Dimension TM 3100 Manual Version 4 43B phần 2 potx

... Safety 2- 2 Dimension 3100 Manual Rev. B 2. 2 Safety Requirements Figure 2. 2a Safety Symbols Key Symbol Definition This symbol identifies

Ngày tải lên: 08/08/2014, 13:20

... Electric Techniques 16- 24 Dimension 3100 Manual Rev. B Phase Detection continued Note: For software versions 4. 23 and lower set Interleave scan to Lift and switch ... Channel 2 Scan line to Interleave to display interleave data. Note: For software versions 4. 23 and lower, there are no separate Analog 2 setting in the Interleave Controls panel. Set Analog 2 in ... Ana...

Ngày tải lên: 08/08/2014, 13:20

... 1-7 1 .4. 4 Dimension 3100 Controller . . . . . . . . . . . 1-8 1.5 Dimension 3100 SPM Overview . . . . . .1-10 1.5.1 Dimension 3100 Microscope Electronics Box 1-10 1.5 .2 Optics ... Rev. B Dimension 3100 Manual TOC-1 Dimension 3100 Manual Table of Contents List of Figures LOF-1 Chapter 1 System ... .1-1 1 .2 How to Reach Digital Instrume...

Ngày tải lên: 08/08/2014, 13:20

... Installation 4- 4 Dimension 3100 Manual Rev. B 4. 3 Uncrating the System 4. 3.1 Uncrate the Dimension 3100 SPM System 1. Using scissors, cut and remove the plastic shipping band encircling the Dimension 3100 ... crate. 2. Lift the cardboard shipping box off of the Dimension 3100 microscope. 3. Unscrew the 2 shipping bolts holding the shipping brackets in place at ei...

Ngày tải lên: 08/08/2014, 13:20

... Cantilever Preparation 6-8 Dimension 3100 Manual Rev. B Tip Shape of Etched Silicon Probes continued Measurements of line pitch are ... simplification of the measurement artifacts (See Figure 6.2e). Figure 6.2e Common Silicon Probe Profile (Resultant Scan Artifact) Figure 6.2e depicts the resultant effect of the angled back ridge ... topography dependent. In addition to microscopic sca...

Ngày tải lên: 08/08/2014, 13:20

... Contact AFM 8-16 Dimension 3100 Manual Rev. B This page is intentionally blank.

Ngày tải lên: 08/08/2014, 13:20

... TappingMode AFM in Fluids 11-10 Dimension 3100 Manual Rev. B Manual Cantilever Tuning continued Figure 11.4c Cantilever Tune Control Panels for Interleave Controls 9. ... the sample and other scanning conditions. Figure 11.4d Cantilever Tune Frequency Sweep Cantilever Response 0.50 V/div Center Frequency - 337.8 723 KHz 0.05 KHz/div Setpoint Frequency Sweep

Ngày tải lên: 08/08/2014, 13:20

... Force Imaging 13 -22 Dimension 3100 Manual Rev. B Obtaining a Good Force Curve continued Figure 13.5d Adjusted Force Curve for 90 µm Scanner 13.5 .2 Helpful Suggestions To minimize ... effect of pushing the cantilever farther up before the Setpoint is reached. Tip Deflection 0 .48 V/div Z Position - 10.00 V/div Set p oint Retracting Extending

Ngày tải lên: 08/08/2014, 13:20

... Interleave Scanning 14- 14 Dimension 3100 Manual Rev. B

Ngày tải lên: 08/08/2014, 13:20

... Calibration 17-30 Dimension 3100 Manual Rev. B Measure Horizontally at 44 0 Scan Size continued 8. Multiply the quotient obtained above by the ... the Scanner Calibration panel. 17.7.3 Measure Vertically at 44 0V Scan Size 1. Return to the image of the calibration reference. 2. Clear the horizontal line drawn earlier and click the right ... and click the right mouse button, or cli...

Ngày tải lên: 08/08/2014, 13:20