1. Trang chủ
  2. » Tất cả

ADE664290 1..9

9 1 0
Tài liệu đã được kiểm tra trùng lặp

Đang tải... (xem toàn văn)

THÔNG TIN TÀI LIỆU

Thông tin cơ bản

Định dạng
Số trang 9
Dung lượng 1,7 MB

Nội dung

ADE664290 1 9 Special Issue Article Advances in Mechanical Engineering 2016, Vol 8(8) 1–9 � The Author(s) 2016 DOI 10 1177/1687814016664290 aime sagepub com Dynamic modeling method for air bearings in[.]

Special Issue Article Dynamic modeling method for air bearings in ultra-precision positioning stages Advances in Mechanical Engineering 2016, Vol 8(8) 1–9 Ó The Author(s) 2016 DOI: 10.1177/1687814016664290 aime.sagepub.com Xiulan Bao1 and Jincheng Mao2 Abstract Air bearings have been widely used in ultra-precision positioning stages due to the property of nearly zero friction or wear Small vibration of the bearing reduces the overall moving and positioning precision of the stage and hampers its applications in fabrication facilities requiring nanometer moving and positioning precision In order to improve system precision, knowledge of the dynamic characteristics of air bearings is the first and crucial step However, it is still a challenge to set up an accurate dynamic model for air bearings due to the system complexity In this article, a novel method for the dynamic modeling of air bearing is proposed, which takes into account the dynamics in both the moving direction and the supporting direction An ultra-precision positioning dual stage is investigated using the proposed dynamic modeling method This stage has two sets of air bearings and can be used in integrated circuit fabrication equipments Moreover, dynamic behaviors of the ultra-precision positioning dual stage are studied and compared with experimental results to validate the effectiveness and accuracy of the proposed method Keywords Air bearing, dynamic model, ultra-precision, positioning stage, vibration Date received: 21 September 2015; accepted: July 2016 Academic Editor: Mark J Jackson Introduction The ultra-precision stage is a loading platform for precision positioning in multi-directions with high speed With the advancement of technology, ultra-precision positioning stages are increasingly used in various industries, such as lithography, computerized numerical control (CNC) machine tools, micro or nano topography measurement, and so on, to achieve positioning motion with high speed and high precision.1,2 The performance of ultra-precision positioning stages directly affects the quality and productivity of precision machine tools As the positioning stages on high precision are increasingly required, air bearings have been widely used in various ultra-precision positioning stages due to their merits of near zero friction or wear and less contamination.3 However, it has been recognized that there exists a phenomenon of air vortices, which will lead to small vibration with high-speed airflow.4 The small vibration of air bearing obviously reduces the overall moving and positioning precision of ultraprecision positioning stages5 and even causes a kind of self-excited instability to damage the whole positioning stages.6 In order to reduce the small vibration and improve the motion stability, the study of its dynamic characteristics is both necessary and urgent.7 College of Engineering, Huazhong Agricultural University, Wuhan, China School of Mechanical and Electrical Engineering, Wuhan Institute of Technology, Wuhan, China Corresponding author: Jincheng Mao, School of Mechanical and Electrical Engineering, Wuhan Institute of Technology, Wuhan, Hubei 430073, China Email: orchidbaoxl@mail.hzau.edu.cn Creative Commons CC-BY: This article is distributed under the terms of the Creative Commons Attribution 3.0 License (http://www.creativecommons.org/licenses/by/3.0/) which permits any use, reproduction and distribution of the work without further permission provided the original work is attributed as specified on the SAGE and Open Access pages (https://us.sagepub.com/en-us/nam/ open-access-at-sage) 2 In the past decades, performances of air bearings have been investigated theoretically and experimentally The general rules for dynamic parameters of the air bearing were analyzed, and dynamic design principles of air bearings were proposed to reduce the synchronization error of dual stages.8 Performances of air bearings and effects of the recess shape, orifice diameter, gas film thickness, and so on on the load capacity and mass flow rates were also investigated.9,10 The design method and preload technique for air bearings were proposed to improve the load capability and stiffness.11 The aforementioned works mainly focused on the effects of restrictor design parameters and operating conditions on the dynamic performance of air bearings Some scholars also studied the model and dynamic characteristics of the air bearings A fast modified three-dimensional (3D) flow mode from the Darcy equation and the modified Reynolds equation is deduced and used the finite element method to solve for the gas pressures distribution.12 The resistance network method (RNM) which takes into account the equilibrium of the mass flow rate and the squeeze film effect