The Design of Rolling Bearing Mountings Part 15 pdf
The Design of Rolling Bearing Mountings Part 15 pdf
... way that the pressure cone apex of the left-hand bearing points to the left and the pressure cone apex of the right-hand bearing points to the right. With the O arrangement one of the bearing ... bearing rings). The term "static", therefore, relates to the operation of the bearings but not to the effects of the load. The magnitude and di...
Ngày tải lên: 11/08/2014, 05:22
The Design of Rolling Bearing Mountings Part 4 pdf
... shaft Engine-end bearing: The roller and cage assembly runs directly on the out- put shaft and in the bore of the input shaft. The cage is guided by the rolling elements. The logarithmic profile of the rollers ... Depending on the direction of rotation of the worm shaft, either one or the other bearing accommodates the axial load. A cylindrical roller be...
Ngày tải lên: 11/08/2014, 05:22
The Design of Rolling Bearing Mountings Part 9 pdf
... deformations of the head frame. Machining tolerances One bearing acts as the locating bearing, the other one as the floating bearing. Both bearings have a tapered bore (K 1:12). They are mounted on the ... loading on the thrust bearing. The spheri- cal roller bearing size depends on that of the spherical roller thrust bearing. The outside diameter of the rad...
Ngày tải lên: 11/08/2014, 05:22
The Design of Rolling Bearing Mountings Part 11 pdf
... BNM3234KR.132887. One of the plummer blocks is designed as the floating bearing (closed on one side, design AL), the other one as the locating bearing (continuous shaft, design BF). The unsplit housings of series ... as outer bearings and FAG 23176K.MB as inner bearings. The pitman bearing arrangement is of the floating bearing type. The outer bearing arran...
Ngày tải lên: 11/08/2014, 05:22
The Design of Rolling Bearing Mountings Part 1 potx
... ceramic coating on the outer ring O.D.s and faces. Ventilation end Drive end 2: Traction motor of an electric commuter train The Design of Rolling Bearing Mountings PDF 1/8: Contents Rolling Bearings FAG ... to M6 The bearings are fitted tightly on the shaft due to the high load, which is sometimes of the shock type. This reduces the danger of fretting corros...
Ngày tải lên: 11/08/2014, 05:22
The Design of Rolling Bearing Mountings Part 2 docx
... pres- sure in the rolling contact area of the bearing is rela- tively low (p 0 ≤ 2,000 N/mm 2 ), and the bearings are failsafe. Consequently, the service life of the bearings is dictated by the grease ... arranged. Bearing selection The axial load of 130 kN is made up of the weight of the rotor and the two variable top and bottom fan im- pellers as well as...
Ngày tải lên: 11/08/2014, 05:22
The Design of Rolling Bearing Mountings Part 3 docx
... accuracy of the workpiece mainly depend on the axial rigidity of the spindle headstock and of the rotary table. Therefore, the rigidity of the thrust bear- ings is especially important. To increase the ... conditions as the expansion of the rotating parts due to the effects of heat and centrifugal force do not cause jamming of the outer rings in the housi...
Ngày tải lên: 11/08/2014, 05:22
The Design of Rolling Bearing Mountings Part 5 docx
... for the oil for the pinion shaft particularly for the bearing on the flange side. Attention should be paid to the oil flow di- rection which is always from the small end to the large end of the ... wheel bearings. An oiltight, welded housing protects gear and bearings against contamination. 37: Rear wheel of a truck The Design of Rolling Bearing Mountings PD...
Ngày tải lên: 11/08/2014, 05:22
The Design of Rolling Bearing Mountings Part 6 pot
... second floating bearing, a cylindrical roller bearing FAG NJ215E, is at the motor end of the input shaft. The locating bearing arrangement of the input shaft is an angular contact ball bearing pair FAG 7215B.UA70 ... Lubrication All the bearings of the transmission are lubricated by the oil circuit of the gearings. Suspension bearing arrangement 53 for ele...
Ngày tải lên: 11/08/2014, 05:22
The Design of Rolling Bearing Mountings Part 7 pot
... bearing at the pinion end. It accommo- dates the high radial loads. The machined cage of the bearing is guided at the outer ring. The bearing has the increased radial clearance C3 since the bearing ... diameter depends on size and speed of the ship as well as on the type and size of the rudder used. The bearing bore and the size of the bearing a...
Ngày tải lên: 11/08/2014, 05:22