Dimension TM 3100 Manual Version 4 43B phần 4 pps
Dimension TM 3100 Manual Version 4.43B phần 1 pot
... 1-6
1 .4. 3 NanoScope IIIa Controller
. . . . . . . . . . . 1-7
1 .4. 4 Dimension 3100 Controller
. . . . . . . . . . . 1-8
1.5 Dimension 3100 SPM Overview
. . . . . .1-10
1.5.1 Dimension ...
Rev. B
Dimension 3100 Manual
TOC-1
Dimension 3100 Manual
Table of Contents
List of Figures
LOF-1
Chapter 1
System ...
1.3.1 Dimension 3100 SPM Featu...
Dimension TM 3100 Manual Version 4.43B phần 2 potx
... Safety
2-2 Dimension 3100 Manual Rev. B
2.2 Safety Requirements
Figure 2.2a Safety Symbols Key
Symbol Definition
This
Dimension TM 3100 Manual Version 4.43B phần 3 docx
... Installation
4- 4 Dimension 3100 Manual Rev. B
4. 3 Uncrating the System
4. 3.1 Uncrate the Dimension 3100 SPM System
1. Using scissors, cut and remove the plastic shipping band encircling
the Dimension 3100 ... boxes:
• Dimension 3100 Microscope
• NanoScope IIIa Controller (if applicable)
• Dimension 3100 Controller
• Computer and Keyboard
• Dimension Microscope H...
Dimension TM 3100 Manual Version 4.43B phần 4 pps
... Cantilever Preparation
6-8 Dimension 3100 Manual Rev. B
Tip Shape of Etched Silicon Probes continued
Measurements of line pitch are
Dimension TM 3100 Manual Version 4.43B phần 5 doc
... Contact AFM
8-16 Dimension 3100 Manual Rev. B
This page is intentionally blank.
Dimension TM 3100 Manual Version 4.43B phần 6 docx
... TappingMode AFM in Fluids
11-10 Dimension 3100 Manual Rev. B
Manual Cantilever Tuning continued
Figure 11.4c Cantilever Tune Control Panels for Interleave Controls
9. ... The desired operating amplitude depends on
the sample and other scanning conditions.
Figure 11.4d Cantilever Tune Frequency Sweep
Cantilever
Response
0.50 V/div
Center Frequency - 337.8723 KHz
Dimension TM 3100 Manual Version 4.43B phần 7 ppsx
... Force Imaging
13-22 Dimension 3100 Manual Rev. B
Obtaining a Good Force Curve continued
Figure 13.5d Adjusted Force Curve ...
effect of pushing the cantilever farther up before the Setpoint is reached.
Tip
Deflection
0 .48 V/div
Z Position - 10.00 V/div
Set
p
oint
Retracting
Extending
Dimension TM 3100 Manual Version 4.43B phần 8 docx
... Interleave Scanning
14- 14 Dimension 3100 Manual Rev. B
Dimension TM 3100 Manual Version 4.43B phần 9 potx
... Electric Techniques
16- 24 Dimension 3100 Manual Rev. B
Phase Detection continued
Note: For software versions 4. 23 and lower set
Interleave scan to Lift and switch ... Set the Channel 2 Scan line to Interleave to display interleave
data.
Note: For software versions 4. 23 and lower,
there are no separate Analog 2 setting in the
Interleave Controls panel. ... scan
height is set...
Dimension TM 3100 Manual Version 4.43B phần 10 pptx
... Calibration
17-30 Dimension 3100 Manual Rev. B
Measure Horizontally at 44 0 Scan Size continued
8. Multiply the quotient obtained above by the ... hard disk, click on
OK. This closes the
Scanner Calibration panel.
17.7.3 Measure Vertically at 44 0V Scan Size
1. Return to the image of the calibration reference.
2. Clear the horizontal line ... and click the right mouse
button, or c...
Từ khóa: