I nternational Standard @) 2262 0 % 4 4iYb I NTERNATIONAL ORGANIZATION FOR STANDARDIZATION~MEXPYl lAPOflHAR OP~AHl43AUHR flOCTAH~APTb43AUW4*ORGANlSATlON I NTERNATIONALE DE NORMALISATION General purpos[.]
I n t ern at i on al I N TE RN ATI ON AL ORG AN I ZATI ON Gen eral FOR St an d ard S TAN D ARD I ZATI ON ~ M E XPYl - l AP Of l H AR pu rpose t h i mbl es OP ~ AH l AU H R for 22 62 @) % 4i4 Yb f l OCTAH ~ AP Tb4 AU W4* ORG AN l SATl ON u se wi t h st eel I N TE RN ATI ON ALE wi re DE N ORM ALI S ATI ON ropes - Speci f i cat i on Co ss e s d ’ u sag es Se co n d U DC cou ran t s ed i t i on - d est i n kes r) Bt re u t i l i skes avec d es ca^ bl es en aci er - Sp&i f i cat i on s 4- 7- 667 72 : 62 66 Descri pt ors : l i fti n g e q u i pmen t , Ref wi re rope, rope t h i mbl es, speci fi cati on s, tests, perf orman ce N o I S0 2 - ( E) tests Pri ce bas e d on pag es Foreword I S0 ( the I n ternati onal nati onal stan d ard s St an d ard s is i n terested ri g ht to an d th e a I n ternati onal I S0 I ntern ati onal for a wi th ad opted l i nk bodi es I S0 was been 2262 ch n s, l i fti ng M arch 983 in approved th e thei r worl dwi d e h as t ake federati on devel opi n g commi t t ees I ntern ati onal al so a of E very been m e m be r org ani zati on s, part techn i cal in the as by the devel oped h ooks m e m be r are I nternati onal an d by Tech n i cal access ori es, bod i es of the Comm i t t ee an d fol l owi ng was ci rcu l ated to St an d ard s by Sou t h Bel g i u m J apan Swed en N orway Un i t ed m em be r bod y of Afri ca, Rep i n t ern at i on al Pri n t ed in Swi t z erl an d of Ki n g d om Pol an d th e fol l owi ng cou n t ry express ed di sapproval of th e d ocu m en t Neth erl an ds edi ti on the Rom an i a g rou n ds: s econ d 1 , to cou n tri es: I tal y F R I SO/TC ci rcu l ated I ndi a tech n i cal th e g overn men t al Au st ri a Can ad a Th i s bod y h as work com mi t t ees accept an ce of I n ternati onal au th ori zed Au stral i a Germ an y, Th e by before is work comm i t t ee I SO, approval Th e tech ni cal tech n i cal commi t t ee l i son St an d ards St an d ard steel m e m be r h as that bodi es) Cou n ci l Rou n d It on Stan dardi zati on ) I S0 wh i ch in bodi es for m em be r th rou g h for represen t ed m e m be r ( I S0 ou t su bj ect n on - g overn men t al , Draft th e carri ed in be Org an i z ati on bodi es can cel s Org an i zat i on an d for repl aces th e St an d ard i z at i on , fi rst edi ti on 984 ( i e I S0 2262- 972) on I N TERN ATI ON AL Gen eral I S0 STAN D ARD pu rpose t h i mbl es for u se wi t h steel wi re 2262- 984 ropes ( E) - Speci fi cat i on Scope an d fi el d of appl i cati on the fol l owi n g wi t h Th i s I n tern ati on al g en eral compl yi n g It 770 St an d ard pu rpose t h i mbl es wi th I S0 2408, M Pa( N /mm ) , d oes n ot to for h avi n g wi t h appl y speci fi es su i tabl e a for req u i remen t s wi t h st eel m ax i m u m d i amet ers t h i mbl es th e u se f rom u se wi th to 60 fi bre - ropes g rad e t h i mbl es an d sol i d t h i mbl es are not ten si l e - mm I S0 630, I S0 St ru ct u ral 461 , - prod u ct s - Hot di p 2408, St eel Ch aract eri sti cs wi re g al van i zed coati n g s on for Th i mbl es g en eral pu rposes 6892, mat eri al s - Ten si l e Th e n omi n al rope for si zes to of 60 j oi nt si ze wh i ch of it t h i mbl es a h as t h i mbl e been covered is the pri mari l y by th i s n omi n al d i amet er d esi g n ed I ntern ati on al Th e of th e ran g e g /m2 mi n sh al l in be or g al van i zed accord an ce f reed om formed , ed g es th e th e poi n t j oi nt m ay an d wi th from sh al l rou g h n ess, of m ay ei th er fi g u re oth er Prot ot ype St an d ard wi th I S0 a 461 d efects be wh i ch free f rom mi g h t an y d amag e th e be t h i mbl e al l owed sh al l after n ot be wel d ed g al van i zi n g 21 , type is at be th e poi n ted opti on speci fi cal l y ( see of the ordered fi g u re I) or wi th ou t man u fact u rer, by th e u n l ess pu rch aser of in t h i mbl es the sh al l co mpl y wi th the Obj ect prot otype test by th e th e is i n ten ded req u i remen t s th e to man u fact u rer of m ax i m u m d emon st rat e an d th i s h avi n g I n tern ati on al l oadi n g d i ti on s the t h i mbl e d i men s i on s that wh i ch St an d ard l i kel y to can be wi th - i mpos ed appropri at e it u n der n ormal di t i on s of u se tabl e Th e pu rpose met h od Materi al of of ou tsi de