Volume 20 - Materials Selection and Design Part 12 pdf

... Nordquist, Die Designing and Estimating, 4th ed., Huebner Publishing, 1955 12. E. Oberg, F.D. Jones, and H.L. Horton, Machinery's Handbook, 22nd ed., Industrial Press, 1987, p 118 8- 120 5 13. ... the initial design of the casting is the design of gates and risers. This consists of proper orientation of the part and the determination of the parting plane and the...

Ngày tải lên: 10/08/2014, 13:20

... the design process and these design tools. Thus, Volume 20 of ASM Handbook is aimed at two important groups: materials professionals and design professionals. As a handbook on materials selection ... 9). If a part is necessary and a standard part can be used, then it is usually more economical to specify the standard part instead of designing and manufacturi...

Ngày tải lên: 10/08/2014, 13:20

... Telecommunications Industries Association. 200 1 Pennsylvania Ave., N.W., Washington, D.C. 200 0 6-4 912 (202 ) 45 7-4 912 Standards Information Services. Copies of standards and information about documents ... 4.35 2.71 -1 3.08 9 96.33 102.00 4.56 2.00 -8 .77 10 105.94 102.39 4.49 2.39 -1 0.28 11 97.91 101.98 4.47 1.98 -1 0.65 12 98.41 101.69 4.39 1.69...

Ngày tải lên: 10/08/2014, 13:20

... in CAE-based design optimization. Computer-aided-engineering- based design optimization does in fact turn CAE analysis tools into CAE design tools by replacing traditional trial -and- error design ... block-structured grids. On the other hand, unstructured-mesh CFD codes generally demand higher computational resources. Additional memory is needed to store cell-to-cell and vertex-...

Ngày tải lên: 10/08/2014, 13:20

... Selection, Granta Design, 1996 3. CMS Software and Handbooks, Granta Design, 1995 4. American Institute of Physics Handbook, 3rd ed., McGraw-Hill, 1972 5. Metals Handbook, 9th ed., and ASM Handbook, ... which follows in this Section of the Handbook) for materials selection in the minimum-weight design of ties, columns, beams, and plates, and for yield-limited design of...

Ngày tải lên: 10/08/2014, 13:20

... Eng. News-Rec., Vol 120 (No. 18), 5 May 1938, p 65 4-6 55 20. O. Bondy, Brittle Steel a Feature of Belgian Bridge Failure, Eng. News-Rec., Vol 121 (No. 7), 18 August 1938, p 204 -2 06 21. ... understanding of structure/property relationships resulted, and the design of materials evolves in partnership with design with materials. Structure and Structure Analysis....

Ngày tải lên: 10/08/2014, 13:20

... ZA-8 Zn-8Al-1Cu-0.025 Mg 374 54 8 103 Z35630 ZA -1 2 Zn-11Al-1Cu-0.025Mg 404 58 5 100 Z35840 ZA-27 Zn-27Al-2Cu-0.015Mg 426 62 2 119 Wrought alloys (hot-rolled condition) Z21 220 . . . Zn-0.06Pb-0.06Cd ... Ni-21Cr-39.5Fe-0.4Ti-0.4Al 600 87 295 43 44 138 HB Alloy 617 Ni-22Cr-3Fe-12Co-9Mo-1Al 755 110 350 51 58 173 HB Alloy 690 Ni-29Cr-9Fe 725 105 348 50 41 88 HRB Alloy 751 Ni-15...

Ngày tải lên: 10/08/2014, 13:20

... 2. 0- 2.5 24 1- 276 3 5- 40 1. 5-2 .5 13 80 0- 1065 15 -2 0 8 3-1 10 1 2- 16 13 8- 207 2 0- 30 17. 2- 20. 7 2. 5- 3.0 207 - 241 3 0- 35 1. 0-1 .5 25 1 96 0- 1335 1 8-2 5 10 3- 138 1 5- 20 17 2- 241 ... (2 3-2 50 °C), 10 -4 in./in./°C <6 < 3 0-6 5 0. 6-1 .2 5 5-8 3 8-1 2 6 9-1 03 1 0-...

Ngày tải lên: 10/08/2014, 13:20

... Corrosion-Resistant Materials Handbook, 4th ed., Noyes, 1985 • DECHEMA Corrosion Handbook: Corrosive Agents and Their Interaction with Materials, D. Behrens (Vol 1-9 ) and G. Kreysa and R. Eckermann ... applies to stress- corrosion cracking (SCC), strain-induced cracking (SIC), and corrosion fatigue (CF). Fig. 43 Predicted and observed crack-propagation rate/crack-tip st...

Ngày tải lên: 10/08/2014, 13:20

... mold-cooling program allows designers and molders to evaluate materials and process parameters in a rapid, convenient, and cost-efficient manner. Plastic parts are usually thin, and thus a one-dimensional, ... Design- Based Material Selection Design- based material selection (Ref 12, 13) involves meeting the part performance requirements with a minimum system cost while...

Ngày tải lên: 10/08/2014, 13:20