Tiêu chuẩn iso ts 15143 3 2016

TECHNICAL SPECIFICATION ISO/TS 15143-3 First edition 2016-12-01 Earth-moving machinery and mobile road construction machinery — Worksite data exchange — Part 3: Telematics data Engins de terrassement et machines mobiles de construction de routes — Échange de données sur le chantier — Partie 3: Données télématiques Reference number ISO/TS 15143-3:2016(E) I n tern ati o n al Org an i z ati o n fo r S tan d ard i z ati o n © ISO 2016 ISO/TS 15143-3:2016(E) COPYRIGHT PROTECTED DOCUMENT © ISO 2016, Published in Switzerland All rights reserved Unless otherwise specified, no part o f this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission Permission can be requested from either ISO at the address below or ISO’s member body in the country o f the requester ISO copyright o ffice Ch de Blandonnet • CP 401 CH-1214 Vernier, Geneva, Switzerland Tel +41 22 749 01 11 Fax +41 22 749 09 47 copyright@iso.org www.iso.org ii I n tern ati o n al Org an i z ati o n fo r S tan d ard i z ati o n ISO/TS 15143-3:2016(E) Contents Page Foreword vii Introduction viii Scope Normative references Terms, definitions and abbreviated terms Data management and access control Response formats 4.1 4.2 4.3 4.4 4.5 XML Declaration links to definition segments Paging Discoverability 8.1 8.2 8.3 8.4 10 11 Minimum requesting period Editing the data elements over time Data element use case Data element cross reference Access authentication General Snapshot endpoint 8.2.1 Fleet snapshot 8.2.2 Single-element snapshot Time series endpoint 8.3.1 General Links 8.4.1 Reference attribute (rel) 8.4.2 Hypermedia re ference URL (hre f) Date and time formats Data fields summary 10 Data field descriptions 12 11.1 General 12 11.2 Machine header information 13 11.2.1 General 13 11.2.2 Telematics unit installation date 13 11.2.3 Equipment make 13 11.2.4 Equipment model 13 11.2.5 Equipment ID 13 11.2.6 Serial Number 13 11.2 OEM ISO Identifier (PIN or VIN) 13 11.3 Last known location 14 11.3.1 General 14 11.3.2 Date and time of location 14 11.3.3 Latitude of location 14 11.3.4 Longitude of location 14 11.3.5 Altitude of location 14 11.3.6 Unit of measure of altitude 14 11.3.7 Location Time Series Endpoint (Request) 14 11.3.8 Location Response Schema (Response) 15 11.4 Operating hours 15 11.4.1 General 15 11.4.2 Date and time of operating hours 15 11.4.3 Operating hours 15 11.4.4 Operating hours endpoint (Request) 15 © ISO 2016 – All rights reserved iii I n tern ati o n al Org an i z ati o n fo r S tan d ard i z ati o n ISO/TS 15143-3:2016(E) 11.4.5 Operating hours schema (Response) 16 Cumulative fuel used (preferred) 16 11.5.1 General 16 11.5.2 Date and time of cumulative fuel used 16 11.5.3 Unit of measure of fuel used to date 16 11.5.4 Amount of fuel used to date 16 11.5.5 Cumulative fuel used endpoint (Request) 17 11.5.6 Cumulative fuel used schema (Response) 17 11.6 Fuel used in the preceding 24 hours (alternative, not preferred) 17 11.6.1 General 17 11.6.2 Date and time of fuel use in the preceding 24 hours 17 11.6.3 Unit of measure of fuel used in the preceding 24 hours 18 11.6.4 Fuel used in the preceding 24 hours 18 11.6.5 Fuel used in the preceding 24 hours endpoint (Request) 18 11.6.6 Fuel used in the preceding 24 hours schema (response) 18 11.7 Cumulative distance travelled 18 11.7.1 General 18 11.7.2 Date and time of distance 19 11.7.3 Unit of measure of distance 19 11.7.4 Cumulative distance travelled 19 11.7.5 Cumulative distance travelled endpoint (Request) 19 11.7.6 Cumulative distance travelled schema (response) 19 11.8 Caution codes referencing number 20 11.8.1 General 20 11.8.2 Date and time of code 20 f 20 11.8.4 Code description 20 11.8.5 Caution codes referencing number endpoint (Request) 20 11.8.6 Caution codes referencing number schema (response) 20 11.9 Cumulative idle operating hours 21 11.9.1 General 21 11.9.2 Date and time of cumulative idle operating hours 21 11.9.3 Cumulative idle operating hours 21 11.9.4 Cumulative idle operating hours endpoint (Request) 21 11.9.5 Cumulative idle operating hours schema (response) 