Autodesk Revit Architecture 2011 No Experience Required - part 15 ppt
Autodesk Revit Architecture 2011 No Experience Required - part 15 ppt
... bubble.
NOTE
Notice that when you are adjusting the levels in the section the
2D icon appears. This means that any adjustments made here will not affect any
other views. In a sectional view, Revit ... section into the cor-
rect direction.
WARNING
We may be jumping ahead here, but here’s a word of
caution: if you cut a section in Revit Architecture, then place detail compo-
nents...
Autodesk Revit Architecture 2011 No Experience Required - part 6 ppt
... The Revit Architecture Interface
25
TIP
When you change the view control in a view, it is not a temporary
display. You are telling Revit how you want to plot this ... (Building Elevation) cat-
egory. Double-click on South.
8. Also in the Project Browser, notice there is a 3D Views category. Expand
the 3D Views category, and double-click on the {3D} choice. ... in Figure 1.40.
Let’...
Autodesk Revit Architecture 2011 No Experience Required - part 8 ppt
... offset the alignment line down. Your plan
should now look like Figure 2.5.
TIP
Notice you did not actually use the Offset command. Revit
Architecture has the offset function built into most ... again. Now, on the
Draw panel, click the Pick Lines icon, as shown in Figure 2.4.
7. Set the Offset to 15
′–0″ (remember, you can just type 15) , as in
Figure 2.4.
FIGURE 2.3 You can grip-...
Autodesk Revit Architecture 2011 No Experience Required - part 17 pptx
... Luckily in Revit Architecture, callouts are not only easy to add to your
model but they directly link to the view they refer to as well. This is crucial for
project coordination. Another nice ... scale. Yes, your call-
out can be at a different scale.
To follow along, open your model, or go to www.sybex.com/go /revit2 011ner
and browse to Chapter 3. Open the file called
NER-09.rvt. If y...
Autodesk Revit Architecture 2011 No Experience Required - part 19 ppt
... to follow along. If you have not com-
pleted the previous chapter procedures, open the file caller
NER-11.rvt found at
the book’s website, www.sybex.com/go /revit2 011ner. Go to the Chapter 4 ... Creating Views
154
NOTE
It’s Revit time! No longer will you see “dumb” placeholder
information in a tag. When we create our construction documents and put
these views on sheets, Revit wi...
Autodesk Revit Architecture 2011 No Experience Required - part 24 pptx
... dimensions are the go-to dimension, they are
put on the bench for most of the game in Revit. The best use for a linear dimen-
sion is when you want to put a straight dimension across nonlinear (angled) ... corridor area.
2. On the Annotate tab, select the Linear Dimension button. Notice that
you cannot select the entire wall. That option has been taken away.
Instead, Revit requires you...
Autodesk Revit Architecture 2011 No Experience Required - part 35 ppt
...
have no idea where
the view is extended
to. Is it to the end
of the building? You
just don’t know. If
you pick the elevation
arrow (the part of the
elevation marker),
you can then grip-
edit ... Properties panel select Exterior - Brick And CMU On MTL.
Stud (No Parapet), as shown in Figure 7.38.
FIGURE 7.38 Changing the walls to Exterior - Brick And CMU On MTL.
Stud (No...
Autodesk Revit Architecture 2011 No Experience Required - part 36 pptx
... canopy roof.
The walls are now joined to the roof, as shown in Figure 7.58.
FIGURE 7.58 The walls are now attached to the roof.
All of the conventional roofing systems have been added. It is now ... reference planes and creating a separate roof
for this canopy. Try to make this a habit!
1. On the Draw panel, click the Start-End-Radius Arc button, as shown
in Figure 7.53.
2. Draw an arc ......
Autodesk Revit Architecture 2011 No Experience Required - part 43 pptx
... Finish Edit Mode.
You now have a plan region. Although it may not seem as though you did any-
thing in the plan, when you place a ceiling at 14
′–6″, you will be able to see it.
NOTE
The dotted ... annoying (especially if you start col-
lecting several plan regions), I recommend that you keep them turned on. It
is helpful to know where a plan region is in the model, and it is more impor-
t...
Autodesk Revit Architecture 2011 No Experience Required - part 45 pptx
... to Level 1 ceiling plan. (Notice that we are
going to a ceiling plan right now, not a floor plan.)
Of course the sink
will come in at the
wrong rotation. By
now you know that
you can tap the ...
the out-of-the box items, but in Chapter 17, we will make some custom millwork
families.
To add some office furniture, follow along:
1. Select the Level 1 floor plan.
2. Zoom into the northeast...
Từ khóa: