Tài liệu hạn chế xem trước, để xem đầy đủ mời bạn chọn Tải xuống
1
/ 19 trang
THÔNG TIN TÀI LIỆU
Thông tin cơ bản
Định dạng
Số trang
19
Dung lượng
0,96 MB
Nội dung
1
ME-430 INTRODUCTION TO COMPUTER AIDED DESIGN
Bottle –usingSurfaceFeatures
Pro/ENGINEER Wildfire 2.0
Dr. Herli Surjanhata
Create a part named bottle with three default datum planes and default coordinate
system. Make sure the Units is in millimeters.
To change the units,
From Edit pull down menu, select
Setup -> Units
Select millimeter Newton Second
(mmNs).
Set and select Interpret Existing
Numbers (Same Dims).
Click the OK button.
Close -> Done
Pick the
icon to create a sketched datum curve on the
FRONT datum plane. The dimensions for the datum curve
shown in Figure below.
2
3
Pick Right datum plane as
Mirror plane
Pick the
button to
complete the task.
Mirror the datum curve about the RIGHT datum
plane.
Select the datum curve in the Model Tree or graphic
area, then choose Edit -> Mirror
Repeat the same procedure to create another datum curve.
Create a sketched datum curve as shown
in the Figure below. Sketch on the
RIGHT datum plane with TOP as the top
reference. Make sure it is 140 mm
height, the same height as the other
curve
.
4
Mirror the last datum curve about the FRONT datum plane. The resulted curves are
shown in the Figure below.
5
Create a sketched datum curve as shown
in the Figure below. Sketch on the TOP
datum plane with RIGHT as the right
reference.
6
Pick the
icon,
Move the Sketched Datum Curve dialog
box to reveal the
icon needed to
create datum plane for sketching.
To create a datum plane on the fly, pick
the
icon, and DATUM PLANE dialog
box apprears.
Pick the TOP datum plane, and enter the
offset translation 140 mm as shown
below.
7
Pick the OK button.
Click the Sketch button.
Create a sketched circular datum curve
as shown in the Figure below.
8
The resulted datum curves are shown below.
The datum curves created above will be used to create surface feature. Select
9
From Insert pull down menu, select
Boundary Blend …
Click the Curves option as shown below.
Pick the four vertical datum curves shown on
the right figure – After picking the first curve,
press Ctrl key while selecting the rest of the
curves.
Make sure to check the Closed blend box.
10
Click the box (Click here …)
under Second direction for the
2
nd
direction chain collector.
Pick the top and bottom (circular) horizontal
curves.
Select the
to finish the surface creation.
[...]...The resulted surface is shown in the Figure on the left Create another surface at the bottom by selecting Edit pull down menu, then choose Fill … Pick the bottom curve Select the creation to finish the surface To merge the two surfaces, select two quilts from the Model tree and click the Merge Tool icon on the Features toolbar or click Edit -> Merge 11 Pick Select... Merge 11 Pick Select the , then select Join to finish to create a Pick the Round Tool icon round of 5 mm radius at the bottom edge of the surface Pick the bottom edge of the bottle Click the icon to finish To create a thin solid from a surface quilt, Select the surface quilt first from Model Tree, then Edit -> Thicken Enter thickness 1.5 Click the button to continue 12 Select all datum curves, then... Pitch = 4 mm The resulted thread is depicted below 15 Create a revolved protrusion to smooth out the top end of screw thread For sketching plane, select the end plane of the top end part of the thread – see figure below, and revolve it at 55 degrees Pick this plane as sketching plane 16 Sketch a centerline as axis of revolution Use Edge of the end thread for the section to be revolved The resulted feature . COMPUTER AIDED DESIGN
Bottle – using Surface Features
Pro/ENGINEER Wildfire 2.0
Dr. Herli Surjanhata
Create a part named bottle with three default. the
to finish the surface creation.
11
The resulted surface is shown in the
Figure on the left.
Create another surface at the bottom