Autodesk Revit Architecture 2011 No Experience Required - part 77 ppt

... Soffit Wall. 9. Change Wall 2 to Interior - 6 1/8 ″ Partition (2-Hr). 10. Change Height to 5’–6”. 11. Insert a wall below the Interior - 6 1/8 ″ Partition (2-Hr) wall. 12. Change the third wall ... Figure 16.21. So, we can now make modifications to a simple wall in any direction. We have experience adding sweeps to the wall’s composition, and we can add sweeps free- hand when we n...

Ngày tải lên: 07/07/2014, 08:20

... The Revit Architecture Interface 25 TIP When you change the view control in a view, it is not a temporary display. You are telling Revit how you want to plot this ... (Building Elevation) cat- egory. Double-click on South. 8. Also in the Project Browser, notice there is a 3D Views category. Expand the 3D Views category, and double-click on the {3D} choice. ... in Figure 1.40. Let’...

Ngày tải lên: 07/07/2014, 07:20

... offset the alignment line down. Your plan should now look like Figure 2.5. TIP Notice you did not actually use the Offset command. Revit Architecture has the offset function built into most ... created in Chapter 1. If you did not complete that chapter, open the file called NER-01.rvt, which you can download from the book’s website at www.sybex.com/go /revit2 011ner. (You can also u...

Ngày tải lên: 07/07/2014, 07:20

... bubble. NOTE Notice that when you are adjusting the levels in the section the 2D icon appears. This means that any adjustments made here will not affect any other views. In a sectional view, Revit ... section into the cor- rect direction. WARNING We may be jumping ahead here, but here’s a word of caution: if you cut a section in Revit Architecture, then place detail compo- nents...

Ngày tải lên: 07/07/2014, 07:20

... Luckily in Revit Architecture, callouts are not only easy to add to your model but they directly link to the view they refer to as well. This is crucial for project coordination. Another nice ... scale. Yes, your call- out can be at a different scale. To follow along, open your model, or go to www.sybex.com/go /revit2 011ner and browse to Chapter 3. Open the file called NER-09.rvt. If y...

Ngày tải lên: 07/07/2014, 08:20

... to follow along. If you have not com- pleted the previous chapter procedures, open the file caller NER-11.rvt found at the book’s website, www.sybex.com/go /revit2 011ner. Go to the Chapter 4 ... with the edit commands. NOTE Like the previous chapters, it is important that you are com- fortable with this chapter. If you are not comfortable with the first few chap- ters, I recommend skimmin...

Ngày tải lên: 07/07/2014, 08:20

... dimensions are the go-to dimension, they are put on the bench for most of the game in Revit. The best use for a linear dimen- sion is when you want to put a straight dimension across nonlinear (angled) ... corridor area. 2. On the Annotate tab, select the Linear Dimension button. Notice that you cannot select the entire wall. That option has been taken away. Instead, Revit requires you...

Ngày tải lên: 07/07/2014, 08:20

... have no idea where the view is extended to. Is it to the end of the building? You just don’t know. If you pick the elevation arrow (the part of the elevation marker), you can then grip- edit ... Properties panel select Exterior - Brick And CMU On MTL. Stud (No Parapet), as shown in Figure 7.38. FIGURE 7.38 Changing the walls to Exterior - Brick And CMU On MTL. Stud (No...

Ngày tải lên: 07/07/2014, 08:20

... canopy roof. The walls are now joined to the roof, as shown in Figure 7.58. FIGURE 7.58 The walls are now attached to the roof. All of the conventional roofing systems have been added. It is now ... reference planes and creating a separate roof for this canopy. Try to make this a habit! 1. On the Draw panel, click the Start-End-Radius Arc button, as shown in Figure 7.53. 2. Draw an arc ......

Ngày tải lên: 07/07/2014, 08:20

... Finish Edit Mode. You now have a plan region. Although it may not seem as though you did any- thing in the plan, when you place a ceiling at 14 ′–6″, you will be able to see it. NOTE The dotted ... annoying (especially if you start col- lecting several plan regions), I recommend that you keep them turned on. It is helpful to know where a plan region is in the model, and it is more impor- t...

Ngày tải lên: 07/07/2014, 08:20