sunx sensor
PHOTOELECTRIC SENSOR COMPACT PHOTOELECTRIC SENSOR Amplifier Built-in CX-400 Conforming to EMC Directive SERIES UL Recognition World Standard ‘Strong’, ‘High’ and ‘Less’ are keywords that everyone in the world understands We have a full lineup of world standard photoelectric sensors! ‘Strong’, ‘High’ and ‘Less’: three keywords that reflect the fundamental concepts in the design and operation of our sensors Strong: meaning being able to maintain fully reliable and stable levels of performance, no matter how adverse the work environment High: meaning technology-backed high detectability Less: meaning less waste, less time lost, less power consumption, less human and natural resources needed We bring you the ideal standard sensors for the 21st century dels! mo p 11 A long range and ine u Full l small spot! ⅷ Output ⅐⅐⅐ NPN, PNP ⅷ Connecting method ⅐⅐⅐ Cable type, M8 Plug-in connector type, M12 Pigtailed type ⅷ Cable length of cable type⅐⅐⅐ 0.5 m 1.640 ft, m 6.562 ft, m 16.404 ft 200 mm 7.874 in 100 mm 3.937 in Sensing range 70 to 200 mm 2.756 to 7.874 in The smallest spot in the industry at approx "2 mm "0.079 in Refer to p.9 l for ‘ORDER GUIDE’ Special transparent object circuit enhances detectability! A bright, spot at approx "5 mm "0.197 in Diffuse reflective • narrow-view type CX-423 A height difference equal to the thickness of one business card can be detected! A bright spot at approx "2 mm "0.079 in CX-441 Sensing range m 6.562 ft / 0.5 m 1.640 ft Retroreflective type for transparent object sensing Sensing range 300 mm 11.811 in / 100 mm 3.937 in / 50 mm 1.969 in Adjustable range reflective type CX-482/481 800 mm 31.496 in CX-442/444/443/441 100 mm 300 mm 3.937 in 11.811 in Sensing range 800 mm 31.496 in / 300 mm 11.811 in / 100 mm 3.937 in Diffuse reflective type CX-422/421/424 15 m 49.213 ft Sensing range m 16.404 ft / m 9.843 ft Retroreflective type CX-493/491 Sensing range 15 m 49.213 ft / 10 m 32.808 ft Thru-beam type CX-412/411 CX-400 Series Selection Long range sensing desired Ⅵ CX-400 series sensors solves all your sensing troubles Longest in its class with a distance of 15 m 49.213 ft CX-412 Rertroreflective type Longest in its class with a distance of m 16.404 ft CX-493 Diffuse reflective type Long sensing range 800 mm 31.496 in CX-422 Fit slit for thru-beam type Minimum size for sensing object "0.5 mm "0.020 in with slit fitted CX-411 Diffuse reflective • narrow-view type LED light source realizes a spot diameter of approx "2 mm "0.079 in CX-423 Adjustable range reflective type Approx "2 mm "0.079 in spot unaffected by background objects CX-441 High precision, 0.4 mm 0.016 in height difference sensing possible CX-441/443 Long sensing range 300 mm 11.811 in / 100 mm 3.937 in CX-442/444 Thru-beam type Sensing range 15 m 49.213 ft / 10 m 32.808 ft CX-411/412 Rertroreflective type Polarizing filter built-in CX-491 Adjustable range reflective type FGS function ensures stable sensing CX-44Ⅺ Thru-beam type Uses penetrating infrared light CX-412 Adjustable range reflective type Judgment based on incidence angle to avoid light-receiving amount swaying CX-44Ⅺ Thru-beam type Uses acrylic for lens surface for superior oil resistance CX-41Ⅺ Diffuse reflective type Uses acrylic for lens surface for superior oil resistance CX-42Ⅺ Rertroreflective type Uses acrylic for lens surface for superior oil resistance CX-49Ⅺ Diffuse reflective • narrow-view type The bright spot makes the beam axis clearly visible CX-423 Adjustable range reflective type Small parts sensing desired Thru-beam type The bright spot makes the beam axis clearly visible CX-44Ⅺ High precision type with built-in special transparent object circuit CX-481 Built-in special transparent object circuit Long sensing range m 6.562 ft CX-482 Minute height difference discernment desired (Background present) Adjustable range reflective type Glossy object sensing desired Area prone to dirt and dust Oil is scattered about Simple light beam axis adjustment desired Precise transparent object sensing desired Rertroreflective type ‘Strong’ against even the harshest conditions guarantees reliability Strongest in its class m Strong against oil and 2004 and based on coolant liquids m As of Aprilconducted by SUNX research CX-41Ⅺ/42Ⅺ/49Ⅺ The lens material for the thru-beam type, retroreflective type (excluding the CX-48Ⅺ) and the diffuse reflective type are made of a strong acrylic that resists the harmful effects of coolants These sensors can be used with confidence even around metal processing machinery that disperses oil mists The protection mechanism also conforms to IP67 (IEC) Strong against ethanol CX-44Ⅺ/48Ⅺ A strong, ethanol resistant polycarbonate was used for the front and display covers Safe even for installing near food processing machinery that disperses ethanol based detergents The protection mechanism also conforms to IP67 (IEC) Strong against noise Significantly stronger against inverter light and other extraneous light as well as high frequency and electromagnetic noise generated by high-pressure inverter motors and other devices Fluorescent light tube Inverter motor Oil Strong against interference Strong The interference prevention function lets two sensors to be mounted close together precisely Interference prevention filter (Optional) Thru-beam type Only CX-411 Strong Strong Noise Retroreflective type Automatic interference prevention function Diffuse reflective type Adjustable range reflective type Less energy Strong even in cold environments Power consumption Stable performance can be maintained even in environments of 52מЊC 31מЊF The ideal sensors that are people and environmentally friendly are born from the concept of ‘less’ waste Less space The sensors are compact in size at W11.2ן H31ןD20 mm W0.441ןH1.220ןD0.787 in The mounting pitch is also at the world standard size of 25.4 mm 1.000 in Compact size Less processing M8 plug-in connector type and M12 pigtailed type are available This contributes to less time spent in setting up In addition, cable types are available with cable lengths of 0.5 m 1.640 ft, m 6.562 ft and m 16.404 ft This results in less wastage Great maintainability 11.2 mm 0.441 in Industry standard mounting pitch 25.4 mm 1.000 in Cable type M8 plug-in connector type 20 mm 0.787 in 31 mm 1.220 in Digital laser sensor LS series m 6.562 ( m 16.404ftft/ ) m 6.562 ( m 16.404ftft/ ) Elbow Straight M12 pigtailed type CX-400 series No unnecessary cables or terminal blocks Straight 5m 16.404 ft 2m 6.562 ft m 6.562 ( m 16.404ftft/ ) 0.5 m 1.640 ft The new standard sensors for the 21st Century provide ‘high’ performance detection High precision optics and high performance special circuitry SUNX’s unique optical systems and specially designed electronic circuits provide stable sensing of even the minutest height difference and the thinnest transparent film Highest performance in its class m m As of April 2004 and based on research conducted by SUNX CX-441/443 Detecting a height difference of even as little as 0.4 mm 0.016 in possible (equivalent to one business card) 2.5 times the sensing capability! CX-481/482 A full range of m 6.562 ft sensing range types are available They are capable of sensing a 10 !m transparent film even at a long range CX-44Ⅺ ● Even different colored object can be sensed at roughly the same distance No adjuster control is needed when the setup is changed 30 % increase in sensing range between black and whitem compared to the conventional products! Twice the sensing range! m The difference in sensing range between black non-glossy paper (lightness: 5) and white nonglossy paper CX-482 ● BGS / FGS functions make even the most challenging settings possible Controls the adverse effects of background objects Precision High Refer to p.8 for details Easy to use high-level functions! CX-400 Conventional Conventional product product High High luminance Smallest spot in its class Spot Comparative ratio with representing conventional SUNX sensors Less resources used Wastage m 2004 and based on High luminance spot m As of Aprilconducted by SUNX research CX-423/44Ⅺ These sensors realize a high luminance red spot that provides