I NTERNATI ONAL STAN DARD I S0 2336 1 Fi rst edi ti on 1 996 04 01 ANSI I ntemat Dot Set Hacksaw bl ades Part 1 Di mensi ons for hand bl ades Lames de sti es droi tes 2 mktaux Parti e 1 Di mensi ons d[.]
I S0 I N TERN ATI ON AL STAN DARD 2336- Fi rst edi ti on 996- 04- 01 ANSI I ntemat Hacksaw Part bl ades Parti e Set - 1: Di men si on s Lames Dot de sti es for h an d bl ades droi tes : Di mensi ons mktau x des l ames mai n Referen ce I S0 2336- n u mber 996(E) IS0 2336-1 :1 996(E) Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies) The work of preparing International Standards is normally carried out through IS0 technical committees Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization Draft International Standards adopted by the technical committees are circulated to the member bodies for voting Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote International Standard IS0 2336-l was prepared by Technical Committee lSO/-rC 29, Small too/s This first edition of IS0 2336-l as well as IS0 2336-2.1 996 cancels and replaces IS0 2336.1 980, which has been technically revised IS0 2336 consists of the following parts, under the general title Hacksaw blades - Part 7’ Dimensions for hand blades - Part Dimensions for machine blades IS0 996 All rights reserved Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher International Organization for Standardization Case Postale 56 l CH-1 21 Geneve 20 l Switzerland I NTERNATI ONAL STANDARD Hacksaw Part bl ades - for h an d bl ades b) Scope reference I S0 Thi s part h and h acksaw of I S0 2336 I t i s val i d for si ngl e the tooth mm, I,4 mm Di men si on s Di men si on s 25 mm Bl ade tres of that the pi n centrel i ne P, edged pi tch the di mensi on s i n fi gure an d the l ength, hol es centre of of of the bl ades of of wh i ch l ength to c) the bl ade are gi ven nu mber d) the wi dth , e) the th i ckn ess, f) the tooth , i s the di ameter the pi n di stance d It hol e teeth, N, between is be 25 mm, i n tabl e wi th of in cen- recommen ded l ocated on I S0 2336, a) “Saw shal l l ength, accordi ng be desi gnated to thi s 2336 (i e I , i n mi l l i metres; b, i n mi l l i metres; pi tch, P, by gi ven han d part of in mi l l i metres, the nu mber between h acksaw wi dth a = 2, tooth pi tch bl ade, mm, wh i ch of teeth, can be N, in mm, of parentheses of l ength of th i ckn ess P = mm i s desi gnated 2336- l = b = 0, 63 300 mm and of as fol l ows: - 300 x 2, x 0, 63 x or as fol l ows: Saw bl ade bl ade”; I S0 a, i n mi l l i metres; Saw bl ad e I S0 bl ades, of EXAMPLE A the bl ade h acksaw part than Desi g n ati on Han d thi s 1; of equal i s no greater to 2336-l su ppl emen ted sh own pi tch, speci fi es bl ades 300 tooth 2336- : 996( E) 1: Di men si on s I S0 I S0 ( 241 I S0 2336- l - 300 x x 0, 63 x I S0 2336- : 996(E) b NOTE - Th e sh ape of th e bl ade en ds i s l eft to th e man u factu rer’ s di screti on Fi gure Tabl e Di men si on s a +2 300 1) See cl au se Tooth b 63 spaci n g’) P N 008 32 24 I,4 18 i n mi l l i metres L d max HI 31 I S0 I CS 2336- : 996(E) 25 00 40 Descri ptors: Pri ce based metal worki ng on oages tool s, hand tool s, saws, h acksaws, bl ades, di men si on s, nu mber of teeth, desi gnati on