is developed, and dynamic behaviors such as variation in film gap and stability range of a grooved aerostatic bearing are also analyzed.13 They mainly studied the own dynamics of air bearing, without considering the impact of air bearing dynamic characteristics on supported motion stages And the established model of air bearing is too large to be used in dynamic model for supported motion stages Few studies dealt with the dynamic characteristics of supported motion stages with air bearings,14,15 but most of them modeled the bearing as a spring in the support direction This approach is simple enough to use in the overall modeling of supported motion stages, but the static and dynamic tilt characteristics of air bearings are ignored, which are also important for the realization of ultra-precision.16 Accurate dynamic modeling of the air bearing including the effects of dynamics in both directions and the dynamic characteristics of supported motion stages affected by air bearings are to be studied The rest of this article is organized as follows: in section ‘‘Description of the dual-stage system,’’ an ultra-precision positioning dual-stage system with two sets of air bearing is introduced In section ‘‘Dynamic modeling of the bearing system,’’ a dynamic modeling method for air bearings is proposed In section ‘‘Dynamic modeling of the stage,’’ using the proposed dynamic modeling method, a dynamic model with 24 degrees of freedom for the ultra-precision positioning dual stage is established In section ‘‘Experiments,’’ comparison with experimental results is made to validate the proposed dynamic modeling method Finally, conclusions are drawn in section ‘‘Conclusion.’’ Advances in Mechanical Engineering Figure Schematic diagram of the ultra-precision positioning dual-stage system Description of the dual-stage system Figure illustrates the ultra-precision positioning dualstage system, which contains two air bearing systems, one named the coarse air bearing system and another named air-foot Accordingly, the ultra-precision positioning dual-stage system can be divided into a coarse stage and a fine stage The coarse air bearing system is used for supporting the coarse stage, and the air-foot is used for supporting the fine stage In the ultra-precision positioning dual-stage system, the coarse stage is used for coarse and large range motion while the fine stage for precision and small range motion As for the coarse air bearing system, the coarse stage also has two linear motors to achieve movement in the x and y directions Each linear motor consists of a stator and a slider In the coarse stage, the slider of the x direction linear motor is also used as a stator of the y direction linear motor The specific structure of the coarse air bearing system is shown in Figure The linear motor stator of the x direction is fixed on the ground through bolts The linear motor slider of the x direction is suspended in the linear motor stator of the x direction by eight air bearings and can move in the x direction The actuator of the fine stage is a planar motor, the stator of which is linked with the linear motor slider of the y direction and suspended in the linear motor stator of the y direction by eight air bearings Hence, the fine stage can be driven in the x and y directions The coarse air bearing system is a combination of 16 air bearings which support the linear motor slider in the x and y directions In Figure 1, the 3D size of linear motor stator of the x direction is 585 mm 210 mm 65 mm, the 3D size of linear motor slider of the x direction is Bao and Mao Figure Structure of the coarse air bearing system flows out to the atmosphere by the vent finally The preloading device which is at the center of the air-foot generates suction by vacuum The advantage of vacuum preloading is that it creates a preloading force on the bearings without adding mass As for the coarse air bearing system, the fine stage mainly consists of a granite base, a planar motor, and a table The granite base is used to ensure the flatness of gas flow boundary The planar motor which is supported by the air-foot can drive the fine stage to move in the x and y directions and rotate around the z direction The workpiece requiring ultra-precision at high speed is placed on the table, which is mounted on the air-foot directly As mentioned above, the two air bearing systems are supporting the coarse stage and the fine stage, and they will influence the performance of the ultra-precision positioning dual-stage system directly Figure Schematic diagram of the air-foot 330 mm 280 mm 209 mm, and the length of the linear motor slider of the y direction is 900 mm The size of the granite base is 740 mm 566 mm 100 mm, the diameter of air-foot is 234 mm, the orifice diameter is 0.15 mm, the length of planar motor is 310 mm, and the 3D size of the table is 288 mm 319 mm 33 mm A schematic diagram of the air-foot is shown in Figure The air-foot has an annular air bearing, a circular vacuum preloading chamber, and two circular ambient pressure grooves which are used as vents The annular air bearings have 12 compound restrictors consisting of small orifices and rectangular chambers symmetrically Compressed gas flows through the feed holes to the chambers and then fills the air gap and Dynamic modeling of the bearing system The general form of the air bearing Figure 4(a) shows the general form of the air bearing, which is made of ceramic or hard aluminum alloy The air channels are processed, and the restrictor is installed inside the air bearing In the air bearing system, the precision granite or marble table is usually used as a support base The air bearings are placed on the support base and carry a motion stage to achieve movement of single direction or multi-directions The air bearing working surface are the support base and bottom surface of air bearing The air gap between the two surface is very small When an air bearing works, the lubricating gas flows through the restrictor c into the recess of the bearing and then fills the air gap before Advances in Mechanical Engineering Figure Modeling for an air bearing system Figure Structure schematic diagram of the air bearing flowing into the ambient As shown in Figure 4(b), the air supply pressure is p0 in the restrictor c, the air pressure becomes pd in the recess and then gradually decreases in the air film gap until being the ambient pressure pa This is the air film between two surfaces that supports the bearing and achieves lubrication Modeling method of the air bearing In order to investigate the effects of small vibration of air bearing on the motion stage, a dynamic modeling method for air bearings is presented in this section In practice, the motion stage is supported by an air bearing system composed by multiple air bearings As shown in Figure 5, a moving part is supported on a support base by an aerostatic bearing system The support base is denoted by body A, and the moving part denoted by body B Define So (O  XYZ) denoting the absolute frame, define SoA (OA  X A Y A Z A ), and SoB (OB  X B Y B Z B ) denoting local frames fixed on body A and body B, respectively In the conventional multi-rigid-body modeling, the two ends of spring are fixed on the two rigid bodies, respectively The acting positions of the spring on two rigid bodies are constant The direction of the spring stiffness changes with the relative pose of two rigid bodies In the air bearing, the gas film makes the supported stage move on the granite base with near zero friction When the supported stage has planar motion on the support base, support forces are always vertical upward, and the acting positions of the spring of the support base are varying The simplified spring in conventional multi-rigid-body modeling method is not applicable According to the characteristics of the air bearing, a signal air bearing can be simplified as a sliding spring which has the same direction with line OA Z A in body frame SoA , and location of the supported force is determined by the body B In other words, a signal air bearing can be modeled as a sliding spring whose direction is determined by the stator (body A), and applied position of spring force is determined by the slider (body B) In Figure 5, the moving body B accomplishes movement from the initial position to the final position A signal air bearing is simplified as a sliding spring h One end of the sliding spring h is fixed on the moving body B through point m The other end of the sliding spring h slides on the fixed body A through point n to ensure that the direction of the spring force is parallel with coordinate OA Z A of body frame SoA l is the effective deformation of the sliding spring h between the initial position and the final position Let o P1 and o P2 denote the position vectors of point m in the absolute coordinate So for the initial position and the final position 2, respectively Let uA and uB denote the deflection angles of the body frame SoA and body frame SoB , respectively, which are relative to the absolute frame So Then, the sliding spring deformation l can be expressed as follows l = ðo P2  o P1 Þ  sinðuB  uA Þ ð1Þ As mentioned above, a single air bearing can be modeled as a sliding spring which has only nonzero stiffness in the normal direction which represents the effect of the finite area of pressurized air The air bearing system can be modeled as a combination of distributed sliding springs, and each one of them represents a Bao and Mao Figure Dynamic model of the ultra-precision positioning dual stage single air bearing, which indicates three single air bearings in the air bearing system in Figure As shown in Figure 6, two air bearing systems in the ultra-precision positioning dual-stage system are modeled as two sets of multiple distributed sliding springs, which represent as blue spring in this figure In this way, the established air bearing model can reflect the tilt characteristics of actual air bearing system and can be used in the dynamic modeling of ultra-precision positioning dual stage Dynamic modeling of the stage In order to verify the proposed modeling method of air bearing, a dynamic model of the ultra-precision positioning dual stage is established, in which two air bearing systems are modeled using the method described in section ‘‘Dynamic modeling of the bearing system.’’ According to the proposed modeling method, an air bearing can be simplified as a sliding spring In the ultra-precision positioning dual stage, the 12 air bearings of the air-foot can be simplified as 12 distributed sliding springs mentioned above, to ensure the fine stage floats on the granite base with no horizontal friction and high vertical stiffness The 16 air bearings in the coarse air bearing system can also be simplified as 16 distributed sliding springs to support the linear motor slider in the x and y directions The influence of vibration caused by excitation of the air bearing system and mechanical structure dominates the performance of the ultra-precision positioning dual stage Because these effects are within the ultraprecision positioning dual stage, the stage needs to be divided into a finite number of components This number has to be relatively small so as to come up with a low dimensional description of the ultra-precision positioning dual stage On one hand, this number should be as small as possible in order to keep track of the basic mechanisms causing the dynamic behavior of the ultraprecision positioning dual stage; on the other hand, this number should be large enough to be able to describe all the relevant phenomena with sufficient details In order to be able to describe the aforementioned effects, the ultra-precision positioning dual stage is split up into four components or bodies Body contains the granite base and the linear motor stator of the x direction Body contains only the linear motor slider of the x direction or the linear motor stator of the y direction Body contains the linear motor slider of the y direction, the planar motor, and the table of the fine stage Body contains only the air-foot of the fine stage The dynamic model of the ultra-precision positioning dual stage is shown in Figure The blue springs represent air bearings, and the black springs fixed at both ends reflect the structural flexibility There are 24 generalized coordinates qi (i = 1,., 24) which are chosen to be equal to the global orientation of each body, that is, q(t) = ½q01 , q02 , q03 , q04 T , where q0i = ½xio , yio , zio , , bi , g i T (i = 1, 2, 3, 4); xio , yio , zio (i = 1, 2, 3, 4)—translation in the x, y, and z directions of body i; and , bi , g i (i = 1, 2, 3, 4)—rotation in the x, y, and z directions of body i Furthermore, the generalized velocities are chosen to be equal to the time derivatives of the generalized coordinates, that is, vi (t) = q_ i (t) (i = 1,., 24) The vibration differential equations are derived according to the Newton–Euler method The resulting equations are in the matrix form M v_ ðtÞ + CvðtÞ + KqðtÞ = F ð2Þ where M is the generalized mass matrix, C(q, t) is the damping matrix with only structural damping, K(q, t) is the stiffness matrix which has structural stiffness and air bearing stiffness, and F is the external excitation caused by air vortices In equation (2), M, C(q, t), and K(q, t) are 24 24 matrices Clearly, the stiffness matrix K(q, t) is not diagonal, which means the stiffness of air bearings is coupled with other structural stiffness The rigid body masses are calculated based on the shape and size of corresponding components The structural spring stiffness is obtained through the finite element analysis of the corresponding components in the fine stage In order to obtain the spring stiffness of air bearings, the following procedures are proposed: According to the structural properties of the coarse air bearing system and air-foot, we establish a 3D flow model of the air bearing, set proper boundary conditions and properties of the fluid, select the appropriate solver for iterative calculation, and use computational Advances in Mechanical Engineering fluid dynamics (CFD) software Fluent to obtain numerical solutions of the gas pressure distribution Obtain the load capability of each air bearing The load capability can be calculated by integrating the pressure in the lubricating film area The air bearing in the air-foot is a ring bearing, the load capacity of which can be calculated as follows R ð2 W = 2p P  rdr + Pa pR21  Pa pR22 ð3Þ R1 where P is the pressure in the lubricating film area, Pa is the atmospheric pressure, R1 is the inner diameter of the ring bearing, and R2 is the external diameter of the ring bearing The air bearing in the coarse air bearing system is a rectangular bearing, and its load capacity can be calculated as follows ð W= ðP  Pa ÞdA ð4Þ A where A is the regional area of the gas film Calculate the air bearing stiffness According to the above steps, the load capacity W can be calculated when the gas film thickness is h0 Then, the gas film thickness is increased by a small increment Dh, and the load capacity W is recalculated The stiffness of an air bearing can be obtained as follows kw = W0  W Dh ð5Þ There are three specifications of air bearings in the ultra-precision positioning dual stage: 12 air bearings in the air-foot, vertical air bearings, and the horizontal air bearings in the coarse air bearing system Each type of the spring has the same stiffness Through the above processes, the