Tài liệu ASM Metals HandBook P28 ppt

... Threshold Knowledge, Fatigue, Creep, and Pressure Vessels for Elevated Temperature Service, MPC-17, ASME, 1981, p 1-84 Infinite-Life Criterion (S-N Curves) Safe-life design based on the infinite-life ... diagram. This is the currently required approach for representing this type of information in that handbook. Source: Ref 21 Fig. 7 Typical constant-life diagram for solution-tre...

Ngày tải lên: 23/12/2013, 00:15

... Society for Metals, 1944; later published in Trans. ASM, Vol 34, 1945, p 71-107 Publication Information and Contributors Fractography, was published in 1987 as Volume 12 of the ASM Handbook. ... for Metals. References 1. C.A. Zapffe and M. Clogg, Jr., Fractography A New Tool for Metallurgical Research, Preprint 36, American Society for Metals, 1944; later published in Trans. AS...

Ngày tải lên: 13/12/2013, 04:15

... nitrogen, oxygen, halides, and noble gases • Direct-current plasma emission spectroscopy: Similar in performance to inductively coupled plasma emission spectroscopy • Atomic absorption spectroscopy: ... materials • Determination of trace impurity concentrations in semiconductor materials • Wear metals analysis in oils • Determination of alkali and alkaline earth concentrations in aqu...

Ngày tải lên: 13/12/2013, 04:15

... ed., Prentice Hall, 1999, p 23 2. T.H. Courtney, Materials Selection and Design, Vol 20, ASM Handbook, ASM International, 1997, p 336–356 Introduction to the Mechanical Behavior of Nonmetallic ... Adapted from Ref 3 Metals Metals represent the majority of the pure elements and form the basis for the majority of the structural materials. The mechanical behavior of metals depends...

Ngày tải lên: 13/12/2013, 04:15

Ngày tải lên: 23/12/2013, 00:15

... Foundry Mechanization With gray iron, malleable iron, and steel added to the foundrymen's metals for casting to shape, it follows that equipment and methods for the rapidly growing castings ... being given increasing attention. Molding, coremaking, sand preparation and conditioning, and metals and materials handling methods also progressed during the 1800s. To complete the story...

Ngày tải lên: 23/12/2013, 00:15

... Properties and selection [etc.] v. 13. Corrosion [etc.] v. 15. Casting. 1. Metals Handbooks, manuals, etc. I. ASM International. Handbook Committee. TA459.M43 1978 669 78-14934 ISBN 0-87170-007-7 ... suggestions are invited, and should be forwarded to ASM International. Library of Congress Cataloging-in-Publication Data (for Print Volume) Metals handbook. Includes bibliographi...

Ngày tải lên: 23/12/2013, 00:15

... increasing compressive stress The essential absence of striations on fatigue fracture surfaces of metals tested in vacuum tends to support the assumption that oxidation reduces slip reversal during

Ngày tải lên: 13/12/2013, 04:15

... effectively and efficiently. The intent of this Handbook is not to make an engineer a materials characterization specialist. During the planning of this Handbook, it became obvious that the phrase ... therefore, one of these would be a logical choice. The Handbook has been organized for ease of reference by the user. The article "How To Use the Handbook& quot; describes the tab...

Ngày tải lên: 13/12/2013, 04:15

... puremetals— [etc.]—v. 8. Mechanical testing. 1. Metals Handbooks, manuals, etc. 2. ASM International. Handbook Committee. TA459.M43 1990 620.1'6 90-115 SAN 204–7586 ISBN 0-87170-389-0 ASM ... Fabrication of Particulates Reinforced Metal Composites, ASM International, 1990, p 209 2. Alloy Phase Diagrams, Vol 3, ASM Handbook, ASM International, 1992 3. D. Hull, An Intr...

Ngày tải lên: 13/12/2013, 04:15