The Design of Rolling Bearing Mountings Part 6 pot
The Design of Rolling Bearing Mountings Part 6 pot
... N6 P6 Lubrication All the bearings of the transmission are lubricated by the oil circuit of the gearings. Suspension bearing arrangement 53 for electric goods train locomotive The torque of ... cir- cumferential load and have therefore a tight fit in the rotating bullgear. The axial clearance of the bearing pair depends on the machining tolerances of the...
Ngày tải lên: 11/08/2014, 05:22
The Design of Rolling Bearing Mountings Part 1 potx
... HJ318E.F1 serves as the locating bearing. The cylindrical roller bearing FAG 566 513 is an NJ318E.TVP2.P64.F1, but its inner ring is 6 mm wider. The resulting axial clearance of 6 mm is required in ... corrosion, particularly at the drive end. Bearing clearance Due to the tight fits, the inner ring of the bearing is expanded and the outer ring with the rolle...
Ngày tải lên: 11/08/2014, 05:22
The Design of Rolling Bearing Mountings Part 7 pot
... bearing at the pinion end. It accommo- dates the high radial loads. The machined cage of the bearing is guided at the outer ring. The bearing has the increased radial clearance C3 since the bearing ... ring: Shaft m6, ring R6 (S7) Tapered roller bearing of ring gear shaft: Shaft n6 – p6 housing K6 – M6 The axial clearance of the tapered roller bearing pai...
Ngày tải lên: 11/08/2014, 05:22
The Design of Rolling Bearing Mountings Part 8 pot
... 5 kN/m. Bearing selection, dimensioning The diameter of the suction box is decisive for the size of the bearing. We recommend bearings with a dynam- ic load rating as low as possible; the higher ... ring prevent water penetrating from the outside. 66 : Suction roll bearings Floating bearing Locating bearing 65 : Refiner bearings Locating bearingFloating bearing 71...
Ngày tải lên: 11/08/2014, 05:22
The Design of Rolling Bearing Mountings Part 2 docx
... pres- sure in the rolling contact area of the bearing is rela- tively low (p 0 ≤ 2,000 N/mm 2 ), and the bearings are failsafe. Consequently, the service life of the bearings is dictated by the grease ... arranged. Bearing selection The axial load of 130 kN is made up of the weight of the rotor and the two variable top and bottom fan im- pellers as well as...
Ngày tải lên: 11/08/2014, 05:22
The Design of Rolling Bearing Mountings Part 3 docx
... of js5 .The bearing seats for the outer rings are machined to G6. The spring preload remains effective in all oper- ating conditions as the expansion of the rotating parts due to the effects of ... accuracy of the workpiece mainly depend on the axial rigidity of the spindle headstock and of the rotary table. Therefore, the rigidity of the thrust bear- in...
Ngày tải lên: 11/08/2014, 05:22
The Design of Rolling Bearing Mountings Part 4 pdf
... shaft Engine-end bearing: The roller and cage assembly runs directly on the out- put shaft and in the bore of the input shaft. The cage is guided by the rolling elements. The logarithmic profile of the rollers ... Depending on the direction of rotation of the worm shaft, either one or the other bearing accommodates the axial load. A cylindrical roller be...
Ngày tải lên: 11/08/2014, 05:22
The Design of Rolling Bearing Mountings Part 5 docx
... truck The Design of Rolling Bearing Mountings PDF 4/8: Rail vehicles Shipbuilding Rolling Bearings FAG OEM und Handel AG Publ. No. WL 00 200/5 EA The Design of Rolling Bearing Mountings Design ... for the oil for the pinion shaft particularly for the bearing on the flange side. Attention should be paid to the oil flow di- rection which is always from t...
Ngày tải lên: 11/08/2014, 05:22
The Design of Rolling Bearing Mountings Part 9 pdf
... bearings FAG 23 264 K.MB are mounted. The one-piece plummer block housings FAG BND3 264 K are made of cast steel GS-45. One of the plummer blocks acts as the locating bearing, the other one as the ... deformations of the head frame. Machining tolerances One bearing acts as the locating bearing, the other one as the floating bearing. Both bearings have a tapered b...
Ngày tải lên: 11/08/2014, 05:22
The Design of Rolling Bearing Mountings Part 10 pps
... both ends of the sprocket 88: Bottom sprocket of a bucket chain dredger The Design of Rolling Bearing Mountings PDF 6/ 8: Construction machinery Raw material processing Steel mill and rolling mill ... dowel screws. The drive-end bearing is mounted with two locating rings and acts as the locating bearing; the bearing at the opposite end is the floating bea...
Ngày tải lên: 11/08/2014, 05:22