bright visibility The sensing position can be checked at a glance Because it has the smallest spot in its class, approx "2 mm "0.079 in (CX-423/441), even the minutest object can be accurately detected CX-423 Great visibility approx "2 mm "0.079 in high luminance spot Less Less power consumed Less resources used The CX-400 series sensors achieve a maximum of approx 55 % the power consumption of conventional sensors Contributes to preserving the environment Based on environmental considerations, simplified packaging is used in order to reduce waste In addition, the bag is made from polyethylene which produces no toxic gases even when burned 45 A maximum % reduction compared to conventional sensors!! Thru-beam type Applications CX-411: 10 m 32.808 ft ● Detecting out of position tape feeder cassette CX-412: 15 m 49.213 ft The longest in its class m Slit mask m As of April 2004 and based on research conducted by SUNX Out of position m The longest in its class CX-411 Strong infrared beam CX-412 The longest in its class, it realizes a 15 m 49.213 ft long-distance sensing range Remarkable penetrating power enables applications such as package content detection (Note) Strong on dust and dirt CX-412 Because the light source is an infrared light, it is strong on dust and dirt compared to the red beam type ● Synchronizing sensor for image processing systems Even the thru-beam type is strong on mutual interference CX-411 Two CX-411 sensors, with their red beam light source, can be installed close together by fitting an interference prevention filter CX-411 Interference prevention filter (Optional) Note: When sensing utilizing penetrating power, make sure to verify using the actual sensor Retroreflective type The longest in its class CX-493: m 16.404 ft CX-491: m 9.843 ft The longest in its class m Long sensing range of m 16.404 ft CX-493 m A long m 16.404 ft sensing range is possible with the red LED type that is easy to align with the beam axis Can be used for wide automatic door shutters Retroreflective type with polarizing filters CX-491 Built-in polarizing filters ensure stable sensing even on a mirror surface object For transparent object sensing No.1 in the industry CX-482: m 6.562 ft CX-481: 0.5 m 1.640 ft m Strong against extraneous light and noise CX-491 With a level of performance ranked No.1 in the industry m, these sensors provide stable sensing Two sensors can be mounted close together m As of April 2004 and based on research conducted by SUNX The interference prevention function lets two sensors of any type to be mounted close together precisely Diffuse reflective type CX-422: 800 mm 31.496 in CX-421: 300 mm 11.811 in CX-424: 100 mm 3.937 in Applications ● Small parts sensing CX-423 CX-423: 70 to 200 mm Narrow-view type 2.756 to 7.874 in Smallest spot in its class m Beam axis alignment made easy with a high luminance spot beam CX-423 ● Passage confirmation on substrate conveyance equipment These sensors realize a high luminance red LED spot that provides bright visibility enabling the sensing position to be checked at a glance Because it has the smallest spot in its class, approx "2 mm "0.079 in, even the minutest object can be accurately detected Reduction of volume adjustment labor Because these sensors possess many variations depending on the sensing range, enables you to make optimal volume adjustment easily CX-423 CX-424 Great visibility approx "2 mm "0.079 in high luminance spot m As of April 2004 and based on research conducted by SUNX Introducing the transparent object sensing type sensor CX-48Ⅺ Our unique optical system and transparent object sensing circuitry provide stable sensing of even thinner transparent objects than the conventional models Applications ● Sensing glossy white electric appliances ● Sensing plastic bottles stacked on pallets Twice the sensing range! CX-491 Transparent objects detectable with CX-48Ⅺ (Typical examples) Sensing object Glass sheet Cylindrical glass Acrylic board Styrol (Floppy case) Food wrapping film Cigarette case film Vinyl sack Pet bottle (500m#) ● Passage confirmation of object on a conveyor belt CX-482 ● Detecting transparent film Sensing object size (mm in) t 7.0סt820.0ס Ⅺ50 Ⅺ1.969 "50 "1.969 # 969.1ס# 05סt 3.1סt150.0ס t 0.1סt930.0ס Ⅺ50 Ⅺ1.969 t 9.0סt530.0ס Ⅺ50 Ⅺ1.969 t! 01סm t 493.0סmil Ⅺ50 Ⅺ1.969 t! 02סm t 787.0סmil Ⅺ50 Ⅺ1.969 t! 03סm t 181.1סmil Ⅺ50 Ⅺ1.969 "66 "2.598 Reflector setting range CX-481: 300 to 500 mm 11.811 to 19.685 in, CX-482: to m 3.281 to 6.562 ft [with the RF-230 reflector at the optimum condition (Note)] Each object should pass across the beam at the center between the sensor and the reflector ?: Length of cylindrical glasses t : Thickness of sensing object Note: The optimum condition is defined as the condition in which the sensitivity level is set such that the stability indicator just lights up when the object is absent CX-481 CX-491 Adjustable range reflective type CX-442 CX-444 CX-441 CX-443 1.5 times longer than before 300 mm 11.811 in 100 mm 3.937 in 50 mm 1.969 in The longest in its class m Smallest spot in its class Spot diameter "2 mm "0.079 in approx High precision type Highest performance in its class m 50 mm 1.969 in Spot diameter "6.5 mm "0.256 in approx m CX-441/443 ● Can sense differences as small as 0.4 mm 0.016 in, with hysteresis of % or less ● Not affected by color The difference in sensing range between black and white is % or less (Note) An advanced optical system provides sensing performance that is approx 2.5 times than conventional models Even ultra-small differences of 0.4 mm 0.016 in can be detected accurately Both black and white objects can be sensed at the same distances No adjuster control is needed, even when products of different colors are moving along the production line Within the choice of 50 mm 1.969 in sensing range sensors, we offer small approx "2 mm "0.079 in spot type optimal for detecting minute object and large approx "6.5 mm "0.256 in spot type capable of sensing object covered with holes and grooves 30 % higher sensing capability 2.5 times the sensing capability! 0.4 mm 0.016 in ● Select from spot diameters as per the application Height differences of as little as 0.4 mm 0.016 in can be detected at a setting distance of 20 mm 0.787 in CX-443 CX-441 Note: The difference in sensing range between black non-glossy paper (lightness: 5) and white non-glossy paper Smallest spot in its class Spot diameter: "2 mm "0.079 in approx [Positioning] Detects minute holes Spot diameter: "6.5 mm "0.256 in approx Detection of presence / absence of objects Ignores minute holes and accurately detects objects [ ] m The bright spot makes beam axis alignment easy Can be used for sensing minute differences These sensors realize a high luminance red spot that provides bright visibility The sensing position can be checked at a glance Because the CX-441 sensor has the smallest spot in its class, approx "2 mm "0.079 in, even the minutest object can be accurately detected Equipped with a 5-turn adjuster so that even challenging range settings can be handled with ease Great visibility approx "2 mm "0.079 in high luminance spot CX-441 m As of April 2004 and based on research conducted by SUNX BGS / FGS functions make even the most challenging settings possible! For details on the operation of the BGS / FGS functions, refer to p.24, ‘PRECAUTIONS FOR PROPER USE’ The BGS function is best suited for the following case The FGS function is best suited for the following case BGS Background not present separated When object and background are FGS Background present When object and background are close together When the object is glossy or uneven Unaffected by gloss, color or uneven surfaces when sensing objects present on a conveyor belt Not affected if the background color changes or someone passes behind the conveyor BGS (Background suppression) function FGS (Foreground suppression) function The sensor judges that an object is present when light is received at position A of the light-receiving element (2-segment element) This is useful if the object and background are far apart The distance adjustment method is the same as the conventional adjustment method for adjustable range reflective type sensors The sensor judges that an object is present when no light is received at position B of the light-receiving element (2segment element) Accordingly, even objects that are glossy can be sensed This is useful if the object and background are close together, or if the object being sensed is glossy OFF Background ( Light received at element B, or light not received ) ON OFF in this condition only ( Light received ) at element A Object absent ON in all other conditions Object present For glossy object Element A Moving object in the back OFF A Element B Object ON Emitting element B Setting distance ON Lens Setting distance Conveyor Conveyor Light received at position B ( Conveyor Light received at position A Light is not received at position B, so a object is judged to be present A conveyor or other back-ground must be present ) Applications ● Small tablet sensing ● Biscuit sensing Detects minute objects unaffected by glossy background objects Uses FGS function CX-441 ● Passage confirmation Stable sensing even for thin objects Uses FGS function Not affected by color variations in objects and background objects Uses BGS function CX-443 CX-442 CX-400 ORDER GUIDE Retroreflective Appearance Model No NPN output 10 m 32.808 ft 15 m 49.213 ft m 9.843 ft (Note 1) Emitting element CX-411-P Red LED CX-412 CX-412-P Infrared LED CX-491 CX-491-P Red LED m 16.404 ft (Note 1) 50 to 500 mm 1.969 to 19.685 in (Note 1) CX-493 CX-493-P CX-481 CX-481-P Infrared LED Diffuse reflective Small spot Narrow-view CX-421-P CX-422 CX-422-P CX-423 CX-423-P CX-441-P CX-443 70 to 200 mm 2.756 to 7.874 in (Note 2) CX-424-P CX-441 800 mm 31.496 in (Note 2) CX-482-P CX-421 300 mm 11.811 in (Note 2) CX-482 CX-424 0.1 to m 0.328 to 6.562 in (Note 1) 100 mm 3.937 in (Note 2) Adjustable range reflective PNP output CX-411 Sensing range For transparent Long sensing With polarizing Long sensing object sensing range filters range Thru-beam Type CX-443-P Infrared LED Red LED to 50 mm 0.079 to 1.969 in Red LED CX-444 15 to 100 mm 0.591 to 3.937 in 20 to 300 mm 0.787 to 11.811 in CX-444-P CX-442 CX-442-P NOTE: Mounting bracket is not supplied with the sensor Please select from the range of optional sensor mounting brackets Notes: 1) The sensing range of the retroreflective type sensor is specified for the RF-230 reflector The sensing range represents the actual sensing range of the sensor The sensing ranges itemized in ‘A’ of the table below may vary depending on the shape of sensing object Be sure to check the operation with the actual sensing object Sensing range: A CX-491Ⅺ A Sensing object B Setting range of the reflector: B Sensor CX-493Ⅺ 3m 9.843 ft 5m 16.404 ft CX-481Ⅺ CX-482Ⅺ 50 to 500 mm 0.1 to m 1.969 to 19.685 in 0.328 to 6.562 ft 0.1 to m 0.1 to m 100 to 500 mm 0.8 to m 0.328 to 9.843 ft 0.328 to 16.404 ft 3.937 to 19.685 in 2.625 to 6.562 ft Reflector 2) The sensing range of the diffuse reflective type sensor is specified for white non-glossy paper (200 002ןmm 7.874 478.7ןin) as the object CX-400 SENSING CHARACTERISTICS (TYPICAL) 13.123 9.843 Reflector (RF-230) 6.562 L Sensor angular deviation Reflector (RF-230) $ 6.562 Sensor 3.281 3.281 100 100 200 3.937 3.937 7.874 Center Left Right Operating point ?(mm in) CX-481Ⅺ 20 20 Center Left Right $( ° ) Operating angle 600 23.622 # Sensor 200 7.874 100 3.937 40 Sensor angular deviation $L Sensor 20 20 Center Left Right Operating angle $( ° ) Retroreflective type Angular deviation 6.562 Reflector (RF-230) # 200 7.874 40 Sensing range L (mm in) # L Sensor 100 3.937 aןa mm White non-glossy paper 50 1.969 L L Sensor 100 100 200 3.937 3.937 7.874 Center Left Right Operating point ?(mm in) 3.281 40 Sensor angular deviation Sensor angular deviation $ Reflector L (RF-230) 20 20 Center Left Right $( ° ) Operating angle As the sensing object size becomes smaller than the standard size (white non-glossy paper 200 002ןmm 7.874 478.7ןin), the sensing range shortens, as shown in the left graph For plotting the left graph, the sensitivity has been set such that a 200 002ןmm 7.874 478.7ןin white non-glossy paper is just detectable at a distance of 100 mm 3.937 in ( ) Setting distance L (mm in) 200 7.874 200 7.874 Correlation between sensing object size and sensing range Sensing field 300 11.811 50 100 150 1.969 3.937 5.906 White non-glossy paper side length a (mm in) Diffuse reflective type 200 002ןmm 7.874 478.7ןin White nonglossy paper # L Sensor 100 3.937 400 15.748 Sensing range L (mm in) CX-421Ⅺ 400 15.748 10 10 20 0.394 0.394 0.787 Center Left Right Operating point ?(mm in) As the sensing object size becomes smaller than the standard size (white non-glossy paper 200 002ןmm 7.874 478.7ןin), the sensing range shortens, as shown in the left graph For plotting the left graph, the sensitivity has been set such that a 200 002ןmm 7.874 478.7ןin white non-glossy paper is just detectable at a distance of 300 mm 11.811 in 300 11.811 200 7.874 100 3.937 ( aןa mm White nonglossy paper L Sensor 40 1.575 17 20 20 40 0.787 0.787 1.575 Center Left Right Operating point ?(mm in) 50 100 150 1.969 3.937 5.906 White non-glossy paper side length a (mm in) 200 7.874 Reflector angular deviation Reflector angular deviation Reflector (RF-230) $ L Sensor Sensor Sensor 20 0.787 Reflector angular deviation Sensor angular deviation Reflector angular deviation Reflector (RF-230) $ L Sensor Sensor 20 20 40 Center Left Right $( ° ) Operating angle Correlation between sensing object size and sensing range 200 002ןmm 7.874 478.7ןin White non-glossy paper 50 1.969 40 Sensor 100 100 200 3.937 3.937 7.874 Center Left Right Operating point ?(mm in) 6.562 3.281 6.562 Sensor Sensor angular deviation Reflector (RF-230) $ L Diffuse reflective type Sensing field 100 3.937 Reflector angular Reflector deviation angular Reflector (RF-230) deviation 200 7.874 50 50 100 1.969 1.969 3.937 Center Left Right Operating point ?(mm in) CX-424Ⅺ Sensor 400 15.748 L 13.123 Parallel deviation Sensor angular deviation Reflector (RF-230) $ L 600 23.622 Reflector (RF-230) 400 15.748 200 7.874 40 CX-482Ⅺ 800 31.496 Setting distance L (mm in) Setting distance L (mm in) Sensor Angular deviation 800 31.496 Reflector (RF-230) # L 6.562 Retroreflective type Parallel deviation Setting distance L (mm in) 40 19.685 13.123 $L Sensor 200 7.874 26.247 19.685 Sensor angular deviation Reflector angular deviation Reflector (RF-230) L Angular deviation 26.247 Setting distance L (m ft) # Parallel deviation Reflector angular deviation Setting distance L (m ft) 9.843 Retroreflective type Setting distance L (m ft) Angular deviation 13.123 Setting distance L (m ft) Parallel deviation Setting distance L (m ft) CX-493Ⅺ Retroreflective type Setting distance L (m ft) CX-491Ⅺ ) 40 CX-400 SENSING CHARACTERISTICS (TYPICAL) CX-422Ⅺ Diffuse reflective type 200 002ןmm 7.874 478.7ןin White nonglossy paper # 500 19.685 L Sensor 800 31.496 ( aןa mm White nonglossy paper 400 15.748 L 20 20 40 0.787 0.787 1.575 Center Left Right Operating point ?(mm in) CX-423Ⅺ 50 100 150 1.969 3.937 5.906 White non-glossy paper side length a (mm in) Correlation between sensing object size and sensing range N6 100 200 002ןmm 3.937 7.874 478.7ןin Non-glossy paper # L Sensor 200 7.874 ( N6 100 3.937 aןa mm Non-glossy paper L ) Sensor 1 0.039 0.039 0.079 Center Left Right Operating point ?(mm in) 50 100 150 1.969 3.937 5.906 Non-glossy paper side length a (mm in) 200 7.874 Correlation between lightness and sensing range 200 7.874 Emitted beam The sensing region is represented by oblique lines in the left figure However, the sensitivity should be set with an enough margin because of slight variation in products 250 9.843 200 7.874 150 5.906 "5 mm "0.197 in N2 Dark N4 N6 Lightness N8 Light N1 N2 N3 N4 N5 N6 N7 N8 N9 ( Lightness shown on the left may differ slightly from the actual object condition ) "2.5 mm "0.098 in "2 mm "0.079 in "2.2 mm "0.087 in 50 1.969 Sensing region 100 3.937 110 4.331 100 3.937 "4 mm "0.157 in Visible spot range 0.079 Sensing range L (mm in) 200 7.874 As the sensing object size becomes smaller than the standard size (white non-glossy paper 200 002ןmm 7.874 478.7ןin), the sensing range shortens, as shown in the left graph For plotting the left graph, the sensitivity has been set such that a 200 002ןmm 7.874 478.7ןin white non-glossy paper is just detectable at a distance of 200 mm 7.874 in White White 200 7.874 Diffuse reflective type Sensing field Sensing range L (mm in) ) Sensor 40 1.575 Setting distance L (mm in) As the sensing object size becomes smaller than the standard size (white non-glossy paper 200 002ןmm 7.874 478.7ןin), the sensing range shortens, as shown in the left graph For plotting the left graph, the sensitivity has been set such that a 200 002ןmm 7.874 478.7ןin white non-glossy paper is just detectable at a distance of 800 mm 31.496 in Distance L (mm in) Setting distance L (mm in) 1,000 39.370 Sensing range L (mm in) Correlation between sensing object size and sensing range Sensing field 18 CX-400 SENSING CHARACTERISTICS (TYPICAL) CX-441Ⅺ Adjustable range reflective type 80 3.150 Black non-glossy paper Lightness: 50 05ןmm 1.969 969.1ןin Non-glossy paper # L 40 1.575 50 05ןmm 1.969 969.1ןin Non-glossy paper 20 0.787 L 60 2.362 50 1.969 40 1.575 30 1.181 20 0.787 Sensor 0.157 Black non-glossy paper Lightness: 25 0.984 Black Gray Blue Green Brown Red Orange 50 mm ⅐⅐⅐ 1.969 in 25 mm ⅐⅐⅐0.984 in Black rubber "6.2 mm 0.244 in "5.9 mm 0.232 in "5.3 mm 0.209 in 2 0.079 0.079 0.157 Center Left Right Operating point ?(mm in) These bars indicate the sensing range with the respective colors when the distance adjuster is set to a sensing range of 50 mm 1.969 in and 25 mm 0.984 in long, respectively, with white color The sensing range also varies depending on material Correlation between material (50 05mm 1.969 969.1in) and sensing range 50 1.969 25 0.984 50 mm ⅐⅐⅐ 1.969 in 25 mm ⅐⅐⅐0.984 in Black rubber 20 0.787 White nonglossy paper "6.5 mm 0.256 in Plywood 2 0.079 0.079 0.157 Center Left Right Operating point ?(mm in) # L Cardboard 60 2.362 50 1.969 White These bars indicate the sensing range with the respective objects when the distance adjuster is set to a sensing range of 50 mm 1.969 in and 25 mm 0.984 in long, respectively, with white non-glossy paper 80 3.150 Black non-glossy paper (Lightness: 5) Black non-glossy paper Lightness: Yellow Sensing range L (mm in) 19 50 05ןmm 1.969 969.1ןin Non-glossy paper Correlation between color (50 05mm 1.969 969.1in construction paper) and sensing range 25 mm ⅐⅐⅐0.984 in White nonglossy paper 80 3.150 40 1.575 White nonglossy paper 0.157 50 mm ⅐⅐⅐ 1.969 in Emitted beam Setting distance L (mm in) Setting distance L (mm in) # Sensor 10 0.394 25 0.984 • Setting distance: 50 mm 1.969 in 50 05ןmm 1.969 969.1ןin Non-glossy paper 20 0.787 50 1.969 Adjustable range reflective type Sensing fields • Setting distance: 25 mm 0.984 in L These bars indicate the sensing range with the respective colors when the distance adjuster is set to a sensing range of 50 mm 1.969 in and 25 mm 0.984 in long, respectively, with white color The sensing range also varies depending on material Correlation between material (50 05mm 1.969 969.1in) and sensing range Plywood Black Blue Gray Green Red Brown Orange White 25 mm ⅐⅐⅐0.984 in 30 1.181 "3 mm 0.118 in Cardboard 50 mm ⅐⅐⅐ 1.969 in Yellow Sensing range L (mm in) 25 0.984 40 1.575 "3 mm 0.118 in 2 0.079 0.079 0.157 Center Left Right Operating point ?(mm in) 50 1.969 CX-443Ⅺ "2 mm 0.079 in Black non-glossy paper (Lightness: 5) 0.157 2 0.079 0.079 0.157 Center Left Right Operating point ?(mm in) Correlation between color (50 05mm 1.969 969.1in construction paper) and sensing range "2 mm 0.079 in Sensor Sensor 0.157 # 60 2.362 50 1.969 40 1.575 30 1.181 20 0.787 White nonglossy paper 10 0.394 Black non-glossy paper Lightness: Sensing range L (mm in) 20 0.787 60 2.362 80 3.150 White nonglossy paper Distance L (mm in) 30 1.181 Setting distance L (mm in) Setting distance L (mm in) White nonglossy paper Sensing range L (mm in) 40 1.575 Emitted beam • Setting distance: 50 mm 1.969 in Distance L (mm in) Sensing fields • Setting distance: 25 mm 0.984 in These bars indicate the sensing range with the respective objects when the distance adjuster is set to a sensing range of 50 mm 1.969 in and 25 mm 0.984 in long, respectively, with white non-glossy paper CX-400 SENSING CHARACTERISTICS (TYPICAL) CX-444Ⅺ Adjustable range reflective type 40 1.575 80 3.150 # L "5.3 mm "0.209 in 5 10 0.197 0.197 0.394 Center Left Right Operating point ?(mm in) 100 3.937 ⅐⅐⅐ 100 mm 3.937 in 50 1.969 Cardboard ⅐⅐⅐ 50 mm 1.969 in These bars indicate the sensing range with the respective objects when the distance adjuster is set to a sensing range of 100 mm 3.937 in, 50 mm 1.969 in long, respectively, with white non-glossy paper Emitted beam 400 15.748 # L Sensor 5 10 0.197 0.197 0.394 Center Left Right Operating point ?(mm in) 100 3.937 Black non-glossy paper Lightness: 50 05ןmm 1.969 969.1ןin Non-glossy paper L ## Sensor 10 0.394 White nonglossy paper 300 11.811 300 11.811 50 05ןmm 1.969 969.1ןin Non-glossy paper 200 7.874 100 3.937 L ## Sensor 10 0.394 5 10 0.197 0.197 0.394 Center Left Right Operating point ?(mm in) Correlation between color (50 05mm 1.969 969.1in construction paper) and sensing range 400 15.748 Black non-glossy paper Lightness: 5 10 0.197 0.197 0.394 Center Left Right Operating point ?(mm in) Ⅺ15 mm Ⅺ0.591 in 200 7.874 Ⅺ11 mm Ⅺ0.433 in Distance L (mm in) 50 05ןmm 1.969 969.1ןin Non-glossy paper 200 7.874 • Setting distance: 300 mm 11.811 in Setting distance L (mm in) Black non-glossy paper Lightness: Setting distance L (mm in) Setting distance L (mm in) These bars indicate the sensing range with the respective colors when the distance adjuster is set to a sensing range of 100 mm 3.937 in, 50 mm 1.969 in long, respectively, with white color The sensing range also varies depending on material White nonglossy paper 100 3.937 100 3.937 1.181 30 Ⅺ9 mm Ⅺ0.354 in "8 mm "0.315 in Correlation between material (50 05mm 1.969 969.1in) and sensing range 400 15.748 400 15.748 300 11.811 Black Gray Blue Green Brown Red Orange White Yellow ⅐⅐⅐ 100 mm 3.937 in 200 7.874 300 mm ⅐⅐⅐ 11.811 in 200 mm ⅐⅐⅐ 7.874 in ⅐⅐⅐ 100 mm 3.937 in 100 3.937 Black rubber 200 mm ⅐⅐⅐ 7.874 in 100 3.937 These bars indicate the sensing range with the respective colors when the distance adjuster is set to a sensing range of 300 mm 11.811 in, 200 mm 7.874 in and 100 mm 3.937 in long, respectively, with white color The sensing range also varies depending on material Plywood 300 mm ⅐⅐⅐ 11.811 in Cardboard 200 7.874 Black non-glossy paper (Lightness: 5) 300 11.811 White nonglossy paper Sensing range L (mm in) "6.5 mm "0.256 in Correlation between material (50 05mm 1.969 969.1in) and sensing range • Setting distance: 200 mm 7.874 in White nonglossy paper 50 1.969 Adjustable range reflective type Sensing fields • Setting distance: 100 mm 3.937 in 10 0.394 10 0.394 Black non-glossy paper (Lightness: 5) Black Blue Gray Green Red Brown Orange White ⅐⅐⅐ 50 mm 1.969 in Yellow Sensing range L (mm in) ⅐⅐⅐ 100 mm 3.937 in 50 1.969 Sensor 5 10 0.197 0.197 0.394 Center Left Right Operating point ?(mm in) 100 3.937 50 1.969 # L White nonglossy paper 10 0.394 5 10 0.197 0.197 0.394 Center Left Right Operating point ?