IADC Drilling Manual Part 2 ppsx
IADC Drilling Manual Part 2 ppsx
... of Drilling Contractors IADC Drilling Manual - Eleventh Edition Table B2-3 Class 2 DP - Torsion, Tension, Collapse, Internal Pressure B -24 International Association of Drilling Contractors IADC ... Association of Drilling Contractors IADC Drilling Manual - Eleventh Edition Figure B1-15 Figure B1-16 Figure B1-17 B- 12 International Association of Drilling Contractors...
Ngày tải lên: 11/08/2014, 08:21
IADC Drilling Manual Part 11 ppsx
... Association of Drilling Contractors Chapter P: Hole Deviation and Horizontal Drilling Figure P2-4 Zone Selection Map P- 82 International Association of Drilling Contractors IADC Drilling Manual - Eleventh ... tensile load while drilling. With medium-radius wells, there is typically no tensile load while drilling. R -2 International Association of Drilling Contractors IADC...
Ngày tải lên: 11/08/2014, 08:22
IADC Drilling Manual Part 1 pdf
... Z-18 IADC Glossary - J Z-19 IADC Glossary - K Z -20 IADC Glossary - L Z -20 IADC Glossary - M Z -21 IADC Glossary - N Z -23 IADC Glossary - O Z -23 IADC Glossary - P Z -24 IADC Glossary - Q Z -26 IADC ... N -20 V. Grease Applications N -21 VI. Thread Lubricants N -22 VII. Blow-out Preventers N -22 VIII. Machinery Storage N -22 IX. Lubricant Storage N -22 X. Summary N -...
Ngày tải lên: 11/08/2014, 08:21
IADC Drilling Manual Part 3 pdf
... Class Class 2 Pipe New (80% Nom. Wall) (70% Nom. Wall) 3-1 /2& quot; 29 7 660 23 0 490 198 300 4" 313 490 24 4 640 21 1 350 4-1 /2& quot; 373 520 29 1 570 25 1 890 5" 4 42 420 345 910 29 9 160 B-144 International ... Drilling Contractors IADC Drilling Manual - Eleventh Edition MAXIMUM TORSIONAL LOAD (ft-lbs) 3-1 /2& quot; 20 160 15 360 13 130 4" 25 480...
Ngày tải lên: 11/08/2014, 08:21
IADC Drilling Manual Part 4 pptx
... Contractors IADC Drilling Manual - Eleventh Edition Figure D1-3 Bending Strength Ratios of 1-1 /2& quot; and 1-3/4" Drill Collars D -22 International Association of Drilling Contractors IADC Drilling Manual ... size (Example: 8" (20 3 .2 mm) OD in 12- 1/4" (311 .2 mm) hole, 6" (1 52. 4 mm) OD in 8-1/4" (20 9.6 mm) hole, avoid B.S.R.'s above 2. 8...
Ngày tải lên: 11/08/2014, 08:21
IADC Drilling Manual Part 5 docx
... Association of Drilling Contractors IADC Drilling Manual - Eleventh Edition E- 12 International Association of Drilling Contractors IADC Drilling Manual - Eleventh Edition Table E2-1 Master and ... collar is used for drilling, however, it wears as shown in Figure E3 -2. E-18 International Association of Drilling Contractors IADC Drilling Manual - Eleventh Edition Fi...
Ngày tải lên: 11/08/2014, 08:21
IADC Drilling Manual Part 6 pot
... condition. J -24 International Association of Drilling Contractors IADC Drilling Manual - Eleventh Edition Figure J3 -2 Proper Clearance Under Pressure Promotes Piston Life FIGURE J3 -2: Proper clearance ... difficulty. a. Oil. 1. Insufficient oil. 2. Dirty filters, oil coolers, or sump screen. J -22 International Association of Drilling Contractors IADC Drilling Manual -...
Ngày tải lên: 11/08/2014, 08:21
IADC Drilling Manual Part 7 ppt
... will do the job required at the lowest speed. K -28 International Association of Drilling Contractors IADC Drilling Manual - Eleventh Edition a. Before drilling out any casing shoe, test entire casing ... plug. J-95 International Association of Drilling Contractors Chapter J: Pumps This Page Left Intentionally Blank K- 12 International Association of Drilling Co...
Ngày tải lên: 11/08/2014, 08:22