McGraw-Hill Machining and Metalworking Handbook 3rd ed - R Walsh D Cormier (McGraw-Hill 2006) WW Part 12 potx
mcgraw hill machining and metalworking handbook 3rd ed r walsh d cormier mcgraw hill 2006 ww 9 pptx
... for Machinists and Metalworkers 31
Walsh CH02 8/30/05 9:11 PM Page 31
Downloaded from Digital Engineering Library @ McGraw-Hill (www.digitalengineeringlibrary.com)
Copyright © 2004 The McGraw-Hill ... near-net-shape processes, rough
1
1
Walsh CH01 8/30/05 8:39 PM Page 1
Downloaded from Digital Engineering Library @ McGraw-Hill (www.digitalengineeringlibrary.com)
Copyright © 2004 T...
McGraw-Hill Machining and Metalworking Handbook 3rd ed - R. Walsh_ D. Cormier (McGraw-Hill 2006) WW Part 1 pptx
... Ronald A. Walsh.
and Denis R. Cormier 3rd ed.
p
. cm.
ISBN 0-0 7-1 4578 7-9
1. Machining Handbooks, manuals, etc. 2. Metal-work—Handbooks,
manuals, etc. I. Cormier, Denis R. II. Title.
TJ1185.W35 ... turning operations.
Electric discharge machining (EDM). EDM comes in two forms—sinker
EDM and wire EDM. Sinker EDM uses spark erosion to machine a
workpiece with a graphi...
McGraw-Hill Machining and Metalworking Handbook 3rd ed - R. Walsh_ D. Cormier (McGraw-Hill 2006) WW Part 2 potx
... 248
SACD
‡
99 000 680 76 000 520 10
40 197 45
* ACD represents annealed cold drawn.
†
NCD represents normalized cold drawn.
‡
SACD represents spheroidized annealed cold drawn.
SOURCE: Reprinted with ... and other chapters of this Handbook are extracted
from the latest standards of the ASTM, SAE, and AGMA.
There are a tremendous number of different engineering materials
for which the AST...
McGraw-Hill Machining and Metalworking Handbook 3rd ed - R. Walsh_ D. Cormier (McGraw-Hill 2006) WW Part 3 pot
... heat-treated.
SAE/AISI 12L14. Low-carbon, resulfurized, rephosphorized,
and leaded steel used for screw-machine parts such as studs, nuts,
and various fasteners. Can be case-hardened.
SAE/AISI 121 5. ... Similar to 12L14 and low-carbon steel used
for studs, nuts, and fasteners. Can be case-hardened.
SAE/AISI 12L15. Leaded version of 121 5 used for screw-
machine parts. Can be case-h...
McGraw-Hill Machining and Metalworking Handbook 3rd ed - R. Walsh_ D. Cormier (McGraw-Hill 2006) WW Part 4 docx
... NR F 709–790 E G NR NR NR NR NR NR F 100 S Automatic screw-machine The standard free-cutting
parts and carburetor, brass and its machinability
magneto parts, radiator has become the standard
drums ... together
and ornamental work, with moderate cold-
pump and power cylin- working properties.
ders and liners.
211
Walsh CH04 8/30/05 9:33 PM Page 211
Downloaded from Digital Engineeri...
McGraw-Hill Machining and Metalworking Handbook 3rd ed - R. Walsh_ D. Cormier (McGraw-Hill 2006) WW Part 6 potx
... increase
feed.
Condition: Crater wear
Remedy: Use aluminum oxide–coated grade; use cermets; reduce
speed; reduce feed.
Condition: Dull surface finish
Remedy: Increase speed; use positive-rake ... aluminum oxide–coated
grade; increase feed; increase coolant concentration; increase
depth of cut.
Condition: Thermal deformation
Remedy: Use more wear-resistant grade; reduce speed; reduce
feed.
Too...
McGraw-Hill Machining and Metalworking Handbook 3rd ed - R. Walsh_ D. Cormier (McGraw-Hill 2006) WW Part 8 pps
... include
■
Helical hooded dressers
■
Abrasive wheel dressers
■
Single-stone diamond dressers
■
Multiple-point diamond dressers
■
T-type diamond hand dressers
■
Diamond-stick dressers (silicon carbide)
■
Dressing ... dies
■
Locknut-thread round adjustable dies
Taps and dies are made from carbon steel, HSS, and solid carbide
(plain or titanium nitride coated). Taps and dies are made for A...
McGraw-Hill Machining and Metalworking Handbook 3rd ed - R. Walsh_ D. Cormier (McGraw-Hill 2006) WW Part 10 ppsx
... commercial bright and extralight matte.
Stretcher leveled. Uniform, high-quality matte sheets, further
processed by stretching to provide superior flatness. Furnished
resquared or not resquared. Resquared ... metal part is sheared and punched, it may require
a press-brake operation to form flanges or produce hemmed edges.
Figure 9.4 shows a small press brake that has a digital readout f...
McGraw-Hill Machining and Metalworking Handbook 3rd ed - R. Walsh_ D. Cormier (McGraw-Hill 2006) WW Part 12 potx
... manufactured
today.
12. 5.3 Design of molded plastic parts
Final selection of plastic type and part configuration or design should
be reviewed and coordinated with the mold maker and plastic part
manufacturer before ... final design drawings are made. Mold
makers and molded -part manufacturers can alert the designer to
the many problem areas that are prevalent on preliminary des...
McGraw-Hill Machining and Metalworking Handbook 3rd ed - R. Walsh_ D. Cormier (McGraw-Hill 2006) WW Part 14 docx
... Techniques and Hardware
Welding procedures and electrode sizes. The correct electrode size is
one that, when used with the proper amperage and travel speed,
produces a weld of the required size in ... Figure 14.38 shows the sizes
and dimensions of standard clamp-collars, and Fig. 14.39 shows
the data for the internally threaded clamp-collar series.
Split-collars and threaded split...