IADC Drilling Manual Part 5 docx
IADC Drilling Manual Part 5 docx
... G1-3b
F-14
International Association of Drilling Contractors
IADC Drilling Manual - Eleventh Edition
E-12
International Association of Drilling Contractors
IADC Drilling Manual - Eleventh Edition
Table ... Association of Drilling Contractors
IADC Drilling Manual - Eleventh Edition
Figure E5-1c Surface Radii on Hook & Swivel Ball
These recommendations cover hoisting...
IADC Drilling Manual Part 1 pdf
... (Blocks) F -5
12
International Association of Drilling Contractors
IADC Drilling Manual - Eleventh Edition
E. Centrifuges Y -50
III. Surface Circulating Equipment Y -55
A. Introduction Y -55
B. Considerations ... Glossary Z-1
IADC Glossary - A Z-3
IADC Glossary - B Z-4
IADC Glossary - C Z-7
IADC Glossary - D Z-10
IADC Glossary - E Z-13
IADC Glossary - F Z-13
IADC Glo...
IADC Drilling Manual Part 2 ppsx
... Association of Drilling Contractors
IADC Drilling Manual - Eleventh Edition
Figure B1- 15
Figure B1-16
Figure B1-17
B-12
International Association of Drilling Contractors
IADC Drilling Manual - Eleventh ... B- 150
V. Drill String Maintenance B- 151
VI. Drill String Operating Limits B- 151
B-8 Glossary Of Drill String Terms B- 154
B-28
International Association of Drillin...
IADC Drilling Manual Part 3 pdf
... 4" 313 490 244 640 211 350
4-1/2" 373 52 0 291 57 0 251 890
5& quot; 442 420 3 45 910 299 160
B-144
International Association of Drilling Contractors
IADC Drilling Manual - Eleventh Edition
Values ... Contractors
IADC Drilling Manual - Eleventh Edition
MAXIMUM TORSIONAL LOAD (ft-lbs)
3-1/2" 20 160 15 360 13 130
4" 25 480 19 690 16 930
4-1/2" 3...
IADC Drilling Manual Part 4 pptx
... Contractors
IADC Drilling Manual - Eleventh Edition
Figure D1-3 Bending Strength Ratios of 1-1/2" and 1-3/4" Drill Collars
D-22
International Association of Drilling Contractors
IADC Drilling Manual ... Association of Drilling Contractors
IADC Drilling Manual - Eleventh Edition
Notes on Table D1-1
* The drill collar number (column 1) consists of two parts separ...
IADC Drilling Manual Part 6 pot
... Association of Drilling Contractors
IADC Drilling Manual - Eleventh Edition
Figure J3-4 File-Gard Rod in Corrosive Drilling Fluid
FIGURE J3-4: This File-Gard rod was run in a corrosive drilling fluid.
Notice ... inlet.
H-14
International Association of Drilling Contractors
IADC Drilling Manual - Eleventh Edition
H4. Inspection
I. Inspection
All hoisting tools on the rotary...
IADC Drilling Manual Part 7 ppt
... plug.
J- 95
International Association of Drilling Contractors
Chapter J: Pumps
This Page Left Intentionally Blank
K-12
International Association of Drilling Contractors
IADC Drilling Manual ... above a standard 5 inch API NC50 connection hung in the bottom pipe ram
as illustrated in Figure K1-4C.
J-86
International Association of Drilling Contractors
IADC Dril...
IADC Drilling Manual Part 8 doc
... of Drilling Contractors
IADC Drilling Manual - Eleventh Edition
Table K1-8-7 Cameron Ram BOPs - Operating Characteristics
K-88
International Association of Drilling Contractors
IADC Drilling Manual ... be
K-82
International Association of Drilling Contractors
IADC Drilling Manual - Eleventh Edition
Table K1-8 -5 Hydril Ram BOPs - Operating Characteristics
L-7
Internat...
IADC Drilling Manual Part 9 ppt
... M -54
International Association of Drilling Contractors
IADC Drilling Manual - Eleventh Edition
Cut-Off Program For 1" Rotary Drilling Line; Goal of 9.0 T-M/Ft Cut
Table - M5-p3b Wire ... until one entire drilling line (requiring no long cuts) has been used following this particular
program.
M -56
International Association of Drilling Contractors
IADC Drilling Manual...
IADC Drilling Manual Part 11 ppsx
... Nomenclature(R13-8a, R13-8b, R13-8c)
DP = p Q
2
/ {10 858 (An)
2
}
= 9 .5 x (300 x 300) / {10 858 (0.2 155 x 0.2 155 )}
= 855 ,000 / (50 4. 25) = 16 95 psi.
Record "16 95& quot; psi on line 13 of the work sheet.
See ... from R13-1. Equ. in Hydraulic Calculations
V = 24 .5 Q/{(Dh)
2
- (Dp)
2
} = 24 .5 x 300 / {(8 .5 x 8 .5) - (4 .5 x 4 .5) }
= 7 350 / {72. 25 - 20. 25} = 141 ft/...
Từ khóa:
- thiết kế bài giảng lịch sử 8 tập 1 part 5 docx
- tự học indesign cs2 layout part 5 docx
- bài tập vật liệu xây dựng part 5 docx
- 50 harvard essays part 5
- toefl cbt book part 5
- writing template part 5
- reading upper intermediate part 5
- teaching academic esl writing part 5
- kaplan toefl paper and pencil part 5