Mechanical Engineers Data Handbook Episode 13 ppsx
Mechanical Engineers Data Handbook Episode 13 ppsx
... screw Socket shoulder head screw MECHANICAL ENGINEER'S DATA HANDBOOK -1 Eye bolt indented foundation bon Rawlbon 290 MECHANICAL ENGINEER’S DATA HANDBOOK 8. I .2 Abbreviations ... 20,25,30,35,40,45,50,55,60,65,70,75,80,90, 100, 110, 120, 130 , 140, 150 Standard screw lengths 10, 12, 16, 18, 20,22, 25, 30, 35,40,45, 50, 55,60, 70. 306 MECHANICAL ENGINE...
Ngày tải lên: 13/08/2014, 09:21
Mechanical Engineers Data Handbook Episode 1 ppsx
... Publication Data Carvill, James Mechanical Engineer’s Data Handbook I. Title 62 1 Library of Congress Cataloguing in Publication Data Carvill, James Mechanical engineer’s data handbook/ James ... G Note: A is parallel to the direction of P. I P Mechanical Engineer’s Data Handbook 10 MECHANICAL ENGINEER’S DATA HANDBOOK Bolted joint in tension .+...
Ngày tải lên: 13/08/2014, 09:21
Mechanical Engineers Data Handbook Episode 3 ppsx
... after blast-off g=acceleration due to gravity (assumed to be constant) 40 MECHANICAL ENGINEER’S DATA HANDBOOK I .6.3 Strength of keys and splines A key is used to prevent a machine ... for use on tapered shafts, and the inexpensive ‘saddle’ and ‘round’ keys. 48 MECHANICAL ENGINEER’S DATA HANDBOOK Maximum compressive stress U, =My+! IA Le = actual length o...
Ngày tải lên: 13/08/2014, 09:21
Mechanical Engineers Data Handbook Episode 6 ppsx
... Undercooling RE p Undercooling RE h 3 .13. 3 Gas refrigeration cycle Referring to the T-s diagram: 132 MECHANICAL ENGINEER’S DATA HANDBOOK Thermal conductivity coefficients (W ... -am 4 P 1 speed. N Power, MEP, mechanical efficiency vs speed Max. '\i power Max. economy 124 MECHANICAL ENGINEER'S DATA HANDBOOK 3. I I Air compressors T...
Ngày tải lên: 13/08/2014, 09:21
Mechanical Engineers Data Handbook Episode 9 ppsx
... 210 MECHANICAL ENGINEER’S DATA HANDBOOK 5. I I .5 Flame cutting Steel plate over 300mm thick can be cut ... joining brass and copper. It is in strip form and is used with a flux powder. 200 MECHANICAL ENGINEER’S DATA HANDBOOK Vehicle axle FORGINGS 5.9.2 Drawing process This is the forming ... r+- , (6 in degrees) 2” :( :) When r=2t, c= 3tan 0.02188 t....
Ngày tải lên: 13/08/2014, 09:21
Mechanical Engineers Data Handbook Episode 15 ppsx
... stock Miscellaneous data Glossary Index An knprlnt of Elsevier Science www.bh.com ISBN 0-7506-1960-0 9 780750 619608 342 MECHANICAL ENGINEER’S DATA HANDBOOK Water, (confinued) ... 207 recommended usage, 214 bracket welds, 13 butt welds, 13, 21 1-12 factors of safety, 309 fillet welds, 13 stress allowable, 216 symbols, 213 tack welds. 21 I termino...
Ngày tải lên: 13/08/2014, 09:21
Mechanical Engineers Data Handbook Episode 2 pot
... - 1 so 1.72 1.86 1.99 2 .13 - - 1.43 1.39 1.62 1.56 1.73 1.64 1.84 1.74 1.95 1.84 - 1.36 1.53 1.59 1.67 1.76 22 MECHANICAL ENGINEER’S DATA HANDBOOK r P 0 d P Bending ... 1 J2nJzZ3z Simply supported beam, non-central mass f= 1/2nJz&m 28 MECHANICAL ENGINEER'S DATA HANDBOOK ! Bending of thick curved bars, rings and crane hooks R I...
Ngày tải lên: 13/08/2014, 09:21
Mechanical Engineers Data Handbook Episode 4 pdf
... ZD 1 tan@ + 4) Mechanical advantage MA= 1 RD Velocity ratio VR = - = - tan0 p MA tan0 VR tan@ + 4) Efficiency = - = 76 MECHANICAL ENGINEER’S DATA HANDBOOK Effective ... pad A=pad area Torque capacity (2 pads) T= 2pFr F Pad pressure p=- A 80 MECHANICAL ENGINEER’S DATA HANDBOOK Definition of simple harmonic motion Referring to the figure, po...
Ngày tải lên: 13/08/2014, 09:21
Mechanical Engineers Data Handbook Episode 5 pps
... 2203 m2 s- y= 1.40 P,=0.711 112 MECHANICAL ENGINEER’S DATA HANDBOOK Fluid n IC Air (n=y) 1.4 0.528 Initially dry saturated steam 1 .135 0.577 Initially superheated steam ... shown. 3.4 Data tables 3.4. I Temperature conversion Conversion formulae : "F - 32 OC=- 1.8 'F=('Cx 1.8)+32 98 MECHANICAL ENGINEER'S DATA HANDBOOK Let:...
Ngày tải lên: 13/08/2014, 09:21
Mechanical Engineers Data Handbook Episode 7 pptx
... If x = 0.84~ + 0.3 135 s + 0.357n +0.0728ERS + 27.4R y = x + 5h (using E = 0 for a stoichiometric air/fuel ratio) 148 MECHANICAL ENGINEER’S DATA HANDBOOK 4.2 Flow of ... f= friction coefficient y = ratio of specific heats p = density 156 MECHANICAL ENGINEER'S DATA HANDBOOK Kinematic viscosity Dynamic viscosity Density Kinematic viscos...
Ngày tải lên: 13/08/2014, 09:21