© ISO 2016 Cylindrical cutters with plain bore and key drive — Metric series Fraises cylindriques 1 taille, à surfacer, à alésage lisse, à entraînement par clavette — Série métrique INTERNATIONAL STAN[.]
INTERNATIONAL STANDARD ISO 2584 Second edition 2016-10-15 Cylindrical cutters with plain bore and key drive — Metric series Fraises cylindriques taille, surfacer, alésage lisse, entrnement par clavette — Série métrique Reference number ISO 2584:2016(E) © ISO 2016 ISO 2584:2016(E) COPYRIGHT PROTECTED DOCUMENT © ISO 2016, Published in Switzerland All rights reserved Unless otherwise specified, no part o f this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission Permission can be requested from either ISO at the address below or ISO’s member body in the country o f the requester ISO copyright o ffice Ch de Blandonnet • CP 401 CH-1214 Vernier, Geneva, Switzerland Tel +41 22 749 01 11 Fax +41 22 749 09 47 copyright@iso.org www.iso.org ii © ISO 2016 – All rights reserved ISO 2584:2016(E) Contents Page Foreword iv Scope Normative references Dimensions 3.1 Solid cutters 3.2 Interlocking cutters Annex A (informative) Relationship between designations in this International Standard and ISO 13399 (all parts) Bibliography © ISO 2016 – All rights reserved iii ISO 2584:2016(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies) The work o f preparing International Standards is normally carried out through ISO technical committees Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters o f electrotechnical standardization The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part In particular the different approval criteria needed for the di fferent types o f ISO documents should be noted This document was dra fted in accordance with the editorial rules of the ISO/IEC Directives, Part (see www.iso.org/directives) Attention is drawn to the possibility that some o f the elements o f this document may be the subject o f patent rights ISO shall not be held responsible for identi fying any or all such patent rights Details o f any patent rights identified during the development o f the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents) Any trade name used in this document is in formation given for the convenience o f users and does not constitute an endorsement For an explanation on the meaning o f ISO specific terms and expressions related to formity assessment, as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 2, Holding tools, adaptive items and interfaces This second edition cancels and replaces the first edition (ISO 2584:1972), o f which it constitutes a minor revision, notably with the addition o f Annex A, which gives the relationship between the designations of this International Standard and the ISO 13399 series iv © ISO 2016 – All rights reserved INTERNATIONAL STANDARD ISO 2584:2016(E) Cylindrical cutters with plain bore and key drive — Metric series Scope T h i s I nternationa l Standard s p e ci fie s the d i men s ion s o f me tric s erie s c yl i nd ric a l c utters with pla i n b ore and key d rive, i ntende d for fitti ng to c utter arb ors It is applicable to solid cutters and also to interlocking cutters Solid cutters are made either with straight teeth or with helicoidal teeth angled to the right or left; i nterlo cki ng c utters are a lways made with s traight or hel ico d i a l te e th a ngle d to the le ft and right a lternately The range of outside diameters of these cutters is taken from ISO 523 Normative references T he fol lowi ng i nd i s p en s able c u ments , i n whole or i n p ar t, are normatively re ference d i n th i s c u ment a nd are for its appl ic ation For date d re ference s , on ly the e d ition cite d appl ie s For u ndate d re ference s , the late s t e d ition o f the re ference d c u ment (i nclud i ng any amend ments) appl ie s ISO 240, Milling cutters — Interchangeability dimensions for cutter arbors or cutter mandrels Dimensions 3.1 Solid cutters Figure — Solid cutters Table D J s16 a 50 63 80 100 da H7 22 27 32 40 40 X 50 X 63 X X Dimensions in millimetres L 70 X 80 X X 100 X 125 X T he b o re a nd ke y way d i me n s io n s s h a l l b e i n acco rd a nce with the me tr ic s er ie s o f I S O © ISO 2016 – All rights reserved ISO 84: 01 6(E) Interlocking cutters Figure — I nterlocking cutters Table D Js16 80 10 125 a 16 da H7 32 40 50 60 80 X 100 X Dimensions in millimetres 125 X X L 160 200 X X X 250 X T he b o re a nd ke y way d i men s io n s s h a l l b e i n acco rd a nce wi th the me tr ic s e r ie s o f I S O © ISO 2016 – All rights reserved ISO 2584:2016(E) Annex A (informative) Relationship between designations in this International Standard and ISO 13399 (all parts) For relation sh ip b e twe en de s ignation s i n th i s I nternationa l Standard a nd pre ferre d s ymb ol s accord i ng to ISO 13399 (all parts), see Table A.1 Table A.1 — Relationship between designations in this International Standard and ISO 13399 (all parts) Symbol in ISO 2584 Reference in ISO 2584 D d Figures and Tables and Figures and Tables and d H7 Tables 1and L Figures and Tables and © ISO 2016 – All rights reserved Property name in ISO 13399 (all parts) cutting diameter connection diameter machine side tolerance class connection diameter machine side overall length Symbol in ISO 13399 (all parts) Reference in ISO 13399 (all parts) DC 71D084653E57F DCONMS 71EBDBF5060E6 TCDCONMS 72719B2BD8041 OAL 71D078EB7C086 ISO 2584:2016(E) Bibliography [1] [2] ISO 523,1) Milling cutters — Recommended range of outside diameters ISO 13399 (all parts), Cutting tool data representation and exchange 1) Withdrawn © ISO 2016 – All rights reserved ISO 84: 01 6(E) ICS 00.2 Price based on pages © ISO 2016 – All rights reserved