Planning in parallel machine shops and scheduling of flexible process plans in mould manufacturing shop

... COMBINED PLANNING IN PARALLEL MACHINES 62 5.1 Planning in Single stage system ………………………………62 5.1.1 Separation of Sequencing and Scheduling in parallel machines ……63 5.1.2 New approach for combined ... Review shop, group of parallel machine shop and FMC scheduling problems will come under NP-hard problems Both the single stage parallel machine shops and...

Ngày tải lên: 28/11/2015, 13:53

... MODELLING AND SCHEDULING OF HETEROGENEOUS COMPUTING SYSTEMS LIU GUOQUAN (M Eng., Tsinghua University) A THESIS SUBMITTED FOR THE DEGREE OF DOCTOR OF PHILOSOPHY DEPARTMENT OF INDUSTRIAL AND SYSTEMS ... 143 Chapter Modelling and Analysis of Service Reliability for Distributed Computing Systems .145 7.1 Centralized heterogeneous distributed system (CHDS) and...

Ngày tải lên: 16/09/2015, 15:53

... FABRICATION AND OPTIMIZATION OF FLEXIBLE DYE SENSITIZED SOLAR CELLS Xue Zhaosheng (B.Appl.Sc.(Hons), NUS) A THESIS SUBMITTED FOR THE DEGREE OF DOCTOR OF PHILOSOPHY NUS GRADUATE ... about half of the crystalline silicon solar cells Table 1.2 Comparison of various types of solar cells and their challenges[4, 30] acells with active area of at least cm2 Eff...

Ngày tải lên: 10/09/2015, 09:11

... ANALYSIS AND DESIGN OF FLEXIBLE SYSTEMS TO MANAGE DEMAND UNCERTAINTY AND SUPPLY DISRUPTIONS GEOFFREY BRYAN ANG CHUA (M.Sci., University of the Philippines) A THESIS SUBMITTED FOR THE DEGREE OF ... Asymptotic Sale Ratio for Various Levels of Safety Capacity and Demand Uncertainty 52 2.6 Asymptotic Chaining Efficiency for Various Levels of Partial Flexibil...

Ngày tải lên: 14/09/2015, 08:39

... representations of the position of the flexible link By generalizing the modeling of single link robot, the modeling of a n -link robot is presented From the simulation results of the proposed controller ... can be directly controlled by motors, and thus the number of the variables to be controlled is equal to the number of the control inputs For flexible link...

Ngày tải lên: 26/11/2015, 12:31

... presented our study of the optimal planning and sequencing for parallel machining operations The combinatorial nature of sequencing and the complication of having precedence and mode constraints ... 8 Soft Computing for Optimal Planning and Sequencing of Parallel Machining Operations Yuan-Shin Lee‫ء‬ North Carolina State University ... cycle t...

Ngày tải lên: 25/12/2013, 19:15

... Good practices in planning and management of integrated commercial poultry production in South Asia by R Prabakaran Professor of Poultry Science Tamil Nadu Veterinary and Animal Science ... researchers and those involved in development in general Good Practices in Poultry Production in South Asia Chapter Poultry Industry in South...

Ngày tải lên: 21/02/2014, 01:20

... accessing services and often want to access them out of the borough’ The problem of gaps in service provision Asked why the provision of mental health services for refugees and asylum seekers in London ... contributing factors to the long-term mental health of refugees and asylum seekers The fundamental challenges faced by service pr...

Ngày tải lên: 24/02/2014, 18:20

... Volumes by CT and PET -CT in 13 Patients with Malignant Pleural Mesothelioma Volume, cc GTV Mean ± S.D Min-max CTV Mean ± S.D Min-max PTV1 Mean ± S.D Min-max PTV2 Mean ± S.D Min-max CT PET -CT P Value ... on the CT and integrated PET -CT images The GTV was defined as the volume of macroscopic primary tumor and involved hilar and mediastinal lymph nodes identifie...

Ngày tải lên: 09/08/2014, 10:20

... article as: Morris et al., A multi-center, randomized, double-blind, parallel, placebo-controlled trial to evaluate the efficacy, safety, and pharmacokinetics of intravenous ibuprofen for the treatment ... demonstrates baseline data There were no differences among the four arms of the study in baseline demographics Also, analyses of baseline d...

Ngày tải lên: 13/08/2014, 21:20

... Main Contributions  Application of Controllability Rank Condition Theorem resulting in a general result on the controllability of nonholonomic robots  Application to multibody mobile robots ... Model   Constraints  G ( q, q, t ) =  ω (q) ⋅ q = Are constraints of the above form nonintegrable /nonholonomic? (integrability) Do constraints of the above form “re...

Ngày tải lên: 26/10/2014, 14:38

Ngày tải lên: 17/03/2015, 12:53