The Design of Rolling Bearing Mountings (FAG Bearing Co) Episode 9 ppt

... professor about the error. The professor then picked up the transparency and turned it right side up, but it was still backwards. The audience chuckled. On the third try, the professor placed the ... to the hull; the crew had not practiced filling or lowering the lifeboats; earlier in the evening, the wireless operators of the Titanic had chastised the wireless o...

Ngày tải lên: 12/08/2014, 08:21

... preloading the bearings in the axial direction. The bearing seats on the shaft and in the end cap bores must be well aligned. To allow the spring washer to adjust the bearings axially, the outer ... clearance Due to the tight fits, the inner ring of the bearing is expanded and the outer ring with the roller-and-cage assembly is contracted. Thus the radial c...

Ngày tải lên: 13/08/2014, 05:21

... arranged. Bearing selection The axial load of 130 kN is made up of the weight of the rotor and the two variable top and bottom fan im- pellers as well as the thrust of these fan impellers. They are ... accuracy of the workpiece mainly depend on the axial rigidity of the spindle headstock and of the rotary table. Therefore, the rigidity of the thrust bea...

Ngày tải lên: 13/08/2014, 05:21

... 23248B.MB (bearing location 3) at the coupling end of the input shaft and the spher- ical roller thrust bearing 294 64E (bearing location 9) at the output end of the output shaft. Based on the index of ... The effects of basing the bearing dimensions on attain- able life become evident in the case of the two bearings dimensioned for the least load carry...

Ngày tải lên: 13/08/2014, 05:21

... shoulder and bearing cup. The cones are cir- cumferentially loaded. But only the cone of the larger bearing can be press-fitted. The cone of the smaller bearing is slide-fitted because the bearings ... rings protect the bearing unit from the penetration of water in the seating area of the cup. 46: Axle box roller bearings of the ICE driving unit 37 Dri...

Ngày tải lên: 13/08/2014, 05:21

... bearing at the pinion end. It accommo- dates the high radial loads. The machined cage of the bearing is guided at the outer ring. The bearing has the increased radial clearance C3 since the bearing ... diameter depends on size and speed of the ship as well as on the type and size of the rudder used. The bearing bore and the size of the bearing a...

Ngày tải lên: 13/08/2014, 05:21

... housing) The Design of Rolling Bearing Mountings PDF 5/8: Paper machines Lifting and conveying equipment Rolling Bearings FAG OEM und Handel AG Publ. No. WL 00 200/5 EA The Design of Rolling Bearing ... depends on the type of paper, its thickness and speed, and on the number of dryer rolls). The high temperatures of the heating steam transfer to the be...

Ngày tải lên: 13/08/2014, 05:21

... (underground mining) These sheaves are arranged in the head frames of the pits. The rope fastened to the cage runs from the drive sheave or the drum of the hoist into the mine by pass- ing over the rope ... deformations of the head frame. Machining tolerances One bearing acts as the locating bearing, the other one as the floating bearing. Both bearings have...

Ngày tải lên: 13/08/2014, 05:21

... BNM3234KR.132887. One of the plummer blocks is designed as the floating bearing (closed on one side, design AL), the other one as the locating bearing (continuous shaft, design BF). The unsplit housings of series ... sealing The grease in the bearing (FAG rolling bearing grease Arcanol L186V) is renewed at intervals of 1 1/2 to 2 years coinciding with th...

Ngày tải lên: 13/08/2014, 05:21

... factor in the selec- tion of the bearing size is the diameter of the individu- al gear shafts determined in the strength calculation. The two largest cylindrical roller bearings of the gear are ... the minimum value F rmin during one revolution of the eccentric shafts. For calculation of these loads, the distance R between the centres of gravity of imbala...

Ngày tải lên: 13/08/2014, 05:21