivalent to light polyvinyl chloride sheathed flexible cord (code designation 60227 IEC 52) Compliance is checked by inspection 24 Components This clause of Part is applicable except as follows 24.1.4 Addition: The number of cycles of operation for programmers is 000 The number of cycles of operation for door interlocks is 30 000 24.101 Thermal cut-outs incorporated in dishwashers for compliance with 19.4 shall not be self-resetting Compliance is checked by inspection 25 Supply connection and external flexible cords This clause of Part is applicable 26 Terminals for external conductors This clause of Part is applicable Compliance is checked by inspection BS EN 60335-2-5:2015 25 Supply connection and external flexible – 20 – cords 60335-2-5 © IEC:2012 This clause of Part is applicable 26 Terminals for external conductors This clause of Part is applicable 27 Provision for earthing This clause of Part is applicable – 16 – BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 28 Screws and connections This clause of Part is applicable 29 Clearances, creepage distances and solid insulation This clause of Part is applicable except as follows 29.2 Addition: The microenvironment is pollution degree 3, and the insulation shall have a CTI not less than 250, unless the insulation is enclosed or located so that it is unlikely to be exposed to pollution during normal use of the appliance due to – condensation produced by the appliance; – chemicals, such as detergent or rinse aid The requirement for a minimum CTI value of 250 is not applicable to functional insulation if the working voltage does not exceed 50 V 30 Resistance to heat and fire This clause of Part is applicable except as follows 30.2 Addition: For appliances incorporating a programmer or a timer, 30.2.3 is applicable For other appliances, 30.2.2 is applicable 31 Resistance to rusting This clause of Part is applicable 32 Radiation, toxicity and similar hazards This clause of Part is applicable BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 – 21 – BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 – 17 – Annexes The annexes of Part are applicable except as follows Annex AA (normative) Detergent and rinsing agent AA.1 Detergent The composition of the detergent is given in Table AA.1: Table AA.1 – Detergent composition Substance Parts by mass % Penta-sodiumtriphosphate ("Tripoly") Thermphos NW 50,00 Sodium metasilicate KO (anhydrous) 40,00 Sodium sulphate (anhydrous) 5,75 Sodium dichlorisocyanurate-dihydrate CDB 56 C 2,25 Plurafac RA 43 2,00 Plurafac RA 43 is the trade name of a product supplied by BASF This information is given for the convenience of users of this International Standard and does not constitute an endorsement by IEC of this product The plurafac RA 43 is thoroughly mixed with the silicate and sulphate The sodium dichlorisocyanurate-dihydrate is mixed into the phosphate The two are then thoroughly mixed together The detergent should be stored in a cool atmosphere in a waterproof bag in quantities not exceeding kg It should be used within three months AA.2 Rinsing agent The composition of the rinsing agent is given in Table AA.2: Table AA.2 – Rinsing agent composition Substance Parts by mass % Plurafac LF 221 15,0 Cumene sulfonate (40 % solution) 11,5 Citric acid (anhydrous) 3,0 Deionized water 70,5 Plurafac LF 221 is the trade name of a product supplied by BASF This information is given for the convenience of users of this International Standard and does not constitute an endorsement by IEC of this product BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 – 22 – – 18 – BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 The rinsing agent has the following properties: • viscosity, 17 mPa⋅s; • pH, 2,2 (1 % in water) Any commercially available rinsing agent may be used, but if there is any doubt with regards to the test results, this composition is to be used – 23 – BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 – 19 – Annex BB (normative) Ageing test for elastomeric parts The ageing test on elastomeric parts is carried out by measuring their hardness and mass before and after immersion in solutions of detergent and rinsing agent at elevated temperature The test is carried out on at least three samples of each part The test procedure is as specified in ISO 1817, with the following modifications Test liquids Two test liquids are used: – one liquid is obtained by dissolving g of the detergent specified in Annex AA per litre of distilled water; – the other liquid is composed of 0,6 ml of rinsing agent as specified in Annex AA per litre of distilled water Care is to be taken to ensure that the total mass of the test pieces immersed does not exceed 100 g for each litre of solution, that the test pieces are completely immersed and that their entire surface is freely exposed to the solution During the tests, the test pieces are not to be exposed to direct light Test pieces of different compounds are not to be immersed at the same time in the same solution 6.4 Test pieces Conditioning The temperature is 23 °C ± °C and the relative humidity is (50 ± 5) % 7.1 Immersion in the test liquid Temperature The solution is heated within h with the test pieces immersed, to a temperature of 75 +5 °C and maintained at this value The solution is renewed every 24 h and heated in the same way NOTE To avoid undue evaporation of the solution, a closed-circuit system or similar method can be used for renewing the solution 7.2 Duration The test pieces are immersed for a total period of 48 +10 h The test pieces are then immediately immersed in a fresh solution, which is maintained at ambient temperature The pieces are immersed for 45 ± 15 After having been removed from the solution, the test pieces are rinsed in cold water at 15 °C ± °C and then dried with blotting paper BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 – 24 – – 20 – 8.2 BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 Procedure Change in mass The increase in mass of the test pieces shall not exceed 10 % of the value determined before immersion 8.6 Change in hardness The micro-test for hardness applies The hardness of the test pieces shall not have changed by more than IRHD Their surface shall not have become sticky and shall show no crack visible to the naked eye or any other deterioration – 25 – BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 BS EN 60335-2-5:2015 60335-2-5 © IEC:2012 – 21 – Bibliography The bibliography of Part is applicable except as follows Addition: IEC 60335-2-58, Household and similar electrical appliances – Safety – Part 2-58: Particular requirements for commercial electric dishwashing machines NOTE Harmonized as EN 60335-2-58 _ This page deliberately left blank This page deliberately left blank NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW British Standards Institution (BSI) BSI is the national body responsible for preparing British Standards and other standards-related publications, information and services BSI is incorporated by Royal Charter British Standards and other standardization products are published by BSI Standards Limited About us Revisions We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions Our British Standards and other publications are updated by amendment or revision The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process Organizations of all sizes and across all sectors choose standards to help them achieve their goals Information on standards We can provide you with the knowledge that your organization needs to succeed Find out more about British Standards by visiting our website at bsigroup.com/standards or contacting our Customer Services team or Knowledge Centre Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at bsigroup.com/shop, where hard copies can also be purchased If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team Subscriptions Our range of subscription services are designed to make using standards easier for you For further information on our subscription products go to bsigroup.com/subscriptions With British Standards Online (BSOL) you’ll have instant access to over 55,000 British and adopted European and international standards from your desktop It’s available 24/7 and is refreshed daily so you’ll always be up to date You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member PLUS is an updating service exclusive to BSI Subscribing Members You will automatically receive the latest hard copy of your standards when they’re revised or replaced To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit bsigroup.com/shop With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet Licences can cover as few or as many users as you wish With updates supplied as soon as they’re available, you can be sure your documentation is current For further information, email bsmusales@bsigroup.com BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK We continually improve the quality of our products and services to benefit your business If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre Copyright All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means – electronic, photocopying, recording or otherwise – without prior written permission from BSI Details and advice can be obtained from the Copyright & Licensing Department Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): orders@bsigroup.com Email (enquiries): cservices@bsigroup.com Subscriptions Tel: +44 845 086 9001 Email: subscriptions@bsigroup.com Knowledge Centre Tel: +44 20 8996 7004 Email: knowledgecentre@bsigroup.com Copyright & Licensing Tel: +44 20 8996 7070 Email: copyright@bsigroup.com