stiffness of a vertical air bearing and a horizontal air bearing in the coarse air bearing system can be identified as 75 and 66 N/mm, respectively The stiffness of an air bearing in the air-foot can be identified as 100 N/mm The damp effect of aerostatic bearing is squeezedfilm damping mainly, and its damping can be calculated by the following equation c= ∂W h_ ð6Þ The damping ratio of a vertical air bearing and a horizontal air bearing in the coarse air bearing system can be identified as 0.0097 and 0.0117, respectively The Figure Location of excitation points and measurement points damping ratio of an air bearing in the air-foot can be identified as 0.0074 The ultra-precision positioning dual stage modeled by four bodies is represented by a 24th-order dynamic model This dynamic model can be used for analysis in the simulation software package Simulink, by transforming it into C-code and using the so-called s-functions defined in Simulink Besides time-domain analysis, frequency-domain analysis can also be performed Experiments To confirm the validity of the simulation result, a series of experiments of the ultra-precision positioning dual stage are conducted The standard drop hammer tests on specimens have been carried out The locations of the excitation point and sensor arrangement are shown in Figure In the drop hammer test, the hammer equipped with a rubber head is used, and an acceleration sensor (CA-YD-106 and CA-YD-117) is placed at the test position to obtain the vibration responses The main technical specifications of CA-YD-106 were presented as follows: sensitivity at 20°C 5°C is 2.7 pC/m/s2, transverse sensitivity is 5%, maximum allowable acceleration is 1.96 104 m/s2, frequency range is 0.5–12 kHz, and the weight of the sensor is 15 g The main technical specifications of CA-YD-117 were presented as follows: sensitivity at 20°C 5°C is 50 pC/m/s2, transverse sensitivity is 5%, maximum allowable acceleration is 1.5 103 m/s2, frequency range is 0.2–3 kHz, and the weight of the sensor is 50 g Seven groups of experiments are performed, each group for four times, and average data values are taken The excitation point and measurement point for each experiment are shown in Table A modal hammer (ENDEVCO 2302-10, 500 lb range, frequency range of kHz, and sensitivity of 10 mV/lb) is used to supply an impulse force signal Using modal test and analysis Bao and Mao Table Locations of excitation points and sensors for each experiment Test number Excitation point Sensor location Sensor type Test Test Test Test Test Test Test Excitation point Excitation point Excitation point Excitation point Excitation point Excitation point Excitation point Measurement point Measurement point Measurement point Measurement point Measurement point Measurement point Measurement point CA-YD-106 CA-YD-106 CA-YD-117 CA-YD-117 CA-YD-117 CA-YD-117 CA-YD-106 Table Simulation and experimental modal of the ultra-precision positioning dual stage Simulation frequency (Hz) Experiment frequency (Hz) Modal shape Test number Error (%) 78 128 149 80 140 148 Rotation around y-axis Rotation around z-axis Rotation around y-axis 2.5 8.6 0.7 300 416 317 439 Rotation around x-axis Rotation around y-axis 490 591 724 754 494 589 739 809 Rotation around x-axis Rotation around z-axis Rotation around y-axis Rotation around x-axis 896 912 937 872 964 972 Translational motion along z-axis Rotation around x-axis Rotation around y-axis and x-axis 981 1003 Rotation around y-axis Test Test Test Test Test Test Test Test Test Test Test Test Test Test Test Test Test Test Test Test Test software LMS to collect excitation signals and response signals, with a sampling resolution of 0.5 Hz, the average frequency response functions are calculated from 20 sampling data The experimental results for tests 1–7 are shown in Figure In test and test 2, the excitation point is located on the stator of the y direction linear motor, and the measurement points are located on the stator and slider of the y direction linear motor, respectively The direction of excitation and measurement are in the z direction In test and test 4, the excitation point is located on the slider of the y direction linear motor; the measurement points are located on the stator and slider of the y direction linear motor, respectively; and the direction of excitation and measurement are the same as those in test and test The excitation and measurement points of the four tests are interchangeable; therefore, the common peak frequencies of the two frequency response functions in both tests are adopted According Figure Experimental results for tests 1–7 5.3 5.2 0.8 0.5 2.0 6.8 2.8 5.4 3.6 2.2 Advances in Mechanical Engineering Figure Simulation modes of the ultra-precision positioning dual stage on 78 Hz to the position and direction of the excitation points, the frequencies corresponding to the vibration mode for rotation around x-axis and y-axis and translational motion along z-axis of coarse stage are relatively easy to be represented in tests 1–4 The frequencies corresponding to the vibration mode for rotation around xaxis and z-axis of coarse stage are relatively easy to be excited in