Dimension TM 3100 Manual Version 4 43B phần 5 doc

... Contact AFM 8-16 Dimension 3100 Manual Rev. B This page is intentionally blank.

Ngày tải lên: 08/08/2014, 13:20

... Installation 4- 4 Dimension 3100 Manual Rev. B 4. 3 Uncrating the System 4. 3.1 Uncrate the Dimension 3100 SPM System 1. Using scissors, cut and remove the plastic shipping band encircling the Dimension 3100 ... boxes: • Dimension 3100 Microscope • NanoScope IIIa Controller (if applicable) • Dimension 3100 Controller • Computer and Keyboard • Dimension Microscope H...

Ngày tải lên: 08/08/2014, 13:20

... TappingMode AFM in Fluids 11-10 Dimension 3100 Manual Rev. B Manual Cantilever Tuning continued Figure 11.4c Cantilever Tune Control Panels for Interleave Controls 9. ... sample and other scanning conditions. Figure 11.4d Cantilever Tune Frequency Sweep Cantilever Response 0 .50 V/div Center Frequency - 337.8723 KHz 0. 05 KHz/div Setpoint Frequency Sweep

Ngày tải lên: 08/08/2014, 13:20

... Interleave Scanning 14- 14 Dimension 3100 Manual Rev. B

Ngày tải lên: 08/08/2014, 13:20

... 1-6 1 .4. 3 NanoScope IIIa Controller . . . . . . . . . . . 1-7 1 .4. 4 Dimension 3100 Controller . . . . . . . . . . . 1-8 1 .5 Dimension 3100 SPM Overview . . . . . .1-10 1 .5. 1 Dimension ... 1.3.1 Dimension 3100 SPM Features . . . . . . . . 1-3 1 .4 Control Station Overview . . . . . . . . . . . . .1 -5 1 .4. 1 Input and Display Devices . . . . ....

Ngày tải lên: 08/08/2014, 13:20

... Safety 2-2 Dimension 3100 Manual Rev. B 2.2 Safety Requirements Figure 2.2a Safety Symbols Key Symbol Definition This

Ngày tải lên: 08/08/2014, 13:20

... the range of 5 10 nm (on a very good tip). S can Line Profile 55 ° 70 - 80° 10° 1 µm - 2 µm Deep Trench Note: Any wall angle on the left wall that is > 55 deg. will be shown as 55 deg. in the ... Cantilever Preparation 6-8 Dimension 3100 Manual Rev. B Tip Shape of Etched Silicon Probes continued Measurements of line pitch are

Ngày tải lên: 08/08/2014, 13:20

... Force Imaging 13-22 Dimension 3100 Manual Rev. B Obtaining a Good Force Curve continued Figure 13.5d Adjusted Force Curve for 90 µm Scanner 13 .5. 2 Helpful Suggestions To minimize ... situations. Suggestions on working in Force Calibration mode are included. False Engagement Figure 13.5e illustrates a force curve resulting from a falsely engaged tip. The photodiode receives light .....

Ngày tải lên: 08/08/2014, 13:20

... Electric Techniques 16- 24 Dimension 3100 Manual Rev. B Phase Detection continued Note: For software versions 4. 23 and lower set Interleave scan to Lift and switch ... Set the Channel 2 Scan line to Interleave to display interleave data. Note: For software versions 4. 23 and lower, there are no separate Analog 2 setting in the Interleave Controls panel. ... scan height is set...

Ngày tải lên: 08/08/2014, 13:20

... Calibration 17-30 Dimension 3100 Manual Rev. B Measure Horizontally at 44 0 Scan Size continued 8. Multiply the quotient obtained above by the ... hard disk, click on OK. This closes the Scanner Calibration panel. 17.7.3 Measure Vertically at 44 0V Scan Size 1. Return to the image of the calibration reference. 2. Clear the horizontal line ... and click the right mouse button, or c...

Ngày tải lên: 08/08/2014, 13:20