22 11.10 Fuel remaining ratio 22 11.10.1 General 22 11.10.2 Date and time of percent fuel remaining 22 11.10.3 Fuel Remaining Ratio 22 f f f 22 22 11.10.6 Fuel remaining ratio endpoint (Request) 23 11.10.7 Fuel remaining ratio schema (response) 23 11.11 Percent of DEF remaining 23 11.11.1 General 23 11.11.2 Date and time of percent DEF remaining 23 11.11.3 Percent of DEF remaining 23 f f 24 24 11.11.6 Percent DEF remaining endpoint (Request) 24 11.11.7 Percent DEF remaining schema (response) 24 11.12 Engine condition 24 11.12.1 General 24 11.12.2 Date and time of engine condition 25 11.12.3 Engine Number 25 11.12.4 Engine condition 25 11.12.5 Engine condition endpoint (Request) 25 11.12.6 Engine condition schema (response) 25 11.5 iv 1 8.3 I E C /I S O Symb o l Re erence N umb er identifier 1 0.4 Unit o 1 0.5 Fuel tank cap acity 1 1 Unit o 1 1 D E F tank cap acity I n tern ati o n al Org an i z ati o n fo r S tan d ard i z ati o n meas ure meas ure or uel tank cap acity o r D E F tank cap acity ISO/TS 15143-3:2016(E) 11.13 Digital input state 25 11.13.1 General 25 11.13.2 Date and time of digital input set response 26 11.13.3 Digital input number 26 11.13.4 1Digital input state 26 11.13.5 Digital input state endpoint (Request) 26 11.13.6 Digital input state schema (response) 26 11.14 Cumulative power takeoff hours 27 11.14.1 General 27 11.14.2 Date and time of cumulative power takeoff 27 11.14.3 Cumulative power takeoff hours 27 11.14.4 Cumulative power takeoff hours endpoint (Request) 27 11.14.5 Cumulative power takeoff hours schema (response) 27 11.15 Average daily engine load factor 28 11.15.1 General 28 11.15.2 Date and time of average load factor 28 11.15.3 Average load factor for preceding 24 hour period 28 11.15.4 Average daily engine load factor endpoint (Request) 28 11.15.5 Average daily engine load factor schema (response) 28 11.16 Peak daily speed 29 11.16.1 General 29 11.16.2 Date and time of peak travel speed 29 11.16.3 Units of measure for speed 29 11.16.4 Peak speed for the preceding 24 h 29 11.16.5 Peak daily speed endpoint (Request) 29 11.16.6 Peak daily speed schema (response) 29 11.17 Cumulative load count 30 11.17.1 General 30 11.17.2 Date and time of load count 30 11.17.3 Cumulative load count 30 11.17.4 Cumulative load count endpoint (Request) 30 11.17.5 Cumulative load count schema (response) 30 11.18 Cumulative payload total 31 11.18.1 General 31 11.18.2 Date and time o f cumulative payload 31 11.18.3 Unit o f measure for payload 31 11.18.4 Cumulative payload 31 11.18.5 Cumulative payload total endpoint (Request) 31 11.18.6 Cumulative payload total schema (response) 31 11.19 Cumulative non-productive regeneration hours 32 11.19.1 General 32 11.19.2 Date and time for cumulative non-productive regeneration hours 32 11.19.3 Cumulative non-productive regeneration hours 32 11.19.4 Cumulative hours in non-productive regeneration endpoint (Request) 32 11.19.5 Cumulative hours in non-productive regeneration schema (response) 33 11.20 Cumulative idle non-operating hours 33 11.20.1 General 33 11.20.2 Date and time of cumulative idle nonoperating hours 33 11.20.3 Cumulative idle non-operating hours 33 11.20.4 Cumulative idle non-operating hours endpoint (Request) 33 11.20.5 Cumulative idle non-operating hours schema (response) 34 11.21 Data field descriptions for codes unique to each system 34 11.21.1 General 34 11.21.2 Diagnostic Trouble Code identifier 34 11.21.3 Date and time of code 35 11.21.4 Code severity 35 11.21.5 Code description 35 11.21.6 Unit of measure for ambient air temperature 35 © ISO 2016 – All rights reserved I n tern ati o n al Org an i z ati o n fo r S tan d ard i z ati o n v ISO/TS 15143-3:2016(E) 11.21.7 Ambient air temperature at time when code was triggered 35 11.21.8 Description of code source 35 1 D ata field des crip tio ns fo r co des unique to each sys tem endp o int (Reques t) 36 11.21.10 D ata field des crip tio ns fo r co des unique to each sys tem s chema (res p o ns e) 36 12 Data schemas 36 13 Syntax errors 36 12.1 12.2 Common schema 36 Time series schema 36 Annex A (informative) Relationship between this document and ISO 15143-2 38 Annex B (informative) Data support and collection 54 Annex C (informative) Common schema 55 Annex D (informative) Time series schema 59 Bibliography 60 vi I n tern ati o n al Org an i z ati o n fo r S tan d ard i z ati o n ISO/TS 15143-3:2016(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies) The work o f preparing International Standards is normally carried out through ISO technical committees Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters o f electrotechnical standardization The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part In particular the different approval criteria needed for the di fferent types o f ISO documents should be noted This document was dra fted in accordance with the editorial rules of the ISO/IEC Directives, Part (see www.iso.org/directives) Attention is drawn to the possibility that some o f the elements o f this document may be the subject o f patent rights ISO shall not be held responsible for identi fying any or all such patent rights Details o f any patent rights identified during the development o f the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents) Any trade name used in this document is in formation given for the convenience o f users and does not constitute an endorsement For an explanation on the meaning o f ISO specific terms and expressions related to formity assessment, as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html The committee responsible for this document is Technical Committee ISO/TC 127, Earth-moving machinery, Subcommittee SC 3, Machine characteristics, electrical and electronic systems, operation and maintenance This part o f ISO 15143 is intended to be used in conjunction with ISO 15143-1 and ISO 15143-2 A list of all parts in the ISO 15143 series can be found on the ISO website © ISO 2016 – All rights reserved I n tern ati o n al Org an i z ati o n fo r S tan d ard i z ati o n vii ISO/TS 15143-3:2016(E) Introduction This document is a data schema having the purpose o f providing data directly from the equipment manufac turer or provider to the equipment owner in a s tandardi zed format for the use and convenience o f equipment owners with mixed fleets o f equipment It defines a set o f web services that provide in formation about fleets o f mobile equipment and their associated telematics data The in formation about a fleet is provided as a resource, typically on the Internet, at a known Uni form Resource Location (URL) Any number o f fleets can be represented, each with its own URL Clients can access these resources by sending HTTPS GET requests to the server at the given location The server responds with an equipment in formation document whose vocabulary is defined in this cument I SO/ TC 7/SC wishes to acknowledge the As so ciation of E quipment M anufac turers and the As sociation of E quipment M anagement P rofes s ional s for their contributions to prior work on this subject The goal o f this document is to provide direct access by end users to their specific fleet data, and not to enable third p ar ties for data aggregation acros s end users or other purp oses T he use of this document enables each end user or assigned third-party application developer to develop applications for purposes deemed appropriate by the end user viii I n tern ati o n al Org an i z ati o n fo r S tan d ard i z ati o n TECHNICAL SPECIFICATION ISO/TS 15143-3:2016(E) Earth-moving machinery and mobile road construction machinery — Worksite data exchange — Part 3: Telematics data Scope T h i s c u ment s p e ci fie s the com mun ic ation s chema de s igne d to provide mobi le mach i ner y s tatu s data from a telematic s provider ’s s er ver to th i rd-p ar ty cl ient appl ic ation s vi a the I nterne t T he data are collected from a mobile machine using telematics data-logging equipment and stored on a telematics provider’s server This document describes the communications records used to request data from the f of machine performance and health s er ver and the re s p on s e s rom the s er