test The frequencies corresponding to the vibration mode for rotation around y-axis and z-axis of coarse stage are relatively easy to be excited in test The frequencies corresponding to the vibration mode for rotation around x-axis and y-axis of fine stage are relatively easy to be excited in test Comparison of simulation results and experimental results is shown in Table It can be seen from Table that the relative error ratio of the main peak frequencies is within 10%, and the simulation results of the dynamic model and experimental results are consistent The simulation modes of the ultra-precision positioning dual stage on 78 and 128 Hz are shown in Figures and 10, respectively Conclusion In this article, a novel dynamic modeling method for air bearing is proposed, which can simultaneously reveal the moving direction dynamics, and the tilt characteristics of bearings The proposed method models a signal air bearing as a sliding spring with force direction determined by stator and location by the slider and models a system of air bearings as a combination of distributed sliding springs And each spring has only nonzero stiffness along the normal axis which represents the effect of the finite area of pressurized air An ultra-precision positioning dual stage which contains multiple air bearings is presented, and the system structure and bearing distribution are also introduced The proposed dynamic modeling method has been applied successfully for an ultra-precision positioning dual stage which contains multiple air bearings An analytic dynamic model of an ultra-precision positioning dual stage with air bearings is established Model parameters of the dynamic model are obtained through the finite Figure 10 Simulation modes of the ultra-precision positioning dual stage on 128 Hz element analysis Experimental results demonstrate that the proposed modeling method for air bearings is accurate and effective The proposed dynamic model can quantitatively describe the ultra-precision positioning dual stage accurately and can be successfully used for controller design or dynamic optimization in the future Declaration of conflicting interests The author(s) declared no potential conflicts of interest with respect to the research, authorship, and/or publication of this article Funding The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This study was supported by the Scientific Research Funds of the Educational Commission of Hubei Province (grant no Q20151519), the Scientific Research Funds of the Transportation Commission of Hubei Province (grant no 201472122), and the Fundamental Research Funds for the Central Universities of China (grant no 2016PY017 and 2013QC007) References Wang FJ, Ma ZP, Gao WG, et al Dynamic modeling and control of a novel XY positioning stage for semiconductor packaging T I Meas Control 2015; 37: 177–189 Sen R, Pati C, Dutta S, et al Comparison between three tuning methods of PID control for high precision positioning stage J Metrol Soc India 2015; 30: 65–70 Otsu Y, Somaya K and Yoshimoto S High-speed stability of a rigid rotor supported by aerostatic journal bearings with compound restrictors Tribol Int 2011; 44: 9–17 Bao and Mao Dupint R Robust rotor dynamics for high-speed air bearing spindles Precis Eng 2015; 40: 7–13 Aoyama T, Koizumi K, Kakinuma Y, et al Numerical and experimental analysis of transient state microbounce of aerostatic guideways caused by small pores Ann CIRP 2009; 58: 367–370 Ye YX, Chen XD, Hu YT, et al Effects of recess shapes on pneumatic hammering in aerostatic bearings Proc IMechE, Part J: J Engineering Tribology 2010; 224: 231–237 Wardle FP, Bond C, Wilson C, et al Dynamic characteristics of a direct-direct drive air-bearing slide system with squeeze film damping Int J Adv Manuf Tech 2010; 47: 911–918 Ye YX, Chen XD and Luo X Dynamic design of aerostatic bearings in dual gas-lubricated stages China Mech Eng 2010; 21: 757–761 Chen XD and He XM The effect of the recess shape on performance analysis of the gas-lubricated bearing in optical lithography Tribol Int 2006; 39: 1336–1341 10 Chen XD, Chen H, Luo X, et al Air vortices and nanovibration of aerostatic bearings Tribol Lett 2011; 42: 79–183 11 Zhang CP and Liu Q Development of high-performance linear motor stage based on static-pressure air-bearing slider J Mech Sci Tech 2006; 25: 1212–1216 12 Tian Y Static study of the porous bearings by the simplified finite element analysis Wear 1998; 218: 203–209 13 Chen MF and Lin YT Static behavior and dynamic stability analysis of grooved rectangular aerostatic thrust bearings by modified resistance network method Tribol Int 2002; 35: 329–338 14 An CH, Zhang Y, Xu Q, et al Modeling of dynamic characteristic of the aerostatic bearing spindle in an ultraprecision fly cutting machine Int J Mach Tool Manu 2010; 50: 374–385 15 Chen XD, Bao XL, He XM, et al Vibration analysis of ultra-precision stage with air-bearing J Huazhong Univ Sci Tech 2007; 35: 5–8 16 Yoshimoto S, Tamura J and Nakamura T Dynamic tilt characteristics of aerostatic rectangular double-pad thrust bearings with compound restrictors Tribol Int 1999; 32: 731–738

Ngày đăng: 24/11/2022, 17:43

w