HƯỚNG DẪN SỬ DỤNG Mastercam x8
Hướng dẫn sử dụng phần mềm Mastercam X3 - P1
... your Mastercam Dealer Mastercam X³ Training Tutorials – & Axis Mill Applications Revised Date: September 26, 2008 Copyright © 1984 2008 In House Solutions Inc All rights reserved Software: Mastercam ... Solutions Inc Trademarks Mastercam is a registered trademark of CNC Software, Inc Microsoft, the Microsoft logo, MS, and MS DOS are registered trademarks of Microsoft Corporation; Mas...
Ngày tải lên: 30/10/2012, 14:42
Hướng dẫn sử dụng phần mềm Mastercam-X4 - P12
... Tutorials - Mill Level Applications Date: June 11, 2009 Copyright © 1984 - 2009 In-House Solutions Inc - All rights reserved Software: Mill Mastercam X4 Author: Mariana Lendel ISBN: 97 8-1 -9 2656 6-2 2-1 ... B-10 2D HS Specific Parameters B-23 Create Geometry in 3D B-28 Solids Menu B-33 Solids Manager B-34 Chaining B-36 Window ... Window Selection B-39 Chaining and Windo...
Ngày tải lên: 30/10/2012, 14:42
Hướng dẫn sử dụng phần mềm Mastercam X3 - P2
... Design Training Tutorials To order more books: Call 1-8 0 0-5 2 9-5 517 or Visit www.inhousesolutions.com or Contact your Mastercam Dealer TABLE OF CONTENTS Getting Started A1 Graphic User ... machine them Page 40 DESIGN X3 TUTORIAL NOTES: Page 41 DESIGN X3 TUTORIAL TUTORIAL QUIZ What does an extrude operation require? What are the branch points? Page 9-4 2 ... direction]: Sketc...
Ngày tải lên: 30/10/2012, 14:42
Hướng dẫn sử dụng phần mềm Mastercam X3 - P3
... QUADRANT II X- Y+ -4 .5,5.25 QUADRANT I X+ Y+ 4,4 X- -8 -7 -6 -5 -4 -3 -2 -1 -1 -2 X ORIGIN 0,0 -3 -4 -6 ,-4 -5 -6 QUADRANT III X- Y- 6.5 ,-5 .5 -7 QUADRANT IV X+ Y- -8 Y- www.inhousesolutions.com - (519) ... Third Edition - ISBN (97 8-0 -8 31 1-) 334 7-4 CNC Programming Techniques, An Insider's Guide to Effective Method...
Ngày tải lên: 30/10/2012, 14:42
Hướng dẫn sử dụng phần mềm Mastercam X3 - P4
... Oct,20 2008 Copyright © 1984 - 2008 In-House Solutions Inc - All rights reserved Software: Mastercam Mill X³ Authors: Mariana Lendel ISBN: 97 8-1 -9 2656 6-1 4-6 Notice In-House Solutions Inc reserves ... order more books: Call 1-8 0 0-5 2 9-5 517 or Visit www.inhousesolutions.com or Contact your Mastercam Dealer Mastercam X³ Training Tutorials – Indexing (Tombstone...
Ngày tải lên: 30/10/2012, 14:42
Hướng dẫn sử dụng phần mềm Mastercam X3 - P5
... represents Mastercam terminology To order Mastercam X³ Mill Level Training Tutorials books: Contact your Mastercam Dealer, Call 1-8 0 0-5 2 9-5 517 or Place an order through www.inhousesolutions.com Mastercam ... ISBN: 97 8-1 -8 9448 7-9 8-6 Notice In-House Solutions Inc reserves the right to make improvements to this manual at any time and without notice Disclaimer Of Al...
Ngày tải lên: 30/10/2012, 14:43
Hướng dẫn sử dụng phần mềm Mastercam-X4 - P17
... Router Training Tutorials To order more books: Call 1-8 0 0-5 2 9-5 517 or Visit www.inhousesolutions.com or Contact your Mastercam Dealer Mastercam X4 Training
Ngày tải lên: 30/10/2012, 14:44
Hướng dẫn sử dụng phần mềm Mastercam-X4 - P18
... Getting started page A-4 Before starting the geometry make sure that the Grid is enabled It will show you at each moment where is the part origin See Getting started page A-5 for details Select ... down arrow and Set planes to FRONT Change the depth of the plane to Z -1 .5 by entering the value in the Status Bar Page 3-9 SOLIDS X4 TUTORIAL STEP 7: CREATE ARC POLAR KNOWING THE STARTING PO...
Ngày tải lên: 30/10/2012, 14:44
Hướng dẫn sử dụng phần mềm Mastercam-X4 - P1
... 7-1 Swarf 5-Axis With Wall Defined By Using Contours Tutorial 8-1 Flow 5-Axis Tutorial 9-1 Multisurface 5-Axis Tutorial 1 0-1 Port 5-Axis Tutorial 1 1-1 ... Tutorial . 3-1 Chuck Indexing Tutorial 4-1 Rotary4-Axis Toolpath and Axial 4ax Tutorial 5-1 Curve 5-Axis Tutorial 6-1 Drill 5-Axis and Circle Mill 5-Axis Tutorial ... 8, 2009 Copyright © 1984 - 2009 In-House Solut...
Ngày tải lên: 30/10/2012, 14:44