wh i ch compl i es th e wi th t h i mbl es I S0 630 are or to be eq u i val en t; f ormed it sh al l a steel sh al l I) At presen t at the st ag e of draft ( Revi si on of I S0 2408- 973 ) 2) At presen t at the st ag e of draft ( Revi si on of I S0 82- 974 ) be h ave th e th e th i s test man u fact u re speci fi cati on , f rom test i s f rom speci fi ed d i men si on s that n eatl y at at or mat eri al f ormed g ap ( see u pon Th e % t h i mbl es 20 an d be t h i mbl es stan d 20 of mm g i ven l east sh arp on e meet val u es ( N /mm2 ) ; si ze Di men si on s Th e MPa testi ng 2) Th e 520 fractu re: speci fi ed, at sh al l s mal l poi n ts N omi n al to rope Th e of defect, Th e ) Met al l i c accord an ce - A I S0 after ot h erwi se coati n g fl aw, Req u i remen t s ropes 360 Workman sh i p the I S0 in Gal van i zi n g coat i n g s ferrou s tested i n cl u ded st eel s Met al l i c fabri cated wh en ropes U n l ess Referen ces streng th : el on g ati on zi n c propert i es of Reevi n g mech an i cal 6892: for wi re ten si l e I S0 met h od n ormal protot ype test is of of to th e prove th i mbl e man u fact u re man u fact u ri n g in be th e d esi g n , An y or t ol eran ces u n d ert aken materi al ch an g e cri ti cal an d mat eri al d i men s i on s sh al l on in requ i re th e that mod i fi ed t h i mbl e I S0 2262- 984 Meth od ( E) of met h od t est If Two t est s desi g n , be fi tted 770 32 sh al l to of N OTE si l e in of x g rad e of x each si ze of man u fact u re 36 st ru cti on g rad e ( m i n i mu m an d be of steel axi al l y l oad ) of passed each t h i mbl e wi th sh al l breaki n g t h i mbl e, Th e core, of If to th e as protot ype rope on e l oad of n o mi n al st ru cti on be d i amet er After sh al l of rel ease d i men si on A d wi t h appl i ed si ze 4, steel the th e to d ( wh ere of of th e be tested t h i mbl es in accord an ce sh al i be wi th d e emed to h ave t h i mbl e fai l s tests or both fai l test, th e the re- test or t h i mbl es if sh al l mo re be th an on e d ee med to h ave fai l ed the test core, an d of mm 70 ( see MPa the t abl e) , ( N /mm ? a ten - Test certi fi cate u sed be ,5 sh al l test, prototype ori g i n al Th e Th e th e th e sh al l l oad ed the man u fact u re pas s 2408 t h i mbl es sh al l on of ten si l e MBL ou t met h od rope I S0 For carri ed an d ( N /m m2 the speci fi ed rope a MPa % be mat eri al of th ese test t h i mbl e th e t h i mbl e i s th e n omi n al l oad an y sh al l not th rou g h a d i amet er of perman en t exceed pi n wi th th e % of i ts g i vi n g or th e su ppl i er fol l owi n g sh al l , if requ i red , i n format i on provi de a cer- : rope) redu cti on man u factu rer ti fi cate a a) a referen ce b) n ame c) n omi n al d) a to th i s I n tern ati on al St an d ard; of ori g i n al an d ad d ress of man u fact u rer; val u e If an y fu rth er Pro ced u r e on e two f or t h i mbl e of t h i mbl es si ze of th i mbl e; re- t est i n g each of si ze th e tested s am e fai l s si ze, to pass desi g n , Tabl e the test, mat eri al - d ecl arat i on mat eri al a h ave an d Di men s i o n s of st eel an d passed ro pe that the met h od th e of t h i mbl es protot ype test N o m i n al ( N omi n al ) For si ze of rope t h i mbl e 1 d i amet er, d) m ax (1 d) C Gi n d) ( I 075 Ami n m ax ( 75 Dmi n d) ( d) of speci fi ed ( in ( 55 mi l l i met res K Gmi n d) d) mm ( d) 1 2 0, 5 27 3, 42 20 36 4 56 0, 25 45 5 7, O 3, 2, 21 54 6 5, 4, 21 ii.5 58 7, 1 6, l 24 35 63 7, 8, 7, 2 81 40 72 8 9, 81 4, 4, 63 65 1 ,5 20, 31 , 45 20 23, 21 5, 50 1 ,2 9 1 22 25 23 2, l 24 251 42, :z 08 26 9, 28, 45 65 1 4, 28 2 30, l 49 70 26 5, 9; 32 6, 34, SO 80 44 7, 2, 36 41 , 38, 3, 90 62 9, 5, 40 46 , 43, 70, o 00 80 22, 44 50 , 47, 77, 1 98 24, 0, 48 55 , 51 , 4, 20 21 26 3, 52 59 , 55 , 91 , 30 234 28, 6 56 64, 60 WJ 40 252 30, 9, 60 69 , 64 5, o 50 70 33, 42, i n t ermed i at e si zes of wi re ropes the n ext l arg er n o mi n al :i si ze of the t h i mbl e sh al l be u sed th e as t h i mbl es Di me n s i on s F are man u fact u re in s am e d esi g n , t h i mbl es cl au se wh i ch I S0 =- r F 2 - ( El IF- -1i Fi g u re - Th i mbl e wi th po i n t j - z- - - - F f - - Fi g u re N OTE - detai l ed Th e se d esi g n fi g u res of th e are on l y i n ten d ed to i l l u strate wh ere th e - Th i mbl e wi th o u t d i me n si o n s speci fi ed po i n t in th e tabl e are measu re d Th e y are n ot i n ten d ed to l i mi t th e th i mbl e