Dimension TM 3100 Manual Version 4 43B phần 3 docx

... Installation 4- 4 Dimension 31 00 Manual Rev. B 4. 3 Uncrating the System 4. 3. 1 Uncrate the Dimension 31 00 SPM System 1. Using scissors, cut and remove the plastic shipping band encircling the Dimension 31 00 ... boxes: • Dimension 31 00 Microscope • NanoScope IIIa Controller (if applicable) • Dimension 31 00 Controller • Computer and Keyboard • Dimension...

Ngày tải lên: 08/08/2014, 13:20

... TappingMode AFM in Fluids 11-10 Dimension 31 00 Manual Rev. B Manual Cantilever Tuning continued Figure 11.4c Cantilever Tune Control Panels for Interleave Controls 9. ... the sample and other scanning conditions. Figure 11.4d Cantilever Tune Frequency Sweep Cantilever Response 0.50 V/div Center Frequency - 33 7.87 23 KHz 0.05 KHz/div Setpoint Frequency Sweep

Ngày tải lên: 08/08/2014, 13:20

... Interleave Scanning 14- 14 Dimension 31 00 Manual Rev. B

Ngày tải lên: 08/08/2014, 13:20

... 1 .3 System Overview . . . . . . . . . . . . . . . . . . .1 -3 1 .3. 1 Dimension 31 00 SPM Features . . . . . . . . 1 -3 1 .4 Control Station Overview . . . . . . . . . . . . .1-5 1 .4. 1 ... Rev. B Dimension 31 00 Manual TOC-1 Dimension 31 00 Manual Table of Contents List of Figures LOF-1 Chapter 1 System ... . . . . . . 1-5 1 .4. 2 Computer...

Ngày tải lên: 08/08/2014, 13:20

... Safety 2-2 Dimension 31 00 Manual Rev. B 2.2 Safety Requirements Figure 2.2a Safety Symbols Key Symbol Definition This

Ngày tải lên: 08/08/2014, 13:20

... Cantilever Preparation 6-8 Dimension 31 00 Manual Rev. B Tip Shape of Etched Silicon Probes continued Measurements of line pitch are

Ngày tải lên: 08/08/2014, 13:20

... Contact AFM 8-16 Dimension 31 00 Manual Rev. B This page is intentionally blank.

Ngày tải lên: 08/08/2014, 13:20

... Force Imaging 13- 22 Dimension 31 00 Manual Rev. B Obtaining a Good Force Curve continued Figure 13. 5d Adjusted Force Curve for 90 µm Scanner 13. 5.2 Helpful Suggestions To minimize ... situations. Suggestions on working in Force Calibration mode are included. False Engagement Figure 13. 5e illustrates a force curve resulting from a falsely engaged tip. The photodiode receives li...

Ngày tải lên: 08/08/2014, 13:20

... Electric Techniques 16- 24 Dimension 31 00 Manual Rev. B Phase Detection continued Note: For software versions 4. 23 and lower set Interleave scan to Lift and switch ... Set the Channel 2 Scan line to Interleave to display interleave data. Note: For software versions 4. 23 and lower, there are no separate Analog 2 setting in the Interleave Controls panel. Set ... scan heigh...

Ngày tải lên: 08/08/2014, 13:20

... Calibration 17 -30 Dimension 31 00 Manual Rev. B Measure Horizontally at 44 0 Scan Size continued 8. Multiply the quotient obtained above by ... panel. 17.7 .3 Measure Vertically at 44 0V Scan Size 1. Return to the image of the calibration reference. 2. Clear the horizontal line drawn earlier and click the right mouse button, or click on CLEAR. 3. ... and click the right mouse b...

Ngày tải lên: 08/08/2014, 13:20