ver conta i ni ng s p e ci fie d data elements to b e u s e d i n the a na lys i s I t i s appl ic able to mobi le e ar th-movi ng mach i ner y a s defi ne d i n I S O 6165 and mobi le ro ad s tr uc tion mach i ner y a s defi ne d i n I S O 2 42 e qu ipp e d with lo c ation and ti me i n s tr u mentation It is not applicable to the on-board data collection, on-board communication protocol (e.g CANbus) or after the data have been collected at the data logger See Figure wi rele s s tra n s m i s s ion o f the mobi le mach i ner y data to the telematics provider ’s s er ver F i g u r e — T o p o g r a p h y o f c o n c e p t u a l m i x e d f l e e t t e l e m a t i c s s y s t e m within the scope of this document © ISO 2016 – All rights reserved I n tern ati o n al Org an i z ati o n fo r S tan d ard i z ati o n ISO/TS 15143-3:2016(E) Normative references T he fol lowi ng c u ments are re ferre d to i n the te xt i n s uch a way that s ome or a l l o f thei r content s titute s re qu i rements o f th i s c u ment For date d re ference s , on ly the e d ition c ite d appl ie s For undate d re ference s , the l ate s t e d ition o f the re ference d c u ment (i nclud i ng a ny amend ments) appl ie s I SO 779, Road vehicles — Vehicle identification number (VIN) — Content and structure Earth-moving machinery — Symbols for operator controls and other displays — Part 1: Common symbols I SO 40 -1 , I SO 40 -2 , Earth-moving machinery — Symbols for operator controls and other displays — Part 2: Specific symbols for machines, equipment and accessories I SO 01 , and times Data elements and interchange formats — In formation interchange — Representation of dates I SO 102 61 , Earth-moving machinery — Product identification numbering system Earth-moving machinery and mobile road construction machinery — Worksite data exchange — Part 1: System architecture I SO 5143 -1 : 010 , I SO 5143 -2 : 010 , Earth-moving machinery and mobile road construction machinery — Worksite data exchange — Part 2: Data dictionary EC M A- 40 4, The JSON Data Interchange Format I E TFRFC 72 , Hypertext Transfer Protocol (HTTP/1.1): Semantics and Context Terms, definitions and abbreviated terms Fo r the purposes o f th i s c u ment, the fo l lo wi n g ter m s , de fi n itio n s a nd ab b re vi ate d ter m s (s e e Tab le ) ap p l y I SO and I E C maintain terminological datab ases for us e in s tandardiz ation at the fol lowing addres ses: — I SO O n l ine brows ing platform: avai lable at http://www iso org/obp — I E C E lec trop edia: avai lable at http://www elec trop edia org/ 3.1 caution codes referencing number I S O/I E C s ymb ol regi s tration nu mb er a s defi ne d i n I S O 70 0 and re ference d i n I S O -1 N o te to entr y: C aution co de s re ferenc i ng nu mb ers a re re tu r ne d fro m the telem atic s p rovider s er ver a nd re fer to s ta nda rd i z e d s ymb ol s repre s enti n g va r iou s co nd ition s pre s ent o n E M M 3.2 construction worksite lo c ation o f the op eration o f a fle e t o f mobi le e qu ipment genera l ly identi fie d as s truc tion mach i ne s where the machines are used to p erform work 3.3 data element i n s ta nce o f data tran s m itte d by the OE M s er ver to the th i rd-p ar ty appl ic ation ad heri ng to the defi n ition o f the quantity or cond ition de s crib e d b y C lause 11 of this cument 3.4 discoverability re qu i rement that the data b e s tore d i n s uch a man ner that it c a n b e acce s s e d i f ne ce s s ar y I n tern ati o n al Org an i z ati o n fo r S tan d ard i z ati o n This document ISO 15143-2:2010 This document ISO 15143-2:2010 Tab le A Section Data element name scheme item value C l a s s i f i c a t i o n Data element concept name Use case Time stamp Tab le A Name Example Unit Range V a l u e d o m a i n Produc- Health tivity 1 19 C u mu l ative X Real time Processed time X no n-pro duc tive re generation hou rs http: //s ta nd ard s i s o org/i s o/1 5143/-3/C u mu l ati veN onpro duc tiveRe generatio nH ou rs xs d 1 19 D ate a nd ti me m ac h i ne _r u n - m ach i ne _r u n - m ach i ne _r u n - –1 –3 Y Y Y Y_M M _ of c u mu l ative n i n g _ s tate n i n g _d ate _ a nd _ n i ng _d ate _ a nd _ T2 : 4: Z DDTHH _ ti me ti me _2 C u mu l ati ve id le _no no p e rat- id le _no no p erat- id le nono p er- i n g _ho u r s i ng _o u r s _1 no n-pro duc- d ate ti me _ M M _S SZ tive re generatio n hou rs 1 19 3 4, D ecimal ti me _ HHHH hh ati ng hou rs 1 C u mu l ati ve id le X no nop erati ng hou rs http: //s ta nd ard s i s o org/i s o/1 5143/-3/C u mu l ati veI d l eN o nop erati ngH ou rs xs d 11 20 D ate a nd ti me m ach i ne _wo rk- m ach i ne _wo rk- m ach i ne _wo rk- –1 –3 Y Y Y Y_M M _ of c u mu l ative i n g _ s tate i n g _d ate _ a nd _ i ng _d ate _ a nd _ T 2 : 4: Z DD TH H _ ti me ti me _2 C u mu l ati ve id le _no no p e rat- id le _o p e rati n g - id le nono p er- i n g _ho u r s ho u rs _1 id le nono p er- d ate ti me _ M M _S SZ ati ng hou rs 11 20 ati ng hou rs 4, D ecimal HHHH hh ti me _ X ISO/TS 15143-3:2016(E) 48 I n tern ati o n al Org an i z ati o n fo r S tan d ard i z ati o n Table A.1 (continued) © ISO 2016 – All rights reserved I n tern ati o n al Org an i z ati o n fo r S tan d ard i z ati o n Table A.1 (continued) This document ISO 15143-2:2010 This document Table A.1 Section Data element name scheme item value C l a s s i f i c a t i o n Data element concept name Name Example Unit ISO 15143-2:2010 Table A.2 Range V a l u e d o m a i Use case Produc- Health tivity n 11.21 scriptions for codes X D ata fie ld de Time stamp Real time Processed time X u n ique to e ach s ys tem http://standards.iso.org/iso/15143/-3/FaultCode.xsd 11.21.2 Diagnostic Trouble Code m ach i ne _r u n ac ti ve _tro u ac ti ve _tro ub le _ n i n g _ s tate b le _co de co de _1 523865.9 Numeric string unbounded - co de _ a lp h a nu me t r ic _1 ide nti fie r 11.21.3 Date and time of code 11.21.4 C o de s e ver i t y m ach i ne _r u n - m ach i ne _r u n time tro ub le _c o de _ s e - tro ub le _c o de _de scripton T 2 : 4: Z ti me _ ve r i t y 11.21.5 Code description 2015–12–31 - n i ng _d ate _ a nd _ n i n g _d ate _ a nd _ tro ub le _co de _ s e Y Y Y Y_M M _ d ate ti me _ DD TH H _ M M _S SZ - INFO string unbounded - INFO OC3 string 523865.09 The SSM has lost CAN communication with the VCU unbounded co de _ch a rac ter_1 ver i t y_1 - tro ub le _co de _de s c r ip to n _1 co de _ch a rac ter_1 ISO/TS 15143-3:2016(E) 49 This document ISO 15143-2:2010 This document ISO 15143-2:2010 Tab le A Section Data element name scheme item value C 11 21 l a s s i f i c a t i o Un it of m ach i ne _r u n - me as u re for n i n g _ s tate n Data element concept name Name Example Unit Range V a l u e d o m a i n C el s iu s s tr i ng ↓ 34 I nteger −1 0 to +10 ce l s iu s _temp e - amb ient a i r temp eratu re 1 Amb ient Ai r a mb ie nt _a i r_te m - a mb ie nt _ a i r_tem - temp eratu re p eratu re p e ratu re _2 D TC _s o u rce D TC _ s o u rce _1 tu re _2 of ti me when co de wa s tr i ggere d 11 21 D e s c r ip tion of b a s ic _m ach i ne _ co de s o u rce d ata Use case Time stamp Tab le A TBD co de _ch a rac ter_1 Produc- Health tivity Real time Processed time ISO/TS 15143-3:2016(E) 50 I n tern ati o n al Org an i z ati o n fo r S tan d ard i z ati o n Table A.1 (continued) ISO/TS 15143-3:2016(E) A.2 Data element use cases for T he u s e c a s e e ach o f the data elements identi fie d i n i n th i s c u ment c a n b e found in Table A.2 Table A.2 — Data element use cases Section Who uses the data? Site manager Machine (Productivity) manager (Health) 11.2 Machine header information 11.2 Telematics unit installation date x x x How are the data used? ISO I5143-1:2010 Table List of sub-services Data usage scenarios T he s e d ata a re u s e d b y the th i rd-p a r ty ap p l ic atio n to identi fy the d ata element through the data schema Construction management Construction when the telematics unit was installed management of manufacture of the machine For a third T he s e d ata a re u s e d to fi r m the d ate For the O E M , th i s date i s p o s s ib l y the d ate p a r ty telem atic s pro vider th i s date i s