... . . . 1- 7 1 .4. 4 Dimension 310 0 Controller . . . . . . . . . . . 1- 8 1. 5 Dimension 310 0 SPM Overview . . . . . .1- 10 1. 5 .1 Dimension 310 0 Microscope Electronics Box 1- 10 1. 5.2 Optics ... Rev. B Dimension 310 0 Manual TOC -1 Dimension 310 0 Manual Table of Contents List of Figures LOF -1 Chapter 1 System Overview 1- 1 1. 1...
Ngày tải lên: 08/08/2014, 13:20
... Safety 2-2 Dimension 310 0 Manual Rev. B 2.2 Safety Requirements Figure 2.2a Safety Symbols Key Symbol Definition This ... Extremfällen zu Verletzungen führen können. This symbol identifies conditions or practices that involve potential electric shock hazard. Ce symbole indique des conditions d'emploi ou des actions
Ngày tải lên: 08/08/2014, 13:20
Dimension TM 3100 Manual Version 4.43B phần 9 potx
... Electric Techniques 16 - 24 Dimension 310 0 Manual Rev. B Phase Detection continued Note: For software versions 4. 23 and lower set Interleave scan to Lift and switch ... during the LiftMode scan. Increase the Lift scan height until the Interleave scan image changes indicating that the tip is oscillating above the surface and not continuously tapping. 11 . Adjust ... Set the Ch...
Ngày tải lên: 08/08/2014, 13:20
Dimension TM 3100 Manual Version 4.43B phần 3 docx
... Installation 4- 4 Dimension 310 0 Manual Rev. B 4. 3 Uncrating the System 4. 3 .1 Uncrate the Dimension 310 0 SPM System 1. Using scissors, cut and remove the plastic shipping band encircling the Dimension 310 0 ... boxes: • Dimension 310 0 Microscope • NanoScope IIIa Controller (if applicable) • Dimension 310 0 Controller • Computer and Keyboard • Dimension Micr...
Ngày tải lên: 08/08/2014, 13:20
Dimension TM 3100 Manual Version 4.43B phần 4 pps
... Cantilever Preparation 6-8 Dimension 310 0 Manual Rev. B Tip Shape of Etched Silicon Probes continued Measurements of line pitch are ... radius of curvature of a silicon tip can be in the range of 5 10 nm (on a very good tip). S can Line Profile 55° 70 - 80° 10 ° 1 µm - 2 µm Deep Trench Note: Any wall angle on the left wall that ... (nominal 10 0 nm) step height measurements is...
Ngày tải lên: 08/08/2014, 13:20
Dimension TM 3100 Manual Version 4.43B phần 5 doc
... Contact AFM 8 -16 Dimension 310 0 Manual Rev. B This page is intentionally blank.
Ngày tải lên: 08/08/2014, 13:20
Dimension TM 3100 Manual Version 4.43B phần 6 docx
... TappingMode AFM in Fluids 11 -10 Dimension 310 0 Manual Rev. B Manual Cantilever Tuning continued Figure 11 .4c Cantilever Tune Control Panels for Interleave Controls 9. ... frequency. The desired operating amplitude depends on the sample and other scanning conditions. Figure 11 .4d Cantilever Tune Frequency Sweep Cantilever Response 0.50 V/div Center Frequency - 337.8723
Ngày tải lên: 08/08/2014, 13:20
Dimension TM 3100 Manual Version 4.43B phần 7 ppsx
... Force Imaging 13 -22 Dimension 310 0 Manual Rev. B Obtaining a Good Force Curve continued Figure 13 .5d Adjusted Force Curve for 90 µm Scanner 13 .5.2 Helpful Suggestions To minimize ... pushing the cantilever farther up before the Setpoint is reached. Tip Deflection 0 .48 V/div Z Position - 10 .00 V/div Set p oint Retracting Extending ... situations. Suggestions on working in...
Ngày tải lên: 08/08/2014, 13:20
Dimension TM 3100 Manual Version 4.43B phần 8 docx
... Interleave Scanning 14 - 14 Dimension 310 0 Manual Rev. B
Ngày tải lên: 08/08/2014, 13:20
Dimension TM 3100 Manual Version 4.43B phần 10 pptx
... Calibration 17 -30 Dimension 310 0 Manual Rev. B Measure Horizontally at 44 0 Scan Size continued 8. Multiply the quotient obtained above by ... soon as it is entered. 10 . To save it to the computer’s hard disk, click on OK. This closes the Scanner Calibration panel. 17 .7.3 Measure Vertically at 44 0V Scan Size 1. Return to the image ... to the next step. If the displayed d...
Ngày tải lên: 08/08/2014, 13:20