CAMERA SERVICE HINT (1)

Order No : SH-00898E-AA Issued on : 2017/4/3 Page : 1/4 IUO All NPM Models Equipped with Multi Recognition Camera CAUTION  This service information is designed for experienced repair technicians only and is not designed for use by the general public  It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product  Products powered by electricity should be serviced or repaired only by experienced professional technicians Any attempt to service or repair the product or products dealt with in this service information by anyone else could result in serious injury or death [ Subject ] [Multi recognition camera] Request for collecting information in case of recognition error [ Overview ] To identify the causes of the recognition errors with the multi recognition camera and to solve the problems promptly, log data are indispensable We ask for your cooperation in collecting such information [ Applicable camera types ] Applicable multi recognition cameras are as follows: Multi recognition camera V1 Type (N610157605AA) Type (N610157609AA) Type (N610157604AA) N610155092AB N610155092AB N610155122AB Machines concerned No Model No NM-EJM1E NM-EJM6D NM-EJM7D NM-EJR9A Model ID: Machine type NPM-TT2: Production modular NPM-D3: Production modular NPM-W2: Production modular NPM-VF: Odd-form component insertion machine Multi recognition camera V2 Type (MTKA005537AA) Type (MTKA005538AA) Type (MTKA002374AB) MTKA002377AC MTKA002377AC Machine concerned No Model No NM-EJM8D Model ID: Machine type NPM-DX: Modular mounter This document is protected by copyright laws Unauthorized copying and distribution is a violation of law MTKA002378AB P Page 2/4 [ Deescription ] m recognitionn camera, collecct the following three kinds of data, d and send them accompaanied by In case of trouubles with the multi the Q-Report, to the gg-mail address a for youur area Version information (Macchine system sooftware, Recog system softwaare, and Multi re ecog camera aapplication/firmw ware) Detailed reecognition imagges for one turnn Telnet log information [ Daata collection procedures ] Version infformation Find the versionn information off the following items on the M Machine-inform mation screens shown s below: (1) ( Machine sysstem software (2) ( Recog systtem software (3) ( Multi recog camera firmwaare (Fw_Ver) (4) ( Multi recog camera application (App_Verr) (5) ( Sensor lockk information (FW W/FPGA/LOCK K) ① ② ③ ④ ⑤ 2 Detailed reecognition imagges for one turnn (1) ( With the maachine stopped,, display the Reecog unit chk sccreen and presss the [Image Sa ave] button * Note To colle ect the image of tthe recognition errror with a particular p componnent, set ‘Error sttop count’ fo or that componennt to ‘1’ and take the steps sh hown left once thhe machine comees to a single stop due to an errror Unless the above settingg is made, the deetailed image of o component last st scanned for recognition will be savedd instead * Note If the machine is restarteed or another compon nent is scanned fo for recognition, all imag ges saved so far w will be lost P Page 3/4 (2) ( Select all noozzle position buttons b in order and click [Savee] to save the im mages for one turn t * Press the [O OK] button to diisplay the image of the selected nozzle for confirm mation (3) ( Specify the folder to save data d - For LNB: //lnbroot/maachineinformatioon/recog - For SD card: //PRIVATE/MEIG GROUP/PFSC//NPM/***(machhine serial No.)/RECOG 3 Telnet log information (1) ( Connecting to Telnet log (G Getting log from m machine to LN NB) (a) Open tthe Internet Expplorer on PC (such as the DGS S connected to the LNB) and speccify the followingg address: http://xxxx.xxx.xxx.xxx (IP address forr LNB):8080/LoogCollection (b) This oppens up the Tellnet log connecction tool dialog Set [Auuto Boot] to ”ON N” (c) Press the [Start] buttoon t Telnet log by starting the m machine Now you can collect the (2) ( Downloadinng Telnet log (Getting log from LNB) (a) Speciffy [StartTime] and a [Endtime], and a select the taarget time zonee to collect the Telnet T log (b) T log is to bbe collected Selectt the machine frrom which the Telnet Machinne name chang ged P Page 4/4 (c) Press the [Downloadd] button (d) d When [Compressed] appears, presss the [OK] buttoon and select thhe folder to be downloaded (e) d of the Telnet log This ccompletes the download [ Reemarks ] If you have anny questions, coontact the follow wing at PSFS: CS Departmennt, Electronic Device D Process BU Phone: +811-92-477-1205 Fax: +81-92-477-1664 Europe andd America: euu-usa_cs@gg.jp.panasonic.coom / East Asiaa: east_asia_cs@gg.jp.panaasonic.com Japan: jaapan_cs@gg.jp.panasonic.com m / South Assia: south_asia_ _cs@gg.jp.pannasonic.com ... Machine-inform mation screens shown s below: (1) ( Machine sysstem software (2) ( Recog systtem software (3) ( Multi recog camera firmwaare (Fw_Ver) (4) ( Multi recog camera application (App_Verr) (5) (... colleccted> Version information (Macchine system sooftware, Recog system softwaare, and Multi re ecog camera aapplication/firmw ware) Detailed reecognition imagges for one turnn Telnet log information...P Page 2/4 [ Deescription ] m recognitionn camera, collecct the following three kinds of data, d and send them accompaanied by In case of trouubles