Autodesk Revit Architecture 2011 No Experience Required - part 6 ppt

... The Revit Architecture Interface 25 TIP When you change the view control in a view, it is not a temporary display. You are telling Revit how you want to plot this ... in Figure 1.40. Let’s talk about what this icon does. In Revit Architecture, there is no such thing as layers. Line weights are con- trolled by the actual objects they represent. In the view ... My Co M M a n d s...

Ngày tải lên: 07/07/2014, 07:20

... join together (see Figure 2. 16) . 5. We need to add another part of the building. Select and then right-click on one of the exterior walls and select Create Similar. 6. On the View toolbar, set ... offset the alignment line down. Your plan should now look like Figure 2.5. TIP Notice you did not actually use the Offset command. Revit Architecture has the offset function built in...

Ngày tải lên: 07/07/2014, 07:20

... every- thing you do has a downstream effect on the entire model. To follow along, open your model, or go to www.sybex.com/go /revit2 011ner and browse to Chapter 3. Open the file called NER- 06. rvt ... bubble. NOTE Notice that when you are adjusting the levels in the section the 2D icon appears. This means that any adjustments made here will not affect any other views. In a sectional v...

Ngày tải lên: 07/07/2014, 07:20

... Luckily in Revit Architecture, callouts are not only easy to add to your model but they directly link to the view they refer to as well. This is crucial for project coordination. Another nice ... scale. Yes, your call- out can be at a different scale. To follow along, open your model, or go to www.sybex.com/go /revit2 011ner and browse to Chapter 3. Open the file called NER-09.rvt. If y...

Ngày tải lên: 07/07/2014, 08:20

... the 6. Revit will accept that value. If there are fractional increments, you can type 2 6 1/2”, and Revit will accept the value. Or you can type 2 -6 1/2”. FIGURE 4.3 Moving the wall 2′ 6 also ... up. TIP Revit Architecture will accept a few different values for feet and frac- tional inches. For example, instead of typing 2’ 6 (which Revit will accept), you can type 2 6. J...

Ngày tải lên: 07/07/2014, 08:20

... dimensions are the go-to dimension, they are put on the bench for most of the game in Revit. The best use for a linear dimen- sion is when you want to put a straight dimension across nonlinear (angled) ... corridor area. 2. On the Annotate tab, select the Linear Dimension button. Notice that you cannot select the entire wall. That option has been taken away. Instead, Revit requires you...

Ngày tải lên: 07/07/2014, 08:20

... have no idea where the view is extended to. Is it to the end of the building? You just don’t know. If you pick the elevation arrow (the part of the elevation marker), you can then grip- edit ... From the Properties dialog, switch these walls to Exterior - Brick And CMU On MTL. Stud (No Parapet), as shown in Figure 7. 46. FIGURE 7. 46 Changing the wall types as we have bee...

Ngày tải lên: 07/07/2014, 08:20

... Figure 7. 56. 2. Pick the top, back arc on the canopy roof, as shown in Figure 7. 56. 3. Pick the wall that the roof needs to terminate into (see Figure 7. 56) . Chapter 7 • Roofs 3 26 FIGURE 7. 56 Picking ... tab, click the Attach Top/Base button. 6. Select the canopy roof. The walls are now joined to the roof, as shown in Figure 7.58. FIGURE 7.58 The walls are now attached to the ro...

Ngày tải lên: 07/07/2014, 08:20

... with. If you did not complete the previous chapter, go to the book’s web page at www.sybex.com/go /revit2 011ner. From there you can browse to Chapter 9 and find the file called NER- 26. rvt. The objective ... 9. 16 Configuring the View Range for the crop region 6. Click OK. 7. On the Mode panel, click Finish Edit Mode. You now have a plan region. Although it may not seem as though you d...

Ngày tải lên: 07/07/2014, 08:20

... to Level 1 ceiling plan. (Notice that we are going to a ceiling plan right now, not a floor plan.) Of course the sink will come in at the wrong rotation. By now you know that you can tap the ... 3. Select Toilet Stall-Braced-3D : 32″ × 56 Clear from the Change Element Type menu. 4. Click the Edit Type button. 5. Click Duplicate. 6. Change the name to 59” × 60 ” Clear. 7. Click OK....

Ngày tải lên: 07/07/2014, 08:20