(mm in) CX-442Ⅺ 50 1.969 "8 mm "0.315 in 20 0.787 50 05ןmm 1.969 969.1ןin Non-glossy paper Sensor Correlation between color (50 05mm 1.969 969.1in construction paper) and sensing range Black non-glossy paper Lightness: Distance L (mm in) 20 0.787 Sensor 10 0.394 50 05ןmm 1.969 969.1ןin Non-glossy paper Black non-glossy paper Lightness: "9 mm "0.354 in 80 3.150 Black rubber # L 40 1.575 100 3.937 100 3.937 Sensing range L (mm in) 10 0.394 60 2.362 Plywood 50 05ןmm 1.969 969.1ןin Non-glossy paper Black non-glossy paper Lightness: Emitted beam White nonglossy paper White nonglossy paper Sensing range L (mm in) 20 0.787 • Setting distance: 100 mm 3.937 in Setting distance L (mm in) White nonglossy paper 30 1.181 Setting distance L (mm in) • Setting distance: 50 mm 1.969 in Setting distance L (mm in) Sensing fields • Setting distance: 25 mm 0.984 in These bars indicate the sensing range with the respective objects when the distance adjuster is set to a sensing range of 300 mm 11.811 in, 200 mm 7.874 in and 100 mm 3.937 in long, respectively, with white nonglossy paper 20 CX-400 PRECAUTIONS FOR PROPER USE All models This product is not a safety sensor Its use is not intended or designed to protect life and prevent body injury or property damage from dangerous parts of machinery It is a normal object detection sensor Mounting • The tightening torque should be 0.5 N⅐m or less M3 (length 12 mm 0.472 in) screw with washers Sensor mounting bracket (Optional) Wiring • Make sure that the power supply is off while wiring • Take care that wrong wiring will damage the sensor • Verify that the supply voltage variation is within the rating • If power is supplied from a commercial switching regulator, ensure that the frame ground (F.G.) terminal of the power supply is connected to an actual ground • In case noise generating equipment (switching regulator, inverter motor, etc.) is used in the vicinity of this product, connect the frame ground (F.G.) terminal of the equipment to an actual ground • Do not run the wires together with high-voltage lines or power lines or put them in the same raceway This can cause malfunction due to induction • Extension up to total 100 m 328.084 ft (thru-beam type: both emitter and receiver) is possible with 0.3 mm2, or more, cable However, in order to reduce noise, make the wiring as short as possible • Make sure that stress by forcible bend or pulling is not applied directly to the sensor cable joint Others • Do not use during the initial transient time (50 ms) after the power supply is switched on • Take care that the sensor is not directly exposed to fluorescent light from a rapid-starter lamp or a high frequency lighting device, as it may affect the sensing performance • This sensor is suitable for indoor use only • Do not use this sensor in places having excessive vapor, dust, etc., or where it may come in direct contact with water or corrosive gas • Take care that the sensor does not come in direct contact with water, oil, grease or organic solvents, such as, thinner, etc • This sensor cannot be used in an environment containing inflammable or explosive gases • Never disassemble or modify the sensor CX-41Ⅺ/42Ⅺ CX-49Ⅺ/48Ⅺ Functional description Stability indicator (Green) (Note 1) Lights up under the stable light condition or the stable dark condition ( Operation indicator (Orange) (Note 2) Lights up when the output is ON ( ) ( ) Sensing object MAX MIN Sensitivity adjuster (Note 1) Sensing range becomes longer when turned clockwise ) Similarly, adjust for up, down, left and right angular movement of the emitter Further, perform the angular adjustment for the receiver also Check that the stability indicator (green) lights up Choose the operation mode, Light-ON or Dark-ON, as per your requirement, with the operation mode switch Operation mode switch (Note 1) L : Light-ON D : Dark-ON ( ) Emitter Notes: 1) Not incorporated on the thru-beam type sensor emitter 2) It is the power indicator (Green LED)(lights up when the power is ON) for the thru-beam type sensor emitter Operation mode switch Operation mode switch Receiver Retroreflective type sensor Description Light-ON mode is obtained when the operation mode switch (located on the receiver for the thru-beam type) is turned fully clockwise (L side) Dark-ON mode is obtained when the operation mode switch (located on the receiver for the thru-beam type) is turned fully counterclockwise (D side) Beam alignment Set the operation mode switch to the Light-ON mode position (L side) Placing the sensor and the reflector face to face along a straight line, move the reflector in the up, down, left and right directions, in order to determine the range of the light received condition with the help of the operation indicator (orange).Then, set the reflector at the center of this range Similarly, adjust for up, down, left and right angular movement of the reflector Further, perform the angular adjustment for the sensor also Check that the stability indicator (green) lights up Choose the operation mode, Light-ON or Dark-ON, as per your requirement, with the operation mode switch Sensing object Thru-beam type sensor Set the operation mode switch to the Light-ON mode position (L side) Placing the emitter and the receiver face to face along a straight line, move the emitter in the up, down, left and right directions, in order to determine the range of the light received condition with the help of the operation indicator (orange) Then, set the emitter at the center of this range 21 Reflector Sensor CX-400 PRECAUTIONS FOR PROPER USE CX-41Ⅺ/42Ⅺ CX-49Ⅺ/48Ⅺ Retroreflective type sensor (except CX-491Ⅺ) Sensitivity adjustment Step Description MAX Turn the sensitivity adjuster fully counterclockwise to the minimum sensitivity position, MIN MAX MIN Sensitivity adjuster In the light received condition, turn the sensitivity adjuster slowly clockwise and confirm the point A where the sensor enters the ‘Light’ state operation A MIN A In the dark condition, turn the sensitivity adjuster further clockwise until the sensor enters the ‘Light’ state operation and then bring it back to confirm point B where the sensor just returns to the ‘Dark’ state operation If the sensor does not enter the ‘Light’ state operation even when the sensitivity adjuster is turned fully clockwise, the position is point B B MAX MIN • Please take care of the following points when detecting materials having a gloss ( ) The position at the middle of point A and B is the optimum sensing position MAX MIN Note: Use the ‘minus’ adjusting screwdriver (please arrange separately) to turn the adjuster slowly Turning with excessive strength will cause damage to the adjuster Diffuse reflective type Retroreflective type Thru-beam type Light received condition Receiver Dark condition Sensor Reflector Glossy surface Retroreflective type sensor with polarizing filters (CX-491Ⅺ) • If a shiny object is covered or wrapped with a transparent film, such as those described below, the retroreflective type sensor with polarizing filters may not be able to detect it In that case, follow the steps given below Emitter Reflector Receiver Sensor • Can wrapped by clear film • Aluminum sheet covered by plastic film • Gold or silver color (specular) label or wrapping paper Steps • Tilt the sensor with respect to the sensing object while fitting • Reduce the sensitivity • Increase the distance between the sensor and the sensing object • Optimum sensing is possible when the position of the transparent sensing object is set at the center of the sensor and the reflector If the sensing position is set near the sensor or the reflector, the sensing may be unstable In this case, set the sensing position at the center of the sensor and the reflector Reflector Sensing object Sensor Sensor Reflector Transparent sensing object • When the sensor detects an uneven plastic receptacle or glass bottle, the received-light amount may differ with the sensing position or direction Adjust the sensitivity after confirming the stable sensing condition by turning the sensing object, etc • When sensing pipe-shaped transparent sensing object, set it in a standing, not lying, position as shown in Figure A The sensor may fail to detect a lying object as shown in Figure B Sensor Sensing object Relation between output and indicators In case of Light-ON Stability Operation Output indicator indicator Sensing condition In case of Dark-ON Output Stable light receiving ⅷ ON OFF ON Stable dark receiving B Operation Stability indicator indicator ⅷ Reflector ⅷ Unstable dark receiving ⅷ A ⅷ OFF Unstable light receiving ⅷ ⅷ 10Њ to 30Њ Retroreflective type sensor for transparent object sensing (CX-48Ⅺ) Sensing object ⅷ Sensing object Example of sensing objects Optimum position A B Emitter Make L, shown in the diagram, sufficiently long Install at an angle of 10 to 30 degrees to the sensing object L Make L sufficiently long Sensor Reflector Sensor ⅷ ⅷ ⅷ, ⅷ : lights up ⅷ : lights off 22 CX-400 PRECAUTIONS FOR PROPER USE CX-41Ⅺ Slit mask (Optional) • With the slit mask (OS-CX-Ⅺ), the sensor can detect a small object However, the sensing range is reduced when the slit mask is mounted How to mount Insert the fixing hook into the fixing groove Then, pressing the slit mask against the main unit, insert the fixing tab into the fixing groove Fixing groove Fixing tab Interference prevention filter (Optional) (Exclusively for CX-411Ⅺ) • By mounting interference prevention filters (PF-CX4-Ⅺ), two sets of CX-411Ⅺ can be mounted close together However, the sensing range is reduced when the interference prevention filter is mounted • The filters can be mounted by the same method as for the slit masks • The two sets of sensors should be fitted with different types of interference prevention filters Interference prevention does not work if the filters are mounted for emitters only, receivers only or if the same model No of interference prevention filters are mounted on both sets of sensors Removing tab Fitted with PF-CX4-H Fixing groove Slit mask Fixing hook How to remove Fitted with PF-CX4-V Insert a screwdriver into the removing tab Pull forward while lifting the removing tab CX-44Ⅺ Mounting Operation mode switch • Care must be taken regarding the sensor mounting direction with respect to the object’s direction of movement Sensing object Sensing object Do not make the sensor detect an object in this direction because it may cause unstable operation Sensing object • When detecting a specular object (aluminum or copper foil, etc.) or an object having a glossy surface or coating, please take care that there are cases when the object may not be detected due to a change in angle, wrinkles on the object surface, etc • When a specular body is present below the sensor, use the sensor by tilting it slightly upwards to avoid wrong operation Operation mode switch Description L D Detection-ON mode is obtained when the operation mode switch is turned fully clockwise (L side) L D Detection-OFF mode is obtained when the operation mode switch is turned fully counterclockwise (D side) Note: Use the ‘minus’ screwdriver (please arrange separately) to turn the adjuster slowly Turning with excessive strength will cause damage to the adjuster • Depending on whether you select the BGS or FGS function, the output operation changes as follows Specular face Sensing range Setting distance Non-detectable area Tilt • If a specular body is present in the background, wrong operation may be caused due to a small change in the angle of the background body In that case, install the sensor at an inclination and confirm the operation with the actual sensing object • Take care that there is a non-detectable area right in front of the sensor L-ON ON OFF D-ON ON OFF L-ON ON OFF D-ON ON OFF BGS FGS 23 CX-400 PRECAUTIONS FOR PROPER USE CX-44Ⅺ Stability indicator BGS function • Since the CX-44Ⅺ uses a 2-segment photodiode as its receiving element, and sensing is done based on the difference in the incident beam angle of the reflected beam from the sensing object, the output and the operation indicator (orange) operate according to the object distance Furthermore, the stability indicator (green) shows the margin of the setting distance Sensor Description Distance adjuster Turn the distance adjuster fully counterclockwise to the minimum sensing range position (CX-441Ⅺ/443Ⅺ/ 444Ⅺ: 20 mm 0.787 in approx., CX-442Ⅺ: 40 mm 1.575 in approx.) Turn fully Setting distance Place an object at the required distance from the sensor, turn the distance adjuster gradually Sensing object clockwise, and find out point A where the sensor ON (Lights up) Output (Operation indicator) (BGS mode⅐Detection-ON) changes to the detecting condition OFF (Lights off) Stable operating Stable operating condition condition Unstable operating condition Stability indicator Step Lights up Lights off BGS / FGS functions • This sensor incorporates BGS / FGS functions Select either BGS or FGS function depending on the positions of the background and sensing object Remove the object, turn the adjuster clockwise further until the sensor goes into the detecting state again Once it has entered, turn the distance adjuster backward until the sensor returns to the non-detecting condition This position is designated as point B When the sensor does not go into the detecting condition even if the adjuster is turned fully clockwise, the position where the adjuster was fully turned is regarded as the point B There may be more than turn between point A and B, since this sensor incorporates a 5-turn adjuster BGS function Sensing object Background • This function is used when the sensing object is apart from the background Optimum position The optimum position to stably detect objects is the center point between A and B FGS function Step FGS function • This function is used when the sensing object contacts the background or the sensing object is glossy, etc Description Distance adjuster Turn the distance adjuster fully clockwise to the maximum sensing range position (CX-441Ⅺ/443Ⅺ: 50 mm 1.969 in approx., CX-444Ⅺ: 100 mm 3.937 in approx., CX-442Ⅺ: 300 mm 11.811 in approx.) Sensing object Background Distance adjustment • When this product is used, be sure to carry out the distance adjustment • Since the distance adjuster of this sensor is a 5-turn adjuster, when the point A and B is adjusted as explained in the table right, there may be more than turn between the point A and B Therefore, make sure to remember the turns of both points to find the optimum position • Be sure to wire the sensing mode selection input (Pink / 2) before distance adjustment If the wiring is done after the distance adjustment, the sensing area is changed • Turn the distance adjuster gradually and lightly with a ‘minus’ screwdriver (please arrange separately) In order to protect itself, the distance adjuster idles if turned fully If the adjuster is idled when distance adjustment is done, carry out the adjustment again Turn fully In the state where the sensor detects the background, turn the distance adjuster gradually counterclockwise, and find out point A where the sensor changes to the non-detecting condition Place an object at the required distance from the sensor, turn the adjuster counterclockwise further until the sensor goes into the non-detecting condition again Once entered, turn the distance adjuster backward until the sensor returns to the detecting condition This position is designated as point B When the sensor does not go into the nondetecting condition even if the adjuster is turned fully counterclockwise, the position where the adjuster was fully turned is regarded as the point B There may be more than turn between point A and B, since this sensor incorporates a 5-turn adjuster The optimum position to stably detect objects is Optimum position the center point between A and B Others • Its distance adjuster is mechanically operated Do not drop; avoid other shocks 24 CX-400 DIMENSIONS (Unit: mm in) CX-41Ⅺ The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/ CX-41Ⅺ-Z Sensor Sensitivity adjuster (Note 1) 11.9 0.469 Sensitivity adjuster (Note 1) 11.9 0.469 Operation indicator (Orange)(Note 2) Sensor Operation indicator (Orange)(Note 2) 7.85 0.309 3.95 0.156 7.85 0.309 3.95 0.156 Stability indicator (Green)(Note 1) Stability indicator (Green)(Note 1) 11.2 0.441 Beam axis Operation mode switch (Note 1) 20 0.787 0.118 15.5 0.610 25.4 31 1.220 1.000 11.2 0.441 ( Beam axis 15.5 31 0.610 25.4 1.220 1.000 35.5 1.398 42.5 1.673 2.5 0.098 2-M3020.0 5.0ן thru-hole threads ) "3.7 "0.146 cable, m 6.562 ft long Sensitivity adjuster (Note 1) Center of sensing 0.157 ( ) M12 connector 44 (1.732 ) 2-M3020.0 5.0ן thru-hole threads Operation mode switch 20 0.787 0.118 11.2 0.441 Beam-receiving part 2.5 0.098 7.85 0.309 3.95 0.156 Stability indicator (Green) Operation mode switch (Note 1) 15.5 0.610 31 25.4 1.220 1.000 11.9 0.469 Operation indicator (Orange) 7.85 0.309 3.95 0.156 20 0.787 0.118 Beam axis M8 connector Sensitivity adjuster 11.9 0.469 Stability indicator (Green)(Note 1) 11.2 0.441 2-M3020.0 5.0ן thru-hole threads "9.4 "0.370 CX-49Ⅺ CX-48Ⅺ Sensor CX-42Ⅺ Sensor Operation indicator (Orange)(Note 2) 2.5 ( 0.098 ) Notes: 1) Not incorporated on the emitter 2) It is the power indicator (green) on the emitter Notes: 1) Not incorporated on the emitter 2) It is the power indicator (green) on the emitter CX-41Ⅺ-J Operation mode switch (Note 1) 20 0.787 0.118 15.5 0.610 25.4 31 1.220 1.000 0.157 Beam-emitting part 2.5 (0.098) 2-M3020.0 5.0ן thru-hole threads "3.7 "0.146 cable, m 6.562 ft long "3.7 "0.146 cable 300 (11.811) Notes: 1) Not incorporated on the emitter 2) It is the power indicator (green) on the emitter CX-49Ⅺ-Z CX-48Ⅺ-Z Sensor CX-42Ⅺ-Z Sensitivity adjuster Operation indicator (Orange) CX-49Ⅺ-J CX-48Ⅺ-J Sensor CX-42Ⅺ-J 11.9 0.469 Sensitivity adjuster 7.85 0.309 3.95 0.156 4 0.157 0.157 Beam-emitting part "9.4 "0.370 Stability indicator (Green) 20 0.787 0.118 15.5 0.610 25.4 35.5 31 42.5 1.398 1.220 1.000 1.673 2-M3020.0 5.0ן thru-hole threads 11.9 0.469 7.85 0.309 3.95 0.156 Operation mode switch Stability indicator (Green) 11.2 Beam-receiving 0.441 part Center of sensing Operation indicator (Orange) 11.2 Beam-receiving 0.441 part 0.157 ( 2.5 0.098 M8 connector 0.157 Beam-emitting part Operation mode switch Center of sensing 15.5 0.610 31 25.4 1.220 1.000 ) 20 0.787 0.118 2.5 ( 0.098 ) M12 connector 44 (1.732 ) 2-M3020.0 5.0ן thru-hole threads "3.7 "0.146 cable 300 (11.811) 25 CX-400 DIMENSIONS (Unit: mm in) CX-44Ⅺ The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/ CX-44Ⅺ-Z Sensor 12.5 0.492 Operation indicator (Orange) 8.2 0.323 0.157 Operation mode switch Distance adjuster (5-turn) 11.2 0.441 Distance adjuster (5-turn) 22 0.866 Beamemitting part Center of sensing 11.2 0.441 0.9 0.035 31 25.4 1.220 1.000 22 0.866 Center of sensing 2-M3020.0 5.0ן thru-hole threads RF-230 "3.7 "0.146 cable, m 6.562 ft long ( 2.8 0.079 0.110 Beamreceiving part 20 0.787 0.118 0.9 0.035 31 25.4 35.5 42.5 1.398 1.220 1.000 1.673 Beamemitting part "9.4 0.370 RF-220 Reflector Accessory for the retroreflective type sensor M8 connector 2-M3020.0 5.0ן thru-hole threads RF-210 Reflector (Optional) ) 35.3 1.390 12.8 0.504 M3 nut mounting holes (for mounting at the back) Reflector 34.3 42.31.350 1.665 49.3 59.3 1.941 2.335 30 1.181 10 0.394 11 0.433 0.315 2-"3.6 "0.142 mounting holes 25 0.984 3.3 0.130 3.2 0.126 0.157 0.197 3.3 0.130 25 0.984 10 0.394 8.3 0.327 8.3 0.327 Material: Acrylic (Reflector) ABS (Base) 2-"4.6 "0.181 mounting holes RF-11 RF-12 Reflective tape (Optional) ( ) ) 30 1.181 ( Reflective tape (Optional) 0.5 0.020 30 1.181 ) 23 25 0.984 0.906 ( ) RF-13 0.7 0.028 0.7 0.028 0.315 0.236 2-"3.4 "0.134 holes, 0.236 deep (for mounting at the back) Material: Acrylic (Reflector) ABS (Base) Two M3 (length mm 0.315 in) screws with washers and two nuts are attached Material: Acrylic (Reflector) ABS (Base) 30 1.181 28 1.102 30 1.181 28 1.102 2-"3.4 "0.134 thru-holes (for mounting at the side) 2-M3 nut mounting holes (for mounting at the side) Reflective tape (Optional) ( Base 21 ( 0.827) ) 40 1.575 Reflector (Optional) 33.3 1.311 50.3 1.980 ( 8.2 0.323 0.157 Operation mode switch Stability indicator (Green) 20 0.787 0.118 Beamreceiving part 12.5 0.492 Operation indicator (Orange) Stability indicator (Green) 0.079 2.8 0.110 Sensor Rear surface Effective reflecting surface ( pressure-sensitive) adhesive Adhesive tape Effective reflecting surface Material: Acrylic Adhesive tape Reflective surface (Acrylic) Material: Acrylic 26 CX-400 DIMENSIONS (Unit: mm in) MS-CX2-1 The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/ Sensor mounting bracket (Optional) 0.197 3.4 0.134 14 0.551 12 0.472 0.118 R12 R0.472 3.4 25 0.134 R25 42.5 0.984 R0.984 1.673 t 1.2 t 0.047 3.4 0.134 13.6 0.535 25.2 0.992 14Њ 14Њ 0.315 22 0.866 15 0.591 7Њ 3.4 0.134 R12 R0.472 3.4 0.134 0.118 0.197 12 0.472 22 0.866 2-"3.4 "0.134 holes (for RF-210) 0.4 (0.016) 7Њ 10 0.394 Beam axis 20 0.787 12.5 0.492 20 0.787 0.5 0.020 Assembly dimensions Mounting drawing with the receiver of CX-41Ⅺ 25.4 1.000 31 1.220 42.5 1.673 25 0.984 9.5 0.374 Material: Stainless steel (SUS304) Two M3 (length 12 mm 0.472 in) screws with washers are attached MS-CX2-2 t 1.2 t 0.047 12.3 0.484 Sensor mounting bracket (Optional) 14 0.551 15.8 0.622 0.276 7.8 0.307 22 0.866 14 0.551 36 1.417 Assembly dimensions Mounting drawing with the receiver of CX-41Ⅺ 25 10 0.394 0.984 55 2.165 R12 R0.472 23 15.5 0.906 0.610 14Њ 4.5 0.177 t2 t 0.079 15.8 0.622 8.2 0.323 8-"3.4 "0.134 holes ( 3.6 0.142 0.157 ) 12 0.472 36 1.417 55 2.165 28 1.102 15.5 0.610 R12 R0.472 14Њ 4.5 0.177 t2 t 0.079 0.157 4.5 0.177 25.4 1.000 Beam axis 0.276 4.5 0.177 0.197 22 0.866 14 0.551 0.157 12 0.472 0.276 4.5 0.177 0.197 4.5 0.177 MS-CX2-4 8.2 0.323 7.8 0.307 Material: Stainless steel (SUS304) Two M3 (length 12 mm 0.472 in) screws with washers are attached Sensor mounting bracket (Optional) Assembly dimensions Mounting drawing with the receiver of 40Њ 20Њ CX-41Ⅺ "55 "2.165 "39 "1.535 0.236 19 29 0.748 1.142 19 0.748 0.157 3.4 0.134 SENSOR 25 0.984 25 0.984 25 0.984 "25 "0.984 R25 R0.984 Material: Stainless steel (SUS304) Two M3 (length 14 mm 0.551 in) screws with washers are attached 27 18 0.709 6.2 0.244 46 1.811 0.9 0.035 R9.5 R0.374 SENSOR 7Њ 14Њ 3.4 0.134 0.9 0.035 5.5 0.217 5.5 0.217 0.276 29 1.142 25.4 1.000 12.3 0.484 13 0.512 t 2.5 t 0.098 Beam axis 18 0.709 13 0.512 11.2 0.441 46 1.811 25 0.984 2.5 0.098 SENSOR 20Њ SENSOR 40Њ "55 "2.165 "39 "1.535 0.276 CX-400 DIMENSIONS (Unit: mm in) MS-CX2-5 15 0.591 The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/ Sensor mounting bracket (Optional) t 1.5 t 0.059 25 0.984 19 0.748 19 0.748 3.4 0.134 3.4 0.134 3.5 0.138 Assembly dimensions Mounting drawing 20.6 26.2 0.811 with the receiver of 1.031 CX-41Ⅺ 15 0.591 7Њ t 1.5 t 0.059 R19 R0.748 R25 R0.984 45 1.772 7Њ 0.197 18.9 0.744 0.197 6.5 0.256 20 0.787 0.276 37 1.457 0.276 0.315 20 0.787 37 1.457 0.197 7.9 Material: Stainless steel (SUS304) 0.311 Two M3 (length 12 mm 0.472 in) screws with washers are attached 7.9 0.311 Sensor mounting bracket (Optional) 0.5 0.020 Assembly dimensions Mounting drawing with the receiver of CX-41Ⅺ t 1.2 t 0.047 30 1.181 20.5 0.807 10Њ R25 R0.984 R25 R0.984 45 1.772 18.9 0.744 0.197 6.5 0.256 MS-CX-3 Beam axis 25.4 1.000 14 0.551 3.4 0.315 0.134 0.236 3.5 0.138 3.4 0.197 0.134 8.5 0.335 3.4 0.134 35 25 0.984 1.378 25.2 0.992 13.6 0.535 11.2 0.441 0.236 30 1.181 10Њ t 1.2 t 0.047 0.4 0.016 ( ) 8.5 0.335 Beam axis 0.354 18 0.709 31 1.220 18 0.709 3.5 0.138 4.8 0.189 20 0.787 25.4 1.000 35 1.378 0.236 R25 R0.984 10Њ 15 0.591 0.236 3.4 0.134 0.197 3.4 0.134 Material: Stainless steel (SUS304) Two M3 (length 12 mm 0.472 in) screws with washers are attached MS-RF21-1 0.315 14 0.551 Reflector mounting bracket for RF-210 (Optional) 5.5 0.217 Assembly dimensions 23 0.906 5.5 0.217 23 0.906 "36 50 "1.417 1.969 "36 50 "1.417 1.969 30Њ 10 0.394 3.2 0.126 "25 t 1.2 "0.984 t 0.047 12.5 0.492 13 0.512 30Њ 20Њ 16 0.630 3.5 0.138 10 0.394 20Њ R7.5 R0.295 46 1.811 25 0.984 46 1.811 25 0.984 13 0.512 Material: Stainless steel (SUS304) Two M3 (length 12 mm 0.472 in) screws with washers are attached 28 CX-400 DIMENSIONS (Unit: mm in) MS-RF22 The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/ Reflector mounting bracket for RF-220 (Optional) Assembly dimensions 25 0.984 25 0.984 4.5 0.177 4.5 0.177 10 0.394 28.3 19.3 1.114 0.760 11 0.433 10 0.394 35 1.378 25 0.984 35.3 1.390 0.157 8.3 0.327 16 0.630 44 10 0.394 1.732 t 1.6 t 0.063 0.315 0.236 8-M3020.0 5.0ן thru-hole threads 44.3 1.744 ( 27 (1.063) 34.3 1.350 21 0.827 ) 0.315 0.236 20 0.787 t 1.6 t 0.063 0.157 Material: Cold rolled carbon steel (SPCC) (Uni-chrome plated) Two M3 (length mm 0.315 in) screws with washers are attached MS-RF23 Reflector mounting bracket for RF-230 (Optional) Assembly dimensions 40 1.575 (0.118) 4.5 0.177 4.5 0.177 10 0.394 11 0.433 40 1.575 10 0.394 50 1.969 40 1.575 28.3 19.3 1.114 0.760 50.3 1.980 8.3 0.327 0.197 16 0.630 15 0.591 61 2.402 35 1.378 18 0.709 12 0.472 (0.118) ( 30 (1.181) ) 10 0.394 0.276 ( 26 1.024 28 1.102 ) 20 0.787 8-M4 820.0 7.0ןthru-hole threads Material: Cold rolled carbon steel (SPCC) (Uni-chrome plated) Two M4 (length 10 mm 0.394 in) screws with washers are attached 29 t2 t 0.079 49.3 1.941 61.3 2.413 37 1.457 0.276 40 1.575 0.197 t2 t 0.079 CX-400 DIMENSIONS (Unit: mm in) MS-AJ1 The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/ 17.8 0.701 12 2-"3.2 "0.126 0.472 mounting holes t2 t 0.079 2-3.2 0.126561.0 2.4ן oblong holes 0.039 11.8 0.465 20 0.787 0.236 Cable guide (POM) MS-AJ2 Universal sensor mounting stand (Optional) 28 20 1.102 0.787 0.157 33 25 20 20 1.299 0.984 0.7870.787 4.2 0.165 M4 hexagonsocket-head bolt Sensor mounting bracket [Stainless steel (SUS304)] 147 (5.787) (Note) 218 (8.583) Cable guide (POM) "10 "0.394 pipe [Stainless steel (SUS304)] 28 20 1.102 0.787 0.157 25 20 33 1.299 0.984 0.787 45Њ 0.039 Attachment (Nylon 6) 17.8 0.701 12 2-"3.2 "0.126 0.472 mounting holes t2 2-3.2 0.126561.0 2.4ן t 0.079 oblong holes 0.039 11.8 0.465 20 0.787 0.236 45Њ 3.2 0.126 Universal sensor mounting stand (Optional) 20 0.787 0.039 Attachment (Nylon 6) 45Њ 4.2 0.165 M4 hexagonsocket-head bolt Sensor mounting bracket [Stainless steel (SUS304)] 147 (5.787)(Note) 210 (8.268) 45Њ 3.2 0.126 "10 "0.394 pipe [Stainless steel (SUS304)] 2-"6.6 "0.260 mounting holes 0.315 44.5 (1.752) 28 ( 18 0.709 1.102 20 0.787 45 1.772 Base (PA) Two M3 (length 14 mm 0.551 in) screws with washers, two M3 (length 16 mm 0.630 in) screws with washers, two M3 (length 18 mm 0.709 in) screws with washers, one auxiliary mounting plate for EQ-20 series and one auxiliary mounting plate for EX-40 series are attached 25.5 1.004 32 10 1.260 0.394 2-"6.6 "0.260 mounting holes 10 0.394 ) 36.5 1.437 20 0.787 24.5 0.965 Base (PA) 32 1.260 46 1.811 20 0.787 Two M3 (length 14 mm 0.551 in) screws with washers, two M3 (length 16 mm 0.630 in) screws with washers, two M3 (length 18 mm 0.709 in) screws with washers, one auxiliary mounting plate for EQ-20 series and one auxiliary mounting plate for EX-40 series are attached 31 1.220 15 0.591 0.315 Note: The dimensions in the brackets indicate the adjustable range of the movable part Note: The dimensions in the brackets indicate the adjustable range of the movable part Assembly dimensions with CX-400 series 23.2 (Mounting part only) 0.913 Assembly dimensions with RF-210 (Reflector) (Mounting part only) 24.8 11.8 0.465 20 0.787 0.236 17.6 0.693 t2 t 0.079 11.8 0.465 20 0.787 0.236 20 28 1.102 0.787 27 1.063 0.976 18.4 0.724 t2 t 0.079 31.8 20 1.252 0.787 45Њ 2-M3 (length14 mm 0.551 in) screws with washers Center of sensing MS-AJ1-A 16.5 0.650 28.45 1.120 0.236 33.3 25 1.311 0.984 45Њ 33 25.4 1.299 1.000 45Њ 4.2 0.165 2-M3 (length14 mm 0.551 in) screws withwashers 4.2 0.165 210 8.268 134 5.276 (Note 1) 4.2 "10 "0.394 pipe 0.165 [Stainless steel (SUS304)] ( 12 0.472 Cable guide (POM) ) ( ) 33 1.299 Sensor mounting bracket [Stainless steel (SUS304)] (Note 2) Arm joint (Nylon 6) 147 2-"3.2 "0.126 5.787 mounting holes "10 "0.394 pipe (Note 1) [Stainless steel (SUS304)] 2-3.2 0.126561.0 2.4ן oblong holes ( 218 (8.583) 0.315 20 0.787 45 1.772 25.5 1.004 32 10 1.260 0.394 2-"6.6 "0.260 mounting holes 16.5 0.650 (16.5 ) 0.650 33 1.299 ) 0.236 ( Base (PA) ( 32 1.260 46 1.811 20 0.787 31 1.220 15 0.591 0.315 ) 33 (1.299) (16.5 ) 0.650 33 1.299 ) 10 0.394 36.5 (1.437) 20 0.787 Notes: 1) The dimensions in the brackets indicate the adjustable range of the movable part 2) Refer to MS-AJ1/AJ2 for the assembly dimensions with the sensor mounting bracket, sensor or reflector 210 8.268 134 5.276 (Note 1) 4.2 "10 "0.394 pipe 0.165 [Stainless steel (SUS304)] 12 0.472 Sensor mounting bracket [Stainless steel (SUS304)] (Note 2) Arm joint (Nylon 6) 147 2-"3.2 "0.126 5.787 mounting holes "10 "0.394 pipe (Note 1) [Stainless steel (SUS304)] 2-3.2 0.126561.0 2.4ן oblong holes 210 (8.268) Two M3 (length 14 mm 0.551 in) screws with washers, two M3 (length 16 mm 0.630 in) screws with washers, two M3 (length 18 mm 0.709 in) screws with washers, one auxiliary mounting plate for EQ-20 series and one auxiliary mounting plate for EX-40 series are attached 45Њ Universal sensor mounting stand (Optional) Cable guide (POM) (203.5) 8.012 Base (PA) 28.45 1.120 18 0.709 (44.5) 1.752 28 1.102 MS-AJ2-A Universal sensor mounting stand (Optional) 33 1.299 (208.5) 8.209 2-"6.6 "0.260 24.5 0.965 mounting holes Two M3 (length 14 mm 0.551 in) screws with washers, two M3 (length 16 mm 0.630 in) screws with washers, two M3 (length 18 mm 0.709 in) screws with washers, one auxiliary mounting plate for EQ-20 series and one auxiliary mounting plate for EX-40 series are attached Notes: 1) The dimensions in the brackets indicate the adjustable range of the movable part 2) Refer to MS-AJ1/AJ2 for the assembly dimensions with the sensor mounting bracket, sensor or reflector 30 DIMENSIONS (Unit: mm in) MS-AJ1-M The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.co.jp/ Universal sensor mounting stand (Optional) 22 0.866 2-M4 2-M3 11.8 0.465 17 0.669 MS-AJ2-M 11.8 0.465 M4 hexagonsocket-head bolt t t 0.079 Universal sensor mounting stand (Optional) 22 0.866 17 0.669 M4 hexagon2-M4 socket-head bolt t t 0.079 2-M3 45Њ 45Њ 25 50 40 0.984 1.575 1.969 25 40 50 0.984 1.575 1.969 45Њ Attachment (Nylon 6) 208 (8.189) ( ) 147 5.787 (Note) 45Њ 4.2 0.165 28 1.102 Attachment (Nylon 6) 20 0.787 200 ( 7.874 ) "10 "0.394 pipe [Stainless steel (SUS304)] 20 0.787 45 1.772 28 1.102 20 0.787 "10 "0.394 pipe [Stainless steel (SUS304)] 32 1.260 46 1.811 20 0.787 0.315 Two M3 (length mm 0.315 in) screws with washers and two M4 (length mm 0.315 in) screws with washers are attached 25.5 1.004 32 10 0.394 1.260 2-"6.6 "0.260 mounting holes 10 0.394 ( ) 40 1.575 20 0.787 18 0.709 1.102 ) 2-"6.6 "0.260 mounting holes Base (PA) 44.5 (1.752) 28 ( 143.5 (Note) 5.650 4.2 0.165 24.5 0.965 Base (PA) Two M3 (length mm 0.315 in) screws with washers and two M4 (length mm 0.315 in) screws with washers are attached 31 1.220 15 0.591 0.315 Note: The dimensions in the brackets indicate the adjustable range of the movable part Note: The dimensions in the brackets indicate the adjustable range of the movable part Assembly dimensions with RF-220 (Reflector) (Mounting part only) Assembly dimensions with RF-230 (Reflector) (Mounting part only) 11.8 0.465 20 0.787 55.3 2.177 38 1.496 12 0.472 M4 hexagon-sockethead bolt 71.3 2.807 47 1.850 20 0.787 11.8 0.465 t2 t 0.079 M4 hexagon-sockethead bolt t2 t 0.079 45Њ 50 1.969 45Њ 35.3 1.390 50.3 1.980 45Њ 2-M3 (length mm 0.315 in) screws with washers Protecting the environment is one of SUNX’s guiding business principles 28 1.102 45.3 1.783 4.2 28 0.165 1.102 36.3 20 1.429 0.787 45Њ 2-M4 (length mm 0.315 in) screws with washers 37 1.457 61.3 2.413 4.2 28 1.102 0.165 36.3 20 1.429 0.787 Promoting a totally lead-free ISO 14001 environmental management working environment Using simple packaging system certification acquired We are now working to eliminate the use of lead in all our in-house manufacturing processes such as in reflow ovens, hand soldering and parts and substrates procurement Simple, environmentally friendly packaging material reduces waste Our Nagoya Head Office and Factory acquired ISO 14001 certification in September 1999 Now and into the future, we will continuously improve environmental management systems based on our Environment Policy, which focuses on the promotion of environmentally friendly business activities and product development All information is subject to change without prior notice SUNX Limited 2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan Phone: +81-(0)568-33-7211 FAX: +81-(0)568-33-2631 Overseas Sales Dept http://www.sunx.co.jp/ Phone: +81-(0)568-33-7861 FAX: +81-(0)568-33-8591 Printed on 100% recycled paper PRINTED IN JAPAN No CE-CX400-1-15 July, 2004 ... Output CX- 411 CX- 411-P CX- 412 CX- 412-P CX- 491 CX- 491-P CX- 493 CX- 493-P CX- 481 CX- 481-P CX- 482 CX- 482-P CX- 424 CX- 424-P CX- 421 CX- 421-P CX- 422 CX- 422-P CX- 423 CX- 423-P CX- 441 CX- 441-P CX- 443 CX- 443-P... CX- 424-P-C5 CX- 421-C5 CX- 421-P-C5 CX- 422-C5 CX- 422-P-C5 CX- 423-C5 CX- 423-P-C5 CX- 411-Z CX- 411-P-Z CX- 412-Z CX- 412-P-Z CX- 491-Z CX- 491-P-Z CX- 493-Z CX- 493-P-Z CX- 481-Z CX- 481-P-Z CX- 482-Z CX- 482-P-Z CX- 424-Z... CX- 422-C05 CX- 422-P-C05 CX- 423-C05 CX- 423-P-C05 CX- 411-C5 CX- 411-P-C5 CX- 412-C5 CX- 412-P-C5 CX- 491-C5 CX- 491-P-C5 CX- 493-C5 CX- 493-P-C5 CX- 481-C5 CX- 481-P-C5 CX- 482-C5 CX- 482-P-C5 CX- 424-C5 CX- 424-P-C5