Dimension TM 3100 Manual Version 4 43B phần 8 docx

... Interleave Scanning 14- 14 Dimension 3100 Manual Rev. B

Ngày tải lên: 08/08/2014, 13:20

... Installation 4- 4 Dimension 3100 Manual Rev. B 4. 3 Uncrating the System 4. 3.1 Uncrate the Dimension 3100 SPM System 1. Using scissors, cut and remove the plastic shipping band encircling the Dimension 3100 ... boxes: • Dimension 3100 Microscope • NanoScope IIIa Controller (if applicable) • Dimension 3100 Controller • Computer and Keyboard • Dimension Microscope H...

Ngày tải lên: 08/08/2014, 13:20

... TappingMode AFM in Fluids 11-10 Dimension 3100 Manual Rev. B Manual Cantilever Tuning continued Figure 11.4c Cantilever Tune Control Panels for Interleave Controls 9. ... the sample and other scanning conditions. Figure 11.4d Cantilever Tune Frequency Sweep Cantilever Response 0.50 V/div Center Frequency - 337 .87 23 KHz 0.05 KHz/div Setpoint Frequency Sweep

Ngày tải lên: 08/08/2014, 13:20

... 1-6 1 .4. 3 NanoScope IIIa Controller . . . . . . . . . . . 1-7 1 .4. 4 Dimension 3100 Controller . . . . . . . . . . . 1 -8 1.5 Dimension 3100 SPM Overview . . . . . .1-10 1.5.1 Dimension ... Rev. B Dimension 3100 Manual TOC-1 Dimension 3100 Manual Table of Contents List of Figures LOF-1 Chapter 1 System ... 1.3.1 Dimension 3100 SPM Feat...

Ngày tải lên: 08/08/2014, 13:20

... Safety 2-2 Dimension 3100 Manual Rev. B 2.2 Safety Requirements Figure 2.2a Safety Symbols Key Symbol Definition This

Ngày tải lên: 08/08/2014, 13:20

... Cantilever Preparation 6 -8 Dimension 3100 Manual Rev. B Tip Shape of Etched Silicon Probes continued Measurements of line pitch ... Profile 55° 70 - 80 ° 10° 1 µm - 2 µm Deep Trench Note: Any wall angle on the left wall that is > 55 deg. will be shown as 55 deg. in the image. Any wall angle on the right wall that is >70 -80 deg. ... the image. Any wall angle on the right w...

Ngày tải lên: 08/08/2014, 13:20

... Contact AFM 8- 16 Dimension 3100 Manual Rev. B This page is intentionally blank.

Ngày tải lên: 08/08/2014, 13:20

... Force Imaging 13-22 Dimension 3100 Manual Rev. B Obtaining a Good Force Curve continued Figure 13.5d Adjusted Force Curve ... effect of pushing the cantilever farther up before the Setpoint is reached. Tip Deflection 0 . 48 V/div Z Position - 10.00 V/div Set p oint Retracting Extending

Ngày tải lên: 08/08/2014, 13:20

... Electric Techniques 16- 24 Dimension 3100 Manual Rev. B Phase Detection continued Note: For software versions 4. 23 and lower set Interleave scan to Lift and switch ... to Enable in the Interleave Controls panel. 8. Set the Channel 2 Scan line to Interleave to display interleave data. Note: For software versions 4. 23 and lower, there are no separate Analog ... scan height is...

Ngày tải lên: 08/08/2014, 13:20

... Calibration 17-30 Dimension 3100 Manual Rev. B Measure Horizontally at 44 0 Scan Size continued 8. Multiply the quotient obtained above by the X fast sens ... hard disk, click on OK. This closes the Scanner Calibration panel. 17.7.3 Measure Vertically at 44 0V Scan Size 1. Return to the image of the calibration reference. 2. Clear the horizontal line ... and click the right mouse...

Ngày tải lên: 08/08/2014, 13:20