Dimension TM 3100 Manual Version 4.43B phần 9 potx

... . . . 1- 7 1. 4.4 Dimension 310 0 Controller . . . . . . . . . . . 1- 8 1. 5 Dimension 310 0 SPM Overview . . . . . .1- 10 1. 5 .1 Dimension 310 0 Microscope Electronics Box 1- 10 1. 5.2 Optics ... Rev. B Dimension 310 0 Manual TOC -1 Dimension 310 0 Manual Table of Contents List of Figures LOF -1 Chapter 1 System Overview 1- 1 1. 1 O...

Ngày tải lên: 08/08/2014, 13:20

... Safety 2- 2 Dimension 3100 Manual Rev. B 2. 2 Safety Requirements Figure 2. 2a Safety Symbols Key Symbol Definition This symbol identifies

Ngày tải lên: 08/08/2014, 13:20

... Installation 4-4 Dimension 31 00 Manual Rev. B 4 .3 Uncrating the System 4 .3. 1 Uncrate the Dimension 31 00 SPM System 1. Using scissors, cut and remove the plastic shipping band encircling the Dimension 31 00 ... boxes: ã Dimension 31 00 Microscope ã NanoScope IIIa Controller (if applicable) ã Dimension 31 00 Controller ã Computer and Keyboard ã Dimension Micr...

Ngày tải lên: 08/08/2014, 13:20

... Cantilever Preparation 6-8 Dimension 3100 Manual Rev. B Tip Shape of Etched Silicon Probes continued Measurements of line pitch are

Ngày tải lên: 08/08/2014, 13:20

... Contact AFM 8-16 Dimension 3100 Manual Rev. B This page is intentionally blank.

Ngày tải lên: 08/08/2014, 13:20

... TappingMode AFM in Fluids 11-10 Dimension 3100 Manual Rev. B Manual Cantilever Tuning continued Figure 11.4c Cantilever Tune Control Panels for

Ngày tải lên: 08/08/2014, 13:20

... Force Imaging 13-22 Dimension 3100 Manual Rev. B Obtaining a Good Force Curve continued Figure 13.5d Adjusted Force Curve

Ngày tải lên: 08/08/2014, 13:20

... Interleave Scanning 14-14 Dimension 3100 Manual Rev. B

Ngày tải lên: 08/08/2014, 13:20

... Electric Techniques 16-24 Dimension 3100 Manual Rev. B Phase Detection continued Note: For software versions 4.23 and lower set Interleave scan to Lift and switch ... Note: For software versions 4.23 and lower, there are no separate Analog 2 setting in the Interleave Controls panel. Set Analog 2 in the Feedback Controls panel to 0 volts. 9. In the Interleave ... scan height is s...

Ngày tải lên: 08/08/2014, 13:20

... Calibration 17-30 Dimension 3100 Manual Rev. B Measure Horizontally at 440 Scan Size continued 8. Multiply the quotient ... actual feature distances. The new sensitivity setting takes effect as soon as it is entered. 10. To save it to the computer’s hard disk, click on OK. This closes the Scanner Calibration panel. 17.7.3

Ngày tải lên: 08/08/2014, 13:20

... ParkzoneTransmitterswithtrainingjack("DX5eadaptor"required) • Art‐tech 10 0B(noadaptorrequired) • Art‐tech 10 0C("Art‐tech 10 0Cadaptor"required) • Walkera24 01, 26 01 (Using"MINI‐DINadaptor"suppliedwithtransmitter) • ... Walkera24 01, 26 01 (Using"MINI‐DINadaptor"suppliedwithtransmitter) • Walkera2402,2602("Walk...

Ngày tải lên: 12/08/2014, 22:21

... currently selected model ontheright. The model list This list displays all models that you  currently have installed. Models in the li st are sorted into their main model categories(Fixedwing,Helicopters,GlidersandOthe ... Belowthe model selectionlistyouwillfindanotherdrop‐downbox.Manymodelsin Phoenix featuremorethanone colour‐scheme,andwhenthisis...

Ngày tải lên: 12/08/2014, 22:21

... layout, and placesthemodelinthecentre,facingawayfromyou. ã F3CAreaEnablestheF3CArealayout,whichrecreatesthestandardF3Cflightlinewithtwo5mdis tan t flagsandplacesthe model inthecentre,facingawayfromyou. Buddies Buddiesareartificiallyintelligentcomputer‐controlledpilotswhoflywithyouonthefieldwheninsolo flight ... AftertakeoffThefailurewilloccurshortlyafteryourmodelle...

Ngày tải lên: 12/08/2014, 22:21

... mutebuttonwillturntheVariometertonevolume upanddownrespectively.  Flight Recorder Phoenix featuresapowerfulandfull‐featured flight recorderwhichletsyourecorda flight (orseriesofflights),and thensavetheseto disktosharewithother Phoenix ... a shorttime.The flight recordercanalsobeminimise dusingtheblueminimisebuttonontherecordertitle‐bar....

Ngày tải lên: 12/08/2014, 22:21

... that using threads to deal with blocking I/O differs in a fundamental way from using threads to speed up computation. When using threads for speed- up in Subsection 12.3.2, it made sense to use ... animation to be computed and displayed. In the respons e to the event, it is only necessary to update some state variables and to repaint the display to reflect the changes. A T...

Ngày tải lên: 13/08/2014, 18:20