Autodesk Revit Architecture 2011 No Experience Required - part 57 ppt

... learn that Revit knows the type of view you hap- pen to be in. Some commands are available in one view, but they may not be in the next. Keep this in mind as you venture through Revit and become ... legend Chapter 11 • Schedules and Tags 538 Using the Revit Symbols To use the Revit- provided symbols, you will create a new legend view, and you will use the Annotate tab to insert the t...

Ngày tải lên: 07/07/2014, 08:20

... The Revit Architecture Interface 25 TIP When you change the view control in a view, it is not a temporary display. You are telling Revit how you want to plot this ... (Building Elevation) cat- egory. Double-click on South. 8. Also in the Project Browser, notice there is a 3D Views category. Expand the 3D Views category, and double-click on the {3D} choice. ... in Figure 1.40. Let’...

Ngày tải lên: 07/07/2014, 07:20

... offset the alignment line down. Your plan should now look like Figure 2.5. TIP Notice you did not actually use the Offset command. Revit Architecture has the offset function built into most ... created in Chapter 1. If you did not complete that chapter, open the file called NER-01.rvt, which you can download from the book’s website at www.sybex.com/go /revit2 011ner. (You can also u...

Ngày tải lên: 07/07/2014, 07:20

... bubble. NOTE Notice that when you are adjusting the levels in the section the 2D icon appears. This means that any adjustments made here will not affect any other views. In a sectional view, Revit ... section into the cor- rect direction. WARNING We may be jumping ahead here, but here’s a word of caution: if you cut a section in Revit Architecture, then place detail compo- nents...

Ngày tải lên: 07/07/2014, 07:20

... Luckily in Revit Architecture, callouts are not only easy to add to your model but they directly link to the view they refer to as well. This is crucial for project coordination. Another nice ... scale. Yes, your call- out can be at a different scale. To follow along, open your model, or go to www.sybex.com/go /revit2 011ner and browse to Chapter 3. Open the file called NER-09.rvt. If y...

Ngày tải lên: 07/07/2014, 08:20

... to follow along. If you have not com- pleted the previous chapter procedures, open the file caller NER-11.rvt found at the book’s website, www.sybex.com/go /revit2 011ner. Go to the Chapter 4 ... with the edit commands. NOTE Like the previous chapters, it is important that you are com- fortable with this chapter. If you are not comfortable with the first few chap- ters, I recommend skimmin...

Ngày tải lên: 07/07/2014, 08:20

... dimensions are the go-to dimension, they are put on the bench for most of the game in Revit. The best use for a linear dimen- sion is when you want to put a straight dimension across nonlinear (angled) ... corridor area. 2. On the Annotate tab, select the Linear Dimension button. Notice that you cannot select the entire wall. That option has been taken away. Instead, Revit requires you...

Ngày tải lên: 07/07/2014, 08:20

... have no idea where the view is extended to. Is it to the end of the building? You just don’t know. If you pick the elevation arrow (the part of the elevation marker), you can then grip- edit ... Properties panel select Exterior - Brick And CMU On MTL. Stud (No Parapet), as shown in Figure 7.38. FIGURE 7.38 Changing the walls to Exterior - Brick And CMU On MTL. Stud (No...

Ngày tải lên: 07/07/2014, 08:20

... the two together 4. Your roof should look like Figure 7 .57. Select the three walls below the roof. FIGURE 7 .57 The now completed canopy Picking the wall is easier said than done, mostly because ... canopy roof. The walls are now joined to the roof, as shown in Figure 7.58. FIGURE 7.58 The walls are now attached to the roof. All of the conventional roofing systems have been added. It is...

Ngày tải lên: 07/07/2014, 08:20

... Finish Edit Mode. You now have a plan region. Although it may not seem as though you did any- thing in the plan, when you place a ceiling at 14 ′–6″, you will be able to see it. NOTE The dotted ... annoying (especially if you start col- lecting several plan regions), I recommend that you keep them turned on. It is helpful to know where a plan region is in the model, and it is more impor- t...

Ngày tải lên: 07/07/2014, 08:20