p o s s ib l y the d ate o f the i n s ta l l atio n o f the x 11.2 Equipment make x re tro fitte d de vice Construction of the machine I can be used to plan and management T he s e data a re u s e d to identi fy the O E M track m ach i ne uti l i z ation b y O E M x 11.2 Equipment model x 11.2.5 Equipment I D ( i d e n t i f i c a t i o x for m i xe d fle e ts f Construction machine form, size and model of the ma- management chine It can be used to plan utilization of the machine for a particular task Construction f management T he s e data a re u s e d to identi y the E qu ip ment I D (identi fic ation) i s u s e d to identi y a p a r tic u l a r m ach i ne I t i s a s n ) s igne d b y the m ach i ne owner o r end u s er I t i s u s e d to track m ach i ne uti l i z ation b y x 11.2.6 Serial number x s p e c i fic m ach i ne Construction management when a PIN or VIN is not available It is intended to extend the application of Part to machines other than EMM or mobile T he s e data a re u s e d to identi fy a p a r tic u l a r m ach i ne I t i s a s s igne d b y a n O E M ro ad s tr uc tio n m ach i ner y I t i s u s e d to track m ach i ne uti l i z atio n b y s p e c i fic 11.2.7 Product I d e n t i f i c a t i o n x x number (PIN) or cation number v e ( h V I i c N l e i d e n t i machine Construction the machine It is used to to track machine management T h i s 17 ch a rac ter field u n iquel y identi fie s uti l i z ation b y s p e c i fic m ach i ne f i ) 11.3 Last known location x 11.4 Operating hours x Equipment and Latitude, Longitude and Elevation are used to plot the machine location on a map to plan service routes for fueling, greasing, etc Other uses include geofencing and theft alarms The hour meter value on the machine is Equipment and used to schedule servicing and to monitor the utilization of the machine I denti fy the m ach i ne lo c ation s upp l y © ISO 2016 – All rights reserved I n tern ati o n al Org an i z ati o n fo r S tan d ard i z ati o n x x s upp l y 51 ISO/TS 15143-3:2016(E) Table A.2 (continued) Section 11.5 Cumulative fuel used Who uses the data? Site manager Machine (Productivity) manager (Health) x x How are the data used? ISO I5143-1:2010 Table List of sub-services Data usage scenarios T he cu mu lative fuel u s e i s us ed to mon- E quipment a nd itor the co s ts o f the s upp l y fuel u s e d b y the m a - ch i ne and to comp are that co s ts to s i m i lar mach i nes 11.6 Fuel used in the preceding 24 hours 11.7 Cumulative distance travelled x T he fuel u s ed i n the las t hou rs i s u s ed E qu ipment and to account for the co s t of the fuel and to s upp l y a n a l ys e the uti l i z ation o f the m ach i nel x x To identi fy the s er vice ti m i ng (i e tyre E quipment a nd change) s upp l y – C u s to mer cou ld re view h i s tor y o f m a ch i ne s to s e e how m a ny ki lome tre s trav- el led, to help plan mai ntenance or res a le – Tyre rep l acement p l a n n i n g – Typic a l l y d i s ta nce travel le d i s me a s u re d us i ng an on b o ard o dome ter 11.8 Caution codes referencing number x x T he caution co des referenci ng numb ers E quipment a nd a re u s e d to identi fy the op erati n g he a lth s upp l y o f s p e c i fic s ub s ys tem s on the m ach i ne Fau lt co des are an indic ator of comp o nents op erati ng out of tolerance or fa i lure D ep end i n g up o n the s e ver ity, s er vice a nd p a r ts m ay b e re qu i re d 11.9 Cumulative idle operating hours x Id le op erati ng hours are an i nd ic ation of E qu ipment and the uti l i z ation o f the m ach i ne a nd m ay s upp l y b e us ed to en force works ite op erationa l p ol icies i ntended to reduce fuel u s age 11.10 Fuel remaining ratio x T he fuel remain i ng ratio i n the fuel tan k i s u s e d to s che du le fuel del iver y to the E qu ipment and s upp l y mach i ne 11.11 Def remaining ratio 11.12 Engine condition x x T he p ercent of DE F remai ni ng i s us e d to E qu ipment and s che du le D E F del iver y to the veh icle s upp l y T he pro duction manager could compile M ach i ne co n- the time the engine was running and use s tr uc tio n that to evaluate an op erator A produc tion manager cou ld identi fy when mach ine s are operated outs ide of normal working hours 11.13 Digital input state x x G enera l l y, telem atic s u n its fe atu re unas- s igned d igita l i nputs that can b e us ed to E quipment a nd s upp l y tran s m it the s tatu s of d i s crete s ens ors i ns ta l led on the mach ine E xamples i nclude pres s ure and temp erature s witches , i nterlo ck s witche s , proxi m ity p o s ition s ens ors and the l i ke 11.14 Cumulative power takeoff hours x x T he pro duc tion ma nager cou ld compi le M ach i ne co n- the time the p ower ta ke off wa s drivi ng s tr uc tio n a n i mp lement s uch a s a mower or s pray- er or s ite d rainage pump T he s er vice manager u s es the p ower take off u s age to s chedu le preventative mai ntenance on the i mplement 52 I n tern ati o n al Org an i z ati o n fo r S tan d ard i z ati o n ISO/TS 15143-3:2016(E) Table A.2 (continued) Section Who uses the data? Site manager Machine (Productivity) manager (Health) 11.15 Average daily load factor x x How are the data used? ISO I5143-1:2010 Table List of sub-services Data usage scenarios T he average da i l y lo ad fac tor i s u s e d to o p ti m i z e m ach i ne s i z e a nd c ap ac ity to identi fy m ach i ne s that a re u nder or over x 11.16 Peak daily speed 11.17 Cumulative load count loaded Machine conmonitor excessive machine speed to iden- struction T he p e a k da i l y travel s p e e d i s u s e d to ti fy m ach i ne m i s u s e or u nder u s e x T he c u mu l ative lo ad co u nt i s u s e d b y the production manager to monitor the numf f over a given period b er o 11.18 Cumulative payload total x For m ach i ne s with p aylo ad mo n itor i ng s ys tem s i n s ta l le d , the pro duc tion m a n D a t a f i e l d x x Equipment and s upp l y c ycle s p er o rme d b y the m ach i ne ager mon ito rs the to ta l p aylo ad l i fte d , 11.19 Cumulative non-productive regeneration hours 11.20 Cumulative idle non-operating hours 11.21 descriptions for codes unique to each system Machine construction - Equipment and s upp l y h au le d o r pro ce s s e d b y the m ach i ne The production manager can monitor the Machine contime spent operating the exhaust regen- struction eratio n s ys tem o n m ach i ne s fitte d with a fter tre atment s ys tem s x x The production manager can monitor the time spent with the unit idling in a non-productive state The fault code can alert the owner to the need for non-scheduled machine support, f f machine Fault codes are an indicator of components operating out of tolerance Machine construction Machine construction a nd m ay b e u s e d to identi y the o p erat i ng he a lth o or fa i lu re s p e c i fic s ub s ys tem s on the D ep end i n g up o n the s e ver ity, s er vice a nd p a r ts m ay b e re qu i re d © ISO 2016 – All rights reserved I n tern ati o n al Org an i z ati o n fo r S tan d ard i z ati o n 53 ISO/TS 15143-3:2016(E) Annex B (informative) Data support and collection An OEM or third-party provider need not supply all data elements defined in this document, several o f which are identified as optional Not all the data points identified are necessarily received by the third-party application or the end user and not all data collected by the OEM or third-party provider are provided directly to the customer The OEM or third-party provider provides data as it deems appropriate Data collected according to this document may be collected by third-party retrofit telematics systems operating with servers provided as part o f the telematics system and those third-party systems may be operated completely independently o f the OEM 54 I n tern ati o n al Org an i z ati o n fo r S tan d ard i z ati o n ISO/TS 15143-3:2016(E) Annex C (informative) Common schema The common schema can be accessed at the URN: http://standards.iso.org/iso/15143/-3/common.xsd The developer is encouraged to access the schema from this location to ensure the use of the most upto-date version of the schema