Volume 20 - Materials Selection and Design Part 13 potx

... strength, MPa A 2 5-7 25 No 0.0105 -0 .0007 -0 .0098 Phase 1 -1 00 100 B 725 Yes -0 .0025 0.0017 0.0008 Phase 2 100 100 C 72 5-8 50 No 0.0026 -0 .0017 -0 .0009 Phase 2 -5 0 50 D 85 0-3 00 No -0 .0116 0.0017 ... electrode and flux deposited per hour 7.1 kg (15.6 lb) Weight of electrode and flux deposited per foot of weld: Original design (sing...

Ngày tải lên: 10/08/2014, 13:20

... the design process and these design tools. Thus, Volume 20 of ASM Handbook is aimed at two important groups: materials professionals and design professionals. As a handbook on materials selection ... 9). If a part is necessary and a standard part can be used, then it is usually more economical to specify the standard part instead of designing and manufacturi...

Ngày tải lên: 10/08/2014, 13:20

... alloys Alloy C-276 Ni-15.5Cr-16Mo-5.5Fe-3.75W-1.25Co + V 785 114 372 54 62 209 HB Alloy 625 Ni-21.5Cr-9Mo-3.65Nb + Ta-2.5Fe 930 135 517 75 42.5 190 HB Nickel-chromium-iron-molybdenum-copper alloys ... ZA-8 Zn-8Al-1Cu-0.025 Mg 374 54 8 103 Z35630 ZA-12 Zn-11Al-1Cu-0.025Mg 404 58 5 100 Z35840 ZA-27 Zn-27Al-2Cu-0.015Mg 426 62 2 119 Wrought alloys (hot-rolled condition) Z21 220 ....

Ngày tải lên: 10/08/2014, 13:20

... 2. 0- 2.5 24 1- 276 3 5- 40 1. 5-2 .5 13 80 0- 1065 15 -2 0 8 3-1 10 1 2- 16 13 8- 207 2 0- 30 17. 2- 20. 7 2. 5- 3.0 207 - 241 3 0- 35 1. 0-1 .5 25 1 96 0- 133 5 1 8-2 5 10 3- 138 1 5- 20 17 2- 241 ... (2 3-2 50 °C), 10 -4 in./in./°C <6 < 3 0-6 5 0. 6-1 .2 5 5-8 3 8-1 2 6 9-1 03 1...

Ngày tải lên: 10/08/2014, 13:20

... for the part thickness must be considered. The entire process is summarized in Fig. 13. Fig. 13 Design- based material -selection process Example 1: Materials Selection for Plate Design. coworkers. ... mold-cooling program allows designers and molders to evaluate materials and process parameters in a rapid, convenient, and cost-efficient manner. Plastic parts are us...

Ngày tải lên: 10/08/2014, 13:20

... 4.35 2.71 -1 3.08 9 96.33 102.00 4.56 2.00 -8 .77 10 105.94 102.39 4.49 2.39 -1 0.28 11 97.91 101.98 4.47 1.98 -1 0.65 12 98.41 101.69 4.39 1.69 -1 2 .20 13 92.55 100.98 4.87 0.98 -2 .59 14 ... 99.40 1.41 -0 .60 -7 1.81 3 100.47 99.75 1.26 -0 .25 -7 4.86 4 106.08 101.34 2.95 1.34 -4 1.05 5 111.21 103.31 4.75 3.31 -5 .05 6 98.10 102.44 4...

Ngày tải lên: 10/08/2014, 13:20

... in CAE-based design optimization. Computer-aided-engineering- based design optimization does in fact turn CAE analysis tools into CAE design tools by replacing traditional trial -and- error design ... block-structured grids. On the other hand, unstructured-mesh CFD codes generally demand higher computational resources. Additional memory is needed to store cell-to-cell and vertex-...

Ngày tải lên: 10/08/2014, 13:20

... Selection, Granta Design, 1996 3. CMS Software and Handbooks, Granta Design, 1995 4. American Institute of Physics Handbook, 3rd ed., McGraw-Hill, 1972 5. Metals Handbook, 9th ed., and ASM Handbook, ... which follows in this Section of the Handbook) for materials selection in the minimum-weight design of ties, columns, beams, and plates, and for yield-limited design of...

Ngày tải lên: 10/08/2014, 13:20

... understanding of structure/property relationships resulted, and the design of materials evolves in partnership with design with materials. Structure and Structure Analysis. Materials science and ... Eng. News-Rec., Vol 120 (No. 18), 5 May 1938, p 65 4-6 55 20. O. Bondy, Brittle Steel a Feature of Belgian Bridge Failure, Eng. News-Rec., Vol 121 (No. 7), 18 August 19...

Ngày tải lên: 10/08/2014, 13:20

... Corrosion-Resistant Materials Handbook, 4th ed., Noyes, 1985 • DECHEMA Corrosion Handbook: Corrosive Agents and Their Interaction with Materials, D. Behrens (Vol 1-9 ) and G. Kreysa and R. Eckermann ... Butterworths, 1969, p 11 5-1 37 19. J.L. Walter and H.E. Cline, Grain Boundary Sliding, Migration, and Deformation in High-Purit y Aluminum, Trans. AIME, Vol 242, 196...

Ngày tải lên: 10/